CorvetteForum - Chevrolet Corvette Forum Discussion

Search: Posts Made By: msessine
Showing results 1 to 15 of 15
Search took 1.10 seconds.
Forum: C4 Parts for Sale/Wanted
07-30-2007, 08:34 PM
Replies: 6
Views: 427
Posted By msessine

Did you sell the hatch? let me know - ...

Did you sell the hatch? let me know - mdsessine@comcast.net
Forum: C4 Parts for Sale/Wanted
06-18-2007, 11:05 PM
Replies: 0
Views: 301
Posted By msessine

Targa Top

F/S Targa top, blue acrylic. Packing slip lists it for 86L-88. Bought new from corvette south for $1037 including shipping. Still in box, sold car. $700 & you pay shipping 781 293-2299,...
Forum: C4 Tech/Performance
06-08-2007, 03:58 PM
Replies: 2
Views: 391
Posted By msessine

Thanks a million 86, although my test light shows...

Thanks a million 86, although my test light shows power the fusible link must be junk. Thanks again for your reply.
Mike
Forum: C4 Tech/Performance
06-07-2007, 10:42 PM
Replies: 2
Views: 391
Posted By msessine

fuel pump relay

On my 87, after a momentary shorting of the battery terminal while working near the battery the car would not start. No power on any pin of the fuel pump relay. I've checked every fuse I could find...
Forum: C4 Parts for Sale/Wanted
08-08-2006, 06:19 PM
Replies: 0
Views: 226
Posted By msessine

FS-Be Cool aluminum radiator

I have a Be Cool aluminum radiator part # 62046 listed for a 87 corvette-high altitude-(no fill cap). When I purchased this radiator it was listed as fitting 86-96 corvettes however it did not...
Forum: C4 Parts for Sale/Wanted
08-08-2006, 05:46 PM
Replies: 4
Views: 365
Posted By msessine

Valve covers sold, thanks for all your interest. ...

Valve covers sold, thanks for all your interest.
Mike
Forum: C4 Parts for Sale/Wanted
08-06-2006, 08:46 PM
Replies: 4
Views: 365
Posted By msessine

FS Valve Covers-Aftermarket

I have a set of valve covers I bought online after someone on the forum tried them and they fit however, they would not clear my pro comp roller rockers so I had to go with tall covers. They are ball...
Forum: C4 Tech/Performance
08-05-2006, 10:33 PM
Replies: 7
Views: 674
Posted By msessine

I relaced mine last week. Take the fender off...

I relaced mine last week. Take the fender off (vent) that covers the bottle and remove the rear section of the wheel well. this will expose the bolt in the rear of the bottle. Once you have the...
Forum: C4 Tech/Performance
06-05-2006, 10:16 PM
Replies: 3
Views: 394
Posted By msessine

Yes I installed energy suspension bushings....

Yes I installed energy suspension bushings. Thanks for all the input. I'll get the alignment and update afterwoods.

Thanks mike
Forum: C4 Tech/Performance
06-04-2006, 09:44 PM
Replies: 3
Views: 394
Posted By msessine

Handling problem after lowering

I lowered my 87 and installed adjustable strut rods and replaced rear bushings and now it feels like the rear end is on ice at the slightest touch of the wheel. I adjusted the height and camber every...
Forum: C4 Tech/Performance
05-15-2006, 03:32 PM
Replies: 47
Views: 4,870
Posted By msessine

I took my 87 to front end shop to do a wheel...

I took my 87 to front end shop to do a wheel alignment and they told me they could not do it cause the rear wheel bearing was gone. I replaced it along with the control arm bushings and had the same...
Forum: C4 General Discussion
05-05-2006, 11:26 PM
Replies: 25
Views: 756
Posted By msessine

If you would'nt mind look:) ing up the seller i...

If you would'nt mind look:) ing up the seller i would appreciate it.
Forum: C4 General Discussion
05-05-2006, 08:53 PM
Replies: 25
Views: 756
Posted By msessine

What brand are the valve covers? I had to cut...

What brand are the valve covers? I had to cut mine to clear the wiper motor, and yes what EGR?
Forum: C4 General Discussion
05-05-2006, 08:47 PM
Replies: 25
Views: 1,236
Posted By msessine

I swapped my motor out in an 87. I had a local...

I swapped my motor out in an 87. I had a local shop build a 4 bolt 350/350 all roller for $3700.00. i had to modify the tall valve covers to clear the wiper motor.:crazy: Do yourself a favor and...
Forum: C4 Parts for Sale/Wanted
05-04-2006, 10:23 PM
Replies: 6
Views: 312
Posted By msessine

I'll take the half shaft if you still have...

I'll take the half shaft if you still have it.:smash:
Showing results 1 to 15 of 15


 
Forum Jump

Trending Topics

All times are GMT -4. The time now is 12:04 PM.