CorvetteForum - Chevrolet Corvette Forum Discussion

 
Page 1 of 20
1
2
3
11
Last »
Search: Posts Made By: Fred@ReverseLogic
Showing results 1 to 25 of 485
Search took 1.19 seconds.
Forum: C7 Z06 Discussion
12-29-2019, 01:56 PM
Replies: 8
Views: 1,339
Posted By Fred@ReverseLogic

As long as the contact patch on the tires is 12"...

As long as the contact patch on the tires is 12" wide or less you should be okay. Reverse Logic's sponsorship for CF ends in two days. I won't be able to reply afterwards.
Forum: C7 Vendor for Sale
12-18-2019, 07:13 PM
Replies: 1
Views: 375
Posted By Fred@ReverseLogic

One more item available.... RR-RESTYLE-IN-16...

One more item available....

RR-RESTYLE-IN-16 extra set of inclines for RR-RESTYLE-16 full lift ramps. MSRP $475. Close out $250.
Forum: C7 Vendor for Sale
12-17-2019, 09:55 AM
Replies: 1
Views: 375
Posted By Fred@ReverseLogic

Race Ramps inventory clearance - Philadelphia Area only

Reverse Logic has been a CF sponsor for close to ten years. During that time we sold thousands of Race Ramps both on line and at many Carlisle, PA Car Shows. Many forum members recognized the...
Forum: C7 General Discussion
12-17-2019, 08:29 AM
Replies: 36
Views: 2,709
Posted By Fred@ReverseLogic

The Race Ramps wheel chocks have "teeth" on the...

The Race Ramps wheel chocks have "teeth" on the bottom surface which help to keep them in place when positioned behind the front tires on the incline portion of the platforms. If you try to remove...
Forum: C7 General Discussion
12-14-2019, 10:49 AM
Replies: 36
Views: 2,709
Posted By Fred@ReverseLogic

The RR-72-2 ramps are the equivalent of the...

The RR-72-2 ramps are the equivalent of the RR-56-2 plus RR-EX-12. The 72" ramps are a more elegant solution and are available for under $300.00.

https://reverselogic.us/2-stage-incline-ramps
Forum: C7 General Discussion
12-11-2019, 08:32 AM
Replies: 41
Views: 13,131
Posted By Fred@ReverseLogic

Drilling holes in Race Ramps is not a good idea....

Drilling holes in Race Ramps is not a good idea. Exposing the foam will compromise the integrity of the ramps. Cars driving perpendicular to the ramps secured to the pavement as they passed by the...
Forum: C7 General Discussion
12-11-2019, 08:16 AM
Replies: 41
Views: 13,131
Posted By Fred@ReverseLogic

Others considering this solution should keep the...

Others considering this solution should keep the following in mind. The Race Ramps RR-EX-14 XTenders are intended to be used with a service ramp which has a 10.8 degree incline. It appears that the...
Forum: C7 General Discussion
12-02-2019, 05:23 PM
Replies: 40
Views: 4,020
Posted By Fred@ReverseLogic

There are a couple of ramp models that have a...

There are a couple of ramp models that have a cradle top platform that help to keep the non-drive wheels on the ramp when you lift the other end of the car.

RLL-80-2, RR-80-10-2
Forum: Car Care Discussion
11-06-2019, 09:07 PM
Replies: 8
Views: 699
Posted By Fred@ReverseLogic

Race Ramps is offering a cash back factory rebate...

Race Ramps is offering a cash back factory rebate on Flatstopper purchases through 31-Jan-2020.
Forum: C6 Corvette ZR1 & Z06
10-16-2019, 09:41 AM
Replies: 25
Views: 2,759
Posted By Fred@ReverseLogic

You probably have the RLL-80-2 80" ramps rather...

You probably have the RLL-80-2 80" ramps rather than the 87" ramps. The 80" ramps include the 56" long invertible incline sections that can be used as trailer ramps. The incline section for the 87"...
Forum: C6 Corvette General Discussion
05-15-2019, 06:27 AM
Replies: 11
Views: 2,045
Posted By Fred@ReverseLogic

If you have sufficient spoiler-to-ground...

If you have sufficient spoiler-to-ground clearance when the rear tires are on the 10" high platforms, you will also have enough clearance when the rear tires are on the second stage incline section....
Forum: C6 Corvette General Discussion
05-14-2019, 11:06 PM
Replies: 11
Views: 2,045
Posted By Fred@ReverseLogic

The Roll-ups formula works for both directions....

The Roll-ups formula works for both directions. The ground clearance formula could be used to calculate clearance below whatever is the lowest thing on the rear of the car (i.e. diffuser, exhaust...
Forum: C6 Corvette General Discussion
05-14-2019, 10:30 PM
Replies: 11
Views: 2,045
Posted By Fred@ReverseLogic

Here's a formula you can use to estimate the...

Here's a formula you can use to estimate the clearance below the spoiler with the rear tires on the ramp platforms.

LGC - ((OH/WB) x RH) = AGC

Legend:
LGC = Ground clearance below spoiler when...
Forum: C6 Corvette ZR1 & Z06
02-24-2019, 12:58 PM
Replies: 16
Views: 4,964
Posted By Fred@ReverseLogic

The 67" RR-XT-2 ramps have a 10.8 degree incline....

The 67" RR-XT-2 ramps have a 10.8 degree incline. They are not the most shallow sloped service Race Ramps available. The RR-80-10-2 ramps have an 8.5 degree incline. The two-stage incline RR-72-2...
Forum: C7 Tech/Performance
01-21-2019, 05:40 PM
Replies: 17
Views: 1,442
Posted By Fred@ReverseLogic

If you can raise the yardstick to 6" then the...

If you can raise the yardstick to 6" then the RR-80-10-2 ramp with an 8.5 degree approach angle will work.

If you can raise the yardstick to 5" then you can use one of the options with a 6.8...
Forum: C7 Tech/Performance
01-21-2019, 12:48 PM
Replies: 17
Views: 1,442
Posted By Fred@ReverseLogic

The RR-XT-2 (67" ramps) have the same exact slope...

The RR-XT-2 (67" ramps) have the same exact slope as the RR-56-2 ramps, 10.8 degrees. So when the ramps are pushed up against the tires the car-to-ramp clearance is the same for both of these ramps...
Forum: C7 General Discussion
12-12-2018, 12:56 PM
Replies: 20
Views: 1,940
Posted By Fred@ReverseLogic

The length of the T-nut shaft plus the thickness...

The length of the T-nut shaft plus the thickness of the spacer between the T-nut and puck on the Reverse Logic jack pad is such that it will work with either the steel of aluminum chassis. That's why...
Forum: C7 Vendor for Sale
07-28-2018, 03:19 PM
Replies: 0
Views: 399
Posted By Fred@ReverseLogic

Race Ramps at Corvettes at Carlisle 2018

Reverse Logic will be showcasing popular Race Ramps models at the 2018 Corvettes at Carlisle Car Show from August 23 thru 26. We will have the new RLL-116-3 ramps on display in our vendor space in...
Forum: Canadian Events
07-25-2018, 08:17 AM
Replies: 7
Views: 2,164
Posted By Fred@ReverseLogic

Depending upon your location in Canada, it may be...

Depending upon your location in Canada, it may be possible to pick up the ramps at a border town in the USA. Just about all Race Ramps resellers ship the ramps for free to destinations in the...
Forum: C7 Parts for Sale/Wanted
06-19-2018, 04:48 PM
Replies: 21
Views: 1,917
Posted By Fred@ReverseLogic

You can estimate the clearance by doing the...

You can estimate the clearance by doing the following.

1) Push one end of a yardstick up against the inboard edge of the tire.
2) Prop the other end of the yardstick up to a height of 7.25".
3)...
Forum: C7 General Discussion
05-06-2018, 07:44 PM
Replies: 9
Views: 2,015
Posted By Fred@ReverseLogic

Any of the Race Ramps with a 6.8 degree initial...

Any of the Race Ramps with a 6.8 degree initial incline should work. This includes models RR-72-2, RLL-80-2, and RLL-87-2.

You can use the Service Ramp Calculator at...
Forum: C6 Tech/Performance
05-03-2018, 12:42 PM
Replies: 18
Views: 2,233
Posted By Fred@ReverseLogic

I believe the ramps shown in the photo in the...

I believe the ramps shown in the photo in the previous post are the RR-TR-5. You can compare this ramp to some of the custom Race Ramps available at this link.
...
Forum: C6 Tech/Performance
05-03-2018, 10:14 AM
Replies: 18
Views: 2,233
Posted By Fred@ReverseLogic

I don't think this configuration will work unless...

I don't think this configuration will work unless the edge of the door is supported with large blocks on the hinge side of the flap.

The calculator referred to above will describe the shape of the...
Forum: C6 Tech/Performance
05-02-2018, 08:02 AM
Replies: 18
Views: 2,233
Posted By Fred@ReverseLogic

Race Ramps makes a dozen custom ramp models for...

Race Ramps makes a dozen custom ramp models for Reverse Logic. One ramp model, the RLL-TR-105-2, has an initial incline of 2.2 degrees. That's a lot less than the standard ramp models.

You can...
Forum: C7 General Discussion
04-17-2018, 09:40 PM
Replies: 20
Views: 2,869
Posted By Fred@ReverseLogic

Use the service ramp calculator at...

Use the service ramp calculator at https://www.reverselogic.us/race-ramps to determine which ramp offers the desired car-to-ramp clearance.

Several ramp models include integrated Xtenders. The...
Showing results 1 to 25 of 485
 
Page 1 of 20
1
2
3
11
Last »


 
Forum Jump

Trending Topics

All times are GMT -4. The time now is 12:48 AM.