Search: Posts Made By: PUNISHERC6
Showing results 1 to 21 of 21
Search took 0.96 seconds.
01-15-2014, 04:24 PM
Replies: 110
Views: 10,626
Posted By PUNISHERC6

I like the Z with the paddles, as the owner of a...

I like the Z with the paddles, as the owner of a 6spd C6, I love my stick but every now and again I thought it would be nice to relax a lil bit...and then I drove a R8 V10 with the DCT.....I'll take...
12-22-2012, 12:40 PM
Replies: 23
Views: 10,103
Posted By PUNISHERC6

where exactly did you put the tape and did you...

where exactly did you put the tape and did you have to remove the cowl cover in order to do this...this buzzing is driving me insane and the dealership I bought the car from is totally inadequate!!!!...
12-10-2011, 12:50 PM
Replies: 34
Views: 4,577
Posted By PUNISHERC6

lightweight

It's amazing how many heavy parts have to be added to a vehicle just to counter the other heavy parts needed in a vehicle. For instance, Corvettes have large heavy brakes and stock wheels that weigh...
Forum: C5 Tech
12-10-2011, 12:07 PM
Replies: 23
Views: 9,158
Posted By PUNISHERC6

Cupping tires

I've also had an issue with cupped tires but just the inside of the left front one to the point of it making a wump wump noise that increased with speed with just a little vibration. The car also...
08-05-2011, 04:52 PM
Replies: 18
Views: 1,933
Posted By PUNISHERC6

checked my tires today after flushing and filling...

checked my tires today after flushing and filling the clutch reservoir AGAIN lol, right tire is doing ok, left tire is starting to show some real wear on the inside....I wanna go to Michelins so bad...
08-05-2011, 04:46 PM
Replies: 138
Views: 8,984
Posted By PUNISHERC6

it was the V10 version

it was the V10 version
08-05-2011, 04:43 PM
Replies: 18
Views: 1,933
Posted By PUNISHERC6

don't think it has anything to do with ther rear...

don't think it has anything to do with ther rear since I can actually hold the wheel where it's supposed to be to go straight and if i let it go, the wheel will start to rotate to one side and the...
08-01-2011, 11:48 PM
Replies: 18
Views: 1,933
Posted By PUNISHERC6

anyone have an issue with the car pulling to one...

anyone have an issue with the car pulling to one side, taking it in for allignment, setting everything to factory specs and the car still pulls to the right. have had the car aligned 5 times in 20k...
01-31-2010, 07:14 PM
Replies: 16
Views: 51,155
Posted By PUNISHERC6

it was loaded.

it was loaded.
01-30-2010, 10:13 PM
Replies: 106
Views: 47,796
Posted By PUNISHERC6

378 hp and 380 lbs torque stock, 407.9 hp and 412...

378 hp and 380 lbs torque stock, 407.9 hp and 412 lbs with CAI and tune, 439 hp and 446 lbs after kooks long tubes, random tech cats, X tubing and stock NPP mufflers in the open position at 12.5:1...
01-30-2010, 12:33 PM
Replies: 16
Views: 51,155
Posted By PUNISHERC6

my 09 LS3 put down 378.9 hp and 380 lbs bone...

my 09 LS3 put down 378.9 hp and 380 lbs bone stock, back with a mamba cold air intake and a mild tune and it was up to 408.7 hp and 412.8 lbs. with cold air, long tubes, high flow cats and stock NPP...
01-30-2010, 08:59 AM
Replies: 68
Views: 3,938
Posted By PUNISHERC6

in my experience, if your car has less than 7500...

in my experience, if your car has less than 7500 miles, the dealership will do it under warranty, if it's higher then about $65.00 to $75,00 is about normal, but again, find a dealer that does a lot...
01-30-2010, 06:35 AM
Replies: 97
Views: 5,603
Posted By PUNISHERC6

I've changed the reverse lights as well as the...

I've changed the reverse lights as well as the license plate bulbs to led bulbs, the reverse lamps are brighter and the license plate lamps just make the car look really nice, especially when it's...
01-15-2010, 11:45 PM
Replies: 32
Views: 17,653
Posted By PUNISHERC6

just an upgrade, found the bulbs on ebay for...

just an upgrade, found the bulbs on ebay for 100.00 for the pair in the temp I wanted. I found the HID foglight kit for 45.00 so I'll be doing both of them at the same time, picked up all the tools...
01-14-2010, 10:41 PM
Replies: 32
Views: 17,653
Posted By PUNISHERC6

thanks buddy, it helps alot, I'll be going to...

thanks buddy, it helps alot, I'll be going to sears tomorrow to get a magnetized 15 torx tip to take out the bulbs, i'm sure it will be less than 110.00 lol, thanks alot
01-14-2010, 10:36 PM
Replies: 14
Views: 4,555
Posted By PUNISHERC6

what tool did you use to get the 2 screws out,...

what tool did you use to get the 2 screws out, I've tried philips, torx, and allen lol, help!
01-14-2010, 10:18 PM
Replies: 32
Views: 17,653
Posted By PUNISHERC6

yeah it seems that way since i've been looking...

yeah it seems that way since i've been looking online for about 4 hours now trying to find someone who's done it and no luck so far
01-14-2010, 09:57 PM
Replies: 18
Views: 1,260
Posted By PUNISHERC6

I am also worried about issues with my ecu since...

I am also worried about issues with my ecu since I am thinking of getting a second ecu to replace my tuned one on my 09' Z51 optioned c6 which is now puting down 410 hp at the wheels so some solid...
01-14-2010, 09:46 PM
Replies: 32
Views: 17,653
Posted By PUNISHERC6

how to change the D1S low beam HID bulb in a C6 corvette, please help!

I'm trying to find someone who knows how to change out the low beam hid lamp on a 2009 C6, I know how to get to the bulb itself but it seams to have 2 fasteners which hold a retainer. if someone...
Forum: Intros
03-11-2009, 11:22 PM
Replies: 22
Views: 348
Posted By PUNISHERC6

welcome to the site

welcome to the site
Forum: Intros
01-04-2009, 12:13 PM
Replies: 17
Views: 247
Posted By PUNISHERC6

New '09 C6 owner

Hey there all, just wanted to say hello to you all and I hope to see you out on the road while I'm driving my Cyber Grey C6!
Showing results 1 to 21 of 21


 
Forum Jump


All times are GMT -4. The time now is 12:30 PM.