Driveshaft shop in Woodstock/ATL
#1
Racer
Thread Starter
Member Since: May 2005
Location: Canton GA
Posts: 360
Likes: 0
Received 0 Likes
on
0 Posts
Driveshaft shop in Woodstock/ATL
Hey guys, I'm doing the 4+3 to ZF conversion and when I pulled my driveshaft off the little bearings in the U joint went flying everywhere...
I need a good driveshaft shop that can repair that, and put the new yoke on for me as well. A balance check would be nice too!
Any good priced suggestions?
Thanks!
-Dwayne
I need a good driveshaft shop that can repair that, and put the new yoke on for me as well. A balance check would be nice too!
Any good priced suggestions?
Thanks!
-Dwayne
#4
Drifting
Member Since: Jan 2003
Location: An armed society is a polite society!
Posts: 1,946
Received 34 Likes
on
26 Posts
Cruise-In IV Veteran
St. Jude Donor '10
Hey man.
There is a place in Marietta called I believe "Marietta Drive Shaft". Its off of 41 near 575/5 interchange if I'm not mistaken. Look up in the phone book and you should find them. They do great work.
Oh yeah, Come on over to The Peach State Posse.
www.peachstateposse.com and register. Local group, with about 800 members on the forum. Someone over there can help.
There is a place in Marietta called I believe "Marietta Drive Shaft". Its off of 41 near 575/5 interchange if I'm not mistaken. Look up in the phone book and you should find them. They do great work.
Oh yeah, Come on over to The Peach State Posse.
www.peachstateposse.com and register. Local group, with about 800 members on the forum. Someone over there can help.
#10
Burning Brakes
Originally Posted by c5golfguy
Hey man.
There is a place in Marietta called I believe "Marietta Drive Shaft". Its off of 41 near 575/5 interchange if I'm not mistaken. Look up in the phone book and you should find them. They do great work.
Oh yeah, Come on over to The Peach State Posse.
www.peachstateposse.com and register. Local group, with about 800 members on the forum. Someone over there can help.
There is a place in Marietta called I believe "Marietta Drive Shaft". Its off of 41 near 575/5 interchange if I'm not mistaken. Look up in the phone book and you should find them. They do great work.
Oh yeah, Come on over to The Peach State Posse.
www.peachstateposse.com and register. Local group, with about 800 members on the forum. Someone over there can help.
If MDS does not suit your needs, try giving MTI Racing or Lamar Walden Automotive a call. The Posse's had good luck with them and they might be able to give you some ideas on a way ahead.
#12
Drifting
Member Since: Nov 2001
Location: Jacksonville Florida
Posts: 1,684
Likes: 0
Received 0 Likes
on
0 Posts
I suspect if LWA can't do it - they have a pretty complete machine shop, they will know who to contact. Ask for ROb.
And as others have said, come visit www.peachstateposse.com
Les
And as others have said, come visit www.peachstateposse.com
Les
Originally Posted by Thrak
Hey guys, I'm doing the 4+3 to ZF conversion and when I pulled my driveshaft off the little bearings in the U joint went flying everywhere...
I need a good driveshaft shop that can repair that, and put the new yoke on for me as well. A balance check would be nice too!
Any good priced suggestions?
Thanks!
-Dwayne
I need a good driveshaft shop that can repair that, and put the new yoke on for me as well. A balance check would be nice too!
Any good priced suggestions?
Thanks!
-Dwayne
#14
Team Owner
If you need u-joints. I'd call up http://www.tomsdifferentials.com/ and order some spicer u-joints without grease fitting as they're stronger. The spicers are much beefier than the brute force u-joints most places sell.
#15
Racer
Thread Starter
Member Since: May 2005
Location: Canton GA
Posts: 360
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by TarHeelDan2001
Is this R6MN Thrak? Who says the internet is a big place.....
haha.. yeah it is. The one and only!!
Whatchu doing over here man?
Didnt you see my thread about the Vette for R6 trade I made?
Last edited by Thrak; 09-13-2005 at 05:52 PM.
#16
Instructor
Member Since: Aug 2005
Location: Atlanta GA
Posts: 212
Likes: 0
Received 0 Likes
on
0 Posts
R6MN people everywhere, I tell you!
I missed the thread about your trade. I saw somewhere you got a new ride. Didn't realize it was a Vette. I just bought a '02 Black MN6 a few weeks ago, so I've started lurking here a little to educate myself.
The 6 is staying in the stable this weekend.... I'm headed to Barber for two days of fun on the Gixxer.
I missed the thread about your trade. I saw somewhere you got a new ride. Didn't realize it was a Vette. I just bought a '02 Black MN6 a few weeks ago, so I've started lurking here a little to educate myself.
The 6 is staying in the stable this weekend.... I'm headed to Barber for two days of fun on the Gixxer.
#20
Drifting
Originally Posted by ZO6Les
I suspect if LWA can't do it - they have a pretty complete machine shop, they will know who to contact. Ask for ROb.
And as others have said, come visit www.peachstateposse.com
Les
And as others have said, come visit www.peachstateposse.com
Les
i agree! Rob is the man!!
trust him with my life!