CorvetteForum - Chevrolet Corvette Forum Discussion

 
Page 1 of 20
1
2
3
11
Last »
Search: Posts Made By: Russ K
Showing results 1 to 25 of 484
Search took 1.60 seconds.
Forum: C5 Scan & Tune
03-10-2022, 11:58 PM
Replies: 15
Views: 1,509
Posted By Russ K

Sounds like the DFCO is too sensitive. Can you...

Sounds like the DFCO is too sensitive. Can you post your tune?

Russ Kemp
Forum: C5 Tech
04-14-2020, 05:07 PM
Replies: 17
Views: 2,243
Posted By Russ K

I use thread tape on the bleeder screw. Then use...

I use thread tape on the bleeder screw. Then use a vacuum bleeder.

Russ Kemp
Forum: C5 Tech
09-11-2019, 06:38 PM
Replies: 4
Views: 880
Posted By Russ K

The tuner did a speed density tune, and the P0103...

The tuner did a speed density tune, and the P0103 is a result of it. The P0103 has to be current to be in SD mode.

Russ Kemp
Forum: C5 General
05-05-2019, 08:50 PM
Replies: 20
Views: 1,492
Posted By Russ K

The yellow dot is the lightest point of the...

The yellow dot is the lightest point of the tire...
Forum: C5 Tech
02-10-2019, 02:38 PM
Replies: 10
Views: 875
Posted By Russ K

The stock injectors will support ~ 440 RWHP....

The stock injectors will support ~ 440 RWHP. That's assuming your not using E85 fuel.

Russ Kemp
Forum: C5 General
02-10-2019, 02:28 PM
Replies: 18
Views: 1,739
Posted By Russ K

I modified my front Altec splash guards so they...

I modified my front Altec splash guards so they fit 1/2 inch higher.

Russ Kemp
Forum: C5 General
02-10-2019, 02:24 PM
Replies: 88
Views: 117,400
Posted By Russ K

Wheel Make: OZ Wheel Model: Superlegger III ...

Wheel Make: OZ

Wheel Model: Superlegger III

Front Size: 18x9.5

Front Offset or Backspace: +57mm

Rear Size: 19x11
Forum: C5 Tech
01-17-2019, 03:37 PM
Replies: 24
Views: 4,828
Posted By Russ K

Check to see if one of the cables are...

Check to see if one of the cables are broken/disconnected at the hood release lever. If ok, remove the rear wheel house filler panel, then with a long screw driver trip the latch lever.

Russ Kemp
Forum: C5 Tech
01-17-2019, 03:16 PM
Replies: 8
Views: 5,439
Posted By Russ K

This is your issue. Need to disable the trans...

This is your issue. Need to disable the trans Abuse Mode.
Russ Kemp
Forum: C5 Tech
01-14-2019, 02:24 PM
Replies: 24
Views: 2,531
Posted By Russ K

You need these shims;...

You need these shims; https://www.rockauto.com/en/moreinfo.php?pk=593123&jsn=10514

Russ Kemp
Forum: C5 Tech
01-12-2019, 05:24 PM
Replies: 24
Views: 2,531
Posted By Russ K

Slight dimensional differences from the mounting...

Slight dimensional differences from the mounting pad to the starter armature. Some replacement starters come with several thickness starter shims in the box.

Russ Kemp
Forum: C5 Tech
01-12-2019, 04:58 PM
Replies: 24
Views: 2,531
Posted By Russ K

You will need to install a starter shim between...

You will need to install a starter shim between the starter & engine, as there is not enough clearance between the starter drive gear & the flywheel.

Russ Kemp
Forum: C5 Tech
12-10-2018, 02:22 PM
Replies: 3
Views: 1,917
Posted By Russ K

I/P fuse panel? Then #14 fuse is powered when the...

I/P fuse panel? Then #14 fuse is powered when the key in in the crank position.

Russ Kemp
Forum: C5 Tech
09-11-2018, 12:02 AM
Replies: 17
Views: 4,096
Posted By Russ K

Also, I installed the DEI Gold Heat shroud on the...

Also, I installed the DEI Gold Heat shroud on the clutch line and on the remote bleeder line. This is very helpfull when LT Header tubes are close to the clutch line.

Russ Kemp
Forum: C5 Tech
08-20-2018, 06:12 PM
Replies: 103
Views: 14,594
Posted By Russ K

That is defiantly piston slap. As the noise is...

That is defiantly piston slap. As the noise is worse when you blipped the throttle, causing more side load on the piston.

Russ Kemp
Forum: C5 Tech
05-16-2018, 09:55 PM
Replies: 17
Views: 7,013
Posted By Russ K

Is the Trans Abuse Mode set to disabled? Works...

Is the Trans Abuse Mode set to disabled? Works every time for the A4 cars that I've tuned.

Russ Kemp
Forum: C5 Scan & Tune
05-13-2018, 11:25 PM
Replies: 3
Views: 1,741
Posted By Russ K

You need to raise the P0106 Error Map Calculated...

You need to raise the P0106 Error Map Calculated Max table to be slighly higher than your idle map.

Russ Kemp
Forum: C5 General
05-09-2018, 07:39 PM
Replies: 2
Views: 2,620
Posted By Russ K

315/30/19 Michelin Sport Cup

Just mounted the 315/30/19 Sport Cup rear tires. Rear wheels are 11" with a 65mm offset. Still have 1/2" to 11/16" clearance to the inner wheel house.

Front wheels are 18x9.5 57mm offset with...
Forum: C5 Tech
11-19-2017, 08:53 PM
Replies: 27
Views: 4,630
Posted By Russ K

Corvette car line is Y. Russ Kemp

Corvette car line is Y.

Russ Kemp
Forum: C5 General
10-04-2017, 10:19 PM
Replies: 39
Views: 6,984
Posted By Russ K

That table is 100% stock. Of coarse that would...

That table is 100% stock. Of coarse that would cause the P1514 reduced power with your mods.

Russ Kemp
Forum: C5 General
09-22-2017, 09:18 PM
Replies: 39
Views: 6,984
Posted By Russ K

The P1514 code/limp mode is caused when the...

The P1514 code/limp mode is caused when the actual airmass exceeds the P1514 table values in the tune. Stock is .76 g/cyl, and your probably hitting .9 g/cyl.

I would raise the stock P1514 table...
Forum: C5 General
09-25-2016, 10:39 PM
Replies: 3
Views: 633
Posted By Russ K

ALLDATA calls for 6.8 hrs. Russ Kemp

ALLDATA calls for 6.8 hrs.

Russ Kemp
Forum: C5 Tech
04-27-2016, 05:05 PM
Replies: 14
Views: 2,909
Posted By Russ K

When Lt headers are installed, it's very common...

When Lt headers are installed, it's very common to get slow response codes (P0133 & P0153). Also insufficient switching (P1133 & P1153) codes are very common as well with Lt Headers. Just set these...
Forum: C5 General
03-29-2016, 11:19 AM
Replies: 50
Views: 11,882
Posted By Russ K

Not bolting down a 4 post lift is very unsafe....

Not bolting down a 4 post lift is very unsafe. Maybe if there were some diagonal bracing added, it would help.

Russ Kemp
Forum: C5 Parts for Sale/Wanted
03-02-2016, 07:18 PM
Replies: 0
Views: 446
Posted By Russ K

EPS 234/242/.600/.615/117+6 cam for sale

I'm selling a EPS 234/242/.600/.615/117+6 camshaft. I bought it in March 2013 from EPS. It only has 10,000 miles on it, and is in perfect condition. I always used Joe Gibbs & Royal Purple HPS oil. I...
Showing results 1 to 25 of 484
 
Page 1 of 20
1
2
3
11
Last »


 
Forum Jump

Trending Topics

All times are GMT -4. The time now is 08:26 PM.