Danvilee Va / Greensboro NC area body shop ?
#1
Instructor
Thread Starter
Danvilee Va / Greensboro NC area body shop ?
Hi folks..
Bambi got my 71 ..
Looking for a Corvette body shop in South side VA or Triad area.
Any recommendations would be appreciated.
Most in my area (Reidsville, NC) just honestly don't like fiberglass work.
thanks.
Bambi got my 71 ..
Looking for a Corvette body shop in South side VA or Triad area.
Any recommendations would be appreciated.
Most in my area (Reidsville, NC) just honestly don't like fiberglass work.
thanks.
#2
Tech Contributor
#4
Instructor
Thread Starter
Randy ,
Thanks for the referral to Greg .
He looked at the car and I finally felt like
a corvette guy was looking at my car.
He's working up some #'s and looks like he get the car.
thanks again.
Patrick
Thanks for the referral to Greg .
He looked at the car and I finally felt like
a corvette guy was looking at my car.
He's working up some #'s and looks like he get the car.
thanks again.
Patrick
#5
Tech Contributor
He's had some practice on my car so he is familiar with C6's now.
#7
Tech Contributor
Yes, you will need to keep on Greg. He does good work but he had my Corvette way too long this last time he worked on it.
Stay after him to give you an estimated finish date and then pester him once it comes an goes. (Don't tell him I said that)
If yours is there now, you probably saw mine there. I just got it back last week. He put on a new hood and fenders.
Stay after him to give you an estimated finish date and then pester him once it comes an goes. (Don't tell him I said that)
If yours is there now, you probably saw mine there. I just got it back last week. He put on a new hood and fenders.
#8
Instructor
Thread Starter
Yes, you will need to keep on Greg. He does good work but he had my Corvette way too long this last time he worked on it.
Stay after him to give you an estimated finish date and then pester him once it comes an goes. (Don't tell him I said that)
If yours is there now, you probably saw mine there. I just got it back last week. He put on a new hood and fenders.
Stay after him to give you an estimated finish date and then pester him once it comes an goes. (Don't tell him I said that)
If yours is there now, you probably saw mine there. I just got it back last week. He put on a new hood and fenders.
#9
Instructor
Thread Starter
Maybe August before he is.. I told him I had a benefit Cruise in Aug. FWIW.
#10
Tech Contributor
#11
Instructor
Thread Starter
#13
Tech Contributor
Each time they had it quite a while, but the first 2 times I had more work done. This last time it was just to get a new hood and fenders painted and installed.
I started with this.
The 1st time, I had a wide booty done along with an aftermarket hood and front bumper.
Here is my car after the first trip.
Then I had an accident when my car slipped off of a jack. Passenger side rocker panel was damaged so I decided to go ahead and do the front conversion.
Here is my car after the second trip.
This last trip was to install a 427 takeoff hood and real Z06 carbon fiber fenders.
I don't have a photo of it yet. It's in my garage up on Race Ramps so I can install my ZR1 carbon fiber splitter and hopefully some side skirts.
Then I will be DONE.
,
#14
Le Mans Master
Oh, I see, looks good. My cars are the opposite, can't see the mods except for wheels.
I made a note of this place in case I ever need.
Ever go to the Cars & Coffee here in GSB? Think I might check it out next week.
I made a note of this place in case I ever need.
Ever go to the Cars & Coffee here in GSB? Think I might check it out next week.
#15
Tech Contributor
There is a good chance I will be there. Just depends on work and the weather.
#16
Instructor
Thread Starter
ncvette_1FUNRIDE
Finally got my girl back....
Quality of work is awesome !
Will not make March Cars and coffee but hope to see you April.
Finally got my girl back....
Quality of work is awesome !
Will not make March Cars and coffee but hope to see you April.
#17
Tech Contributor
#18
Instructor
Thread Starter
#19
Safety Car
#20
Tech Contributor