CorvetteForum - Chevrolet Corvette Forum Discussion

 
Page 1 of 9
1
2
3
Last »
Search: Posts Made By: 1BAD80
Showing results 1 to 25 of 215
Search took 1.40 seconds.
Forum: C5 General
08-30-2021, 06:57 PM
Replies: 19
Views: 1,275
Posted By 1BAD80

Hold the traction control down about 5 seconds...

Hold the traction control down about 5 seconds you will get a tone and shows up competitive driving in the info window
Forum: C3 Tech/Performance
10-10-2018, 06:22 PM
Replies: 10
Views: 1,758
Posted By 1BAD80

sounds like a wire is not in the right place or...

sounds like a wire is not in the right place or the switch itself
Forum: C3 Tech/Performance
12-19-2016, 11:29 AM
Replies: 26
Views: 1,418
Posted By 1BAD80

http://forums.holley.com/entry.php?439-How-To-Adju...

http://forums.holley.com/entry.php?439-How-To-Adjust-The-Electric-Choke-On-A-Holley-Four-Barrel-Carburetor
Forum: C3 Tech/Performance
12-19-2016, 11:16 AM
Replies: 26
Views: 1,418
Posted By 1BAD80

depends on where the vacuum is hooked up carb...

depends on where the vacuum is hooked up carb port or manifold

if the auto trans is hooked to to the radiator it should be on a cooler of it's own

The temp sensor can be bad or loose wire...
Forum: C3 Tech/Performance
12-14-2016, 08:35 PM
Replies: 26
Views: 1,418
Posted By 1BAD80

I was also going to say the choke is closed to...

I was also going to say the choke is closed to much :thumbs:

it has to be adjusted on a cold motor and the throttle held about 1/4 down and the choke should be open about 1/8"
when the motor...
Forum: C3 Tech/Performance
12-14-2016, 04:50 PM
Replies: 26
Views: 1,418
Posted By 1BAD80

I would say the choke & carb are not adjusted...

I would say the choke & carb are not adjusted correctly, I run a cross ram with .625 lift and idles at 650 rpm. w/ full roller motor

what type of distributor are you running ?
if vacuum how is...
Forum: C5 Tech
11-23-2012, 09:25 PM
Replies: 28
Views: 47,674
Posted By 1BAD80

I copyed and pasted this from...

I copyed and pasted this from http://www.antennamastsrus.com/GM/Cheverolet/Corvette/Instructions.htm

Corvette Power Antenna Mast Instructions

Before installing your new mast, compare the old...
Forum: C5 Parts for Sale/Wanted
11-13-2012, 04:02 PM
Replies: 229
Views: 14,954
Posted By 1BAD80

How about the radio power attena ?

How about the radio power attena ?
Forum: C3 Tech/Performance
10-31-2012, 01:40 PM
Replies: 41
Views: 10,706
Posted By 1BAD80

I run AC # PF-932 2 qt. and can order from...

I run AC # PF-932 2 qt. and can order from any good part's shop.
Cost around $12.00

There are a few others that cross reference to it.
Forum: C3 Parts for Sale/Wanted
02-07-2012, 07:28 PM
Replies: 0
Views: 238
Posted By 1BAD80

WTB 80 lower alternator mounting bracket

WTB 80 lower alternator mounting bracket
Forum: C3 Parts for Sale/Wanted
02-07-2012, 07:23 PM
Replies: 117
Views: 11,980
Posted By 1BAD80

Im looking for a lower Alternator Mounting Bracket

Im looking for a lower Alternator Mounting Bracket
Forum: C3 Tech/Performance
08-10-2010, 02:19 PM
Replies: 13
Views: 3,057
Posted By 1BAD80

FYI, If you ever need one GM Service Parts has...

FYI, If you ever need one GM Service Parts has the aluminum 5 blade fan with the thermo clutch setup. & aluminum water pump all for less than $200.
Forum: C5 Tech
09-03-2008, 07:07 PM
Replies: 2,003
Views: 757,315
Posted By 1BAD80

I just ordered one from Adaptive Performance $40....

I just ordered one from Adaptive Performance $40. delivered
Column Lock Bypass
$35.95 / U.S.ONLY Priority mail delivery$4.05
http://www.adaptiveperformance.com/CLB.htm
Forum: C3 Tech/Performance
02-14-2008, 08:48 PM
Replies: 5
Views: 359
Posted By 1BAD80

I got mine from here, ...

I got mine from here,
http://www.drivetrainspecialists.com/
When you remove the half shaft there is a large nut to remove it.
Forum: C3 Tech/Performance
01-24-2008, 08:44 PM
Replies: 8
Views: 545
Posted By 1BAD80

It really don't matter how they look, you will...

It really don't matter how they look, you will never be going slow enough to see them anyway. :crazy:

They should look good with the rear set. :thumbs:

Good choice for cooling those brake's...
Forum: C3 Tech/Performance
10-31-2007, 08:16 PM
Replies: 17
Views: 5,595
Posted By 1BAD80

Backspacing on stock rims on an 80 is 4 5/8" ,...

Backspacing on stock rims on an 80 is 4 5/8" , with offset trailing arms I installed Centerline Conve Pro's 15/10.5 front 15/12 rear with 5" backspacing. With a short spring.
Forum: C3 Tech/Performance
10-09-2007, 08:48 PM
Replies: 18
Views: 2,129
Posted By 1BAD80

From TCI; Drivability concerns in choosing a...

From TCI;
Drivability concerns in choosing a torque converter - A performance torque converter should not compromise one aspect of car performance to achieve another. When investigating a converter...
Forum: C3 Tech/Performance
10-07-2007, 08:58 PM
Replies: 17
Views: 9,437
Posted By 1BAD80

You should do it just because. The Kinsler...

You should do it just because.

The Kinsler unit is very good for the street and strip.
I run a cross ram on my 434 sbc and its great on the street with no issues.
Tuning is not hard with the...
Forum: C3 Tech/Performance
09-15-2007, 08:57 PM
Replies: 15
Views: 4,164
Posted By 1BAD80

I copied this from somewhere, and it's the way I...

I copied this from somewhere, and it's the way I adjust lifters.
:thumbs:

Setting Valve Lash on Mechanical Cams

All the valves must be set individually and only when the lifter is...
Forum: C3 Tech/Performance
08-18-2007, 07:54 AM
Replies: 32
Views: 3,738
Posted By 1BAD80

I have used Royal Purple for years with good...

I have used Royal Purple for years with good results.
The gear lube took away most of the noise from the rearend gears inside the car.
A friend works at a local dealer and I changed the lubes in...
Forum: C3 Tech/Performance
08-11-2007, 06:10 PM
Replies: 7
Views: 2,384
Posted By 1BAD80

It would be good to know what motor work has been...

It would be good to know what motor work has been done or all stock.
I run a cross ram, the next best thing would be a Berry Grant tri-power.
I do not like the other brand mentioned. :ack:
A...
Forum: C3 Tech/Performance
07-19-2007, 08:25 PM
Replies: 7
Views: 663
Posted By 1BAD80

Crud behind the pistons. :thumbs:

Crud behind the pistons. :thumbs:
Forum: C5 Tech
07-17-2007, 08:09 PM
Replies: 41
Views: 4,224
Posted By 1BAD80

I just picked up an 03 a few weeks ago, I also...

I just picked up an 03 a few weeks ago, I also have a ticking noise just like a rocker.
It's the idle pully on the top middle of the motor, I can put my finger on it and the noise stops. :smash:
I...
Forum: C3 Tech/Performance
07-17-2007, 07:53 PM
Replies: 21
Views: 1,192
Posted By 1BAD80

SWEET nothing like a roller motor. Glad to...

SWEET nothing like a roller motor.
Glad to hear no problems and run's the way you built it. :thumbs: :cheers:
Forum: C5 Tech
07-14-2007, 05:37 PM
Replies: 9
Views: 440
Posted By 1BAD80

This site explains how to, ...

This site explains how to,
http://www.corvettefever.com/
Showing results 1 to 25 of 215
 
Page 1 of 9
1
2
3
Last »


 
Forum Jump

Trending Topics

All times are GMT -4. The time now is 09:14 PM.