Cleveland, Ohio guys
09-16-2003, 03:58 PM
#1
Melting Slicks
Thread Starter
Cleveland, Ohio guys
Does anyone know of a good shop that will work on Corvette electrical problems? I am about to kick this thing down the driveway...... Preferably on the west, or southwest as I live in Olmsted Falls. I know of a shop in Russell that is pretty good but it is a long haul from here.
Refer to my previous post "Fusible Links" http://forums.corvetteforum.com/zerothread?id=648156
Thanks in advance.....
[Modified by KenSny, 2:36 PM 9/17/2003]
Refer to my previous post "Fusible Links" http://forums.corvetteforum.com/zerothread?id=648156
Thanks in advance.....
[Modified by KenSny, 2:36 PM 9/17/2003]
09-16-2003, 05:11 PM
#3
Melting Slicks
Thread Starter
Re: Cleveland, Ohio guys (Stewart's74)
Yeah, I was hoping he would, as he is Rocky River I think.....
See my post "Fusible Links" I'm good at following wiring diagrams and tracing stuff down, but this has got me up against the wall, I just can't find where the short is located..
See my post "Fusible Links" I'm good at following wiring diagrams and tracing stuff down, but this has got me up against the wall, I just can't find where the short is located..
09-17-2003, 08:31 AM
#5
Melting Slicks
Thread Starter
Re: Cleveland, Ohio guys (micks69)
Thanks anyway, but the car is completely dead, up on ramps, and in the garage. It's not going anywhere unless I get it towed. Planning on taking one more crack at it today as soon as I mow the grass....
09-17-2003, 09:59 AM
#8
Melting Slicks
Thread Starter
Re: Cleveland, Ohio guys (GDaina)
George - Thanks for the number, I'll call him this afternoon and see what's what.
Take a look at my post FUSIBLE LINKS and you'll see that I had to replace the link at the back of the fuse junction box. Had to remove a lot of stuff to get in there for one little wire. That will be going in soon, but of course that is not the problem, only the result of the problem so I was pulling all the fuses to isolate the circuits yesterday - no luck so far. Guess I'll put the link in and try activating the circuits one-by-one and see if it melts again.
Take a look at my post FUSIBLE LINKS and you'll see that I had to replace the link at the back of the fuse junction box. Had to remove a lot of stuff to get in there for one little wire. That will be going in soon, but of course that is not the problem, only the result of the problem so I was pulling all the fuses to isolate the circuits yesterday - no luck so far. Guess I'll put the link in and try activating the circuits one-by-one and see if it melts again.
09-17-2003, 12:43 PM
#9
Race Director
Member Since: Feb 1999
Location: In Dreams There Is Truth Ohio
Posts: 16,975
Likes: 0
Received 5 Likes
on
5 Posts
Re: Cleveland, Ohio guys (KenSny)
Guess I'll put the link in and try activating the circuits one-by-one and see if it melts again.
09-17-2003, 09:57 PM
#10
Melting Slicks
Member Since: Mar 2001
Location: Lake Villa IL
Posts: 3,365
Likes: 0
Received 5 Likes
on
3 Posts
Cruise-In IV Veteran
Cruise-In V Veteran
St. Jude Contributor
Re: Cleveland, Ohio guys (KenSny)
Ken, I have a guy in Akron, near downtown, who is good. But he takes his sweet time. :rolleyes: