Search: Posts Made By: blackbear bob
Showing results 1 to 25 of 494
Search took 2.05 seconds.
Forum: C5 General
12-20-2018, 05:39 PM
Replies: 30
Views: 2,468
Posted By blackbear bob

That's just a whole package of what the hell

That's just a whole package of what the hell
Forum: C5 Tech
11-22-2018, 04:21 PM
Replies: 8
Views: 2,947
Posted By blackbear bob

They are not much money. The intake manifold job...

They are not much money. The intake manifold job is fairly easy and you do get to clean up a lot of stuff. Be very careful around plastic things such as the evap line. It tends to be very brittle.
Forum: C5 Tech
11-03-2018, 10:06 AM
Replies: 4
Views: 622
Posted By blackbear bob

I would start with the simple things. Condition...

I would start with the simple things. Condition and age of the tires?
Forum: C5 Tech
09-04-2018, 05:34 PM
Replies: 1
Views: 385
Posted By blackbear bob

Condensation causing rust haze on brakes? Wheel...

Condensation causing rust haze on brakes? Wheel bearing and half shaft noises don't go away.
Forum: C5 General
09-04-2018, 05:13 PM
Replies: 28
Views: 2,652
Posted By blackbear bob

3 years and going strong with my Interior...

3 years and going strong with my Interior Innovations full leather.
Forum: C5 General
08-29-2018, 04:18 PM
Replies: 70
Views: 6,882
Posted By blackbear bob

Firestone Indy 500 from Tire Rack Have 10k...

Firestone Indy 500 from Tire Rack
Have 10k flawless miles on them this summer
can't beat the price
You will get lots of opinions here
Forum: C5 Tech
08-25-2018, 05:33 PM
Replies: 9
Views: 710
Posted By blackbear bob

your second thought is correct

your second thought is correct
Forum: C5 Tech
08-19-2018, 10:36 AM
Replies: 1
Views: 566
Posted By blackbear bob

Codes ?

Codes ?
Forum: C5 General
08-17-2018, 02:52 PM
Replies: 18
Views: 1,823
Posted By blackbear bob

Steering wheel wrap and floor mat says it all.

Steering wheel wrap and floor mat says it all.
Forum: C5 General
07-30-2018, 06:27 AM
Replies: 2
Views: 544
Posted By blackbear bob

Looks like a grommet for a MAP sensor. May have...

Looks like a grommet for a MAP sensor. May have had one changed in the past.
Forum: C5 General
07-18-2018, 11:54 AM
Replies: 11
Views: 1,505
Posted By blackbear bob

I would think being in Az you should be fine.

I would think being in Az you should be fine.
Forum: C5 Tech
07-15-2018, 07:06 PM
Replies: 2
Views: 531
Posted By blackbear bob

The noise that you are hearing sounds to be like...

The noise that you are hearing sounds to be like a low speed ABS activation. This is usually caused by a wheel speed sensor "dropping out"
It also could explain your sketchy feeling when first...
Forum: C5 Tech
07-08-2018, 05:23 PM
Replies: 12
Views: 2,361
Posted By blackbear bob

Yes the sensors are four wire, Don't have a...

Yes the sensors are four wire, Don't have a diagram in front of me but if memory serves, pink to black is the heater circuit on the car side of the harness. The sensor may come with two white and two...
Forum: C5 Tech
07-08-2018, 05:13 PM
Replies: 6
Views: 1,238
Posted By blackbear bob

Drive safe

Drive safe
Forum: C5 Tech
07-08-2018, 05:08 PM
Replies: 12
Views: 2,361
Posted By blackbear bob

Yes you can ohm the heater on the drivers side...

Yes you can ohm the heater on the drivers side and compare the reading to that of the passenger side. All things being equal, The sensors have been through the same amount of heat cycles, and one of...
Forum: C5 Tech
07-08-2018, 05:03 PM
Replies: 6
Views: 1,238
Posted By blackbear bob

No. The graphs that you posted are for one side...

No. The graphs that you posted are for one side (bank 1 in your case). Front sensors should be in constant motion from about .100 to .900 volts
Rear sensors should remain nearly flat. If a front and...
Forum: C5 Tech
07-08-2018, 04:58 PM
Replies: 12
Views: 2,361
Posted By blackbear bob

Bank 2 sensor 2 heater circuit. Most likely cause...

Bank 2 sensor 2 heater circuit. Most likely cause is a burnt heater element inside the sensor. The main reason that I asked is to rule out sensor performance problems. If you have a DVOM you can ohm...
Forum: C5 Tech
07-08-2018, 04:54 PM
Replies: 6
Views: 1,238
Posted By blackbear bob

Code p1153 is for bank 2 sensor one and the graph...

Code p1153 is for bank 2 sensor one and the graph that you posted is for bank 1 sensor one. It looks fine by the way.
Forum: C5 Tech
07-08-2018, 04:49 PM
Replies: 10
Views: 840
Posted By blackbear bob

pjensen is spot on. Flush, Flush, Flush. When you...

pjensen is spot on. Flush, Flush, Flush. When you think that you got it all, flush it two more times. Any metal in the system will at least hurt performance, and at worst cost you another compressor.
Forum: C5 Tech
07-08-2018, 04:43 PM
Replies: 12
Views: 2,361
Posted By blackbear bob

What was the code number? It would indicate which...

What was the code number? It would indicate which sensor was having the problem and what said problem was. As far as sensor brands, I believe that Denso makes the OE sensors for GM.
Quality pieces....
Forum: C5 General
07-08-2018, 06:29 AM
Replies: 21
Views: 1,271
Posted By blackbear bob

Thief.

Thief.
Forum: C5 General
07-07-2018, 07:10 AM
Replies: 2
Views: 1,078
Posted By blackbear bob

:lurk:

:lurk:
Forum: C5 General
07-05-2018, 09:05 AM
Replies: 40
Views: 2,055
Posted By blackbear bob

Hi and welcome, I kind of like the C4 wheel with...

Hi and welcome, I kind of like the C4 wheel with the polished lips. Are they 17 all around?
Forum: C5 Tech
06-30-2018, 08:16 PM
Replies: 4
Views: 611
Posted By blackbear bob

If you have tools available to you, I would just...

If you have tools available to you, I would just top it off and run it. Fix it when you get home.
Forum: C5 General
06-30-2018, 04:45 PM
Replies: 8
Views: 1,974
Posted By blackbear bob

If you have some available to you, valve grinding...

If you have some available to you, valve grinding compound works great to remove stripped screws. Same ideal, just put some in the head of the screw and remove with t15. Also works on...
Showing results 1 to 25 of 494
 


 
Forum Jump


All times are GMT -4. The time now is 02:38 PM.