Recieved Yoke for tremec - wish I could use it!
#1
Le Mans Master
Thread Starter
Recieved Yoke for tremec - wish I could use it!
Well I got my flat out gorgeous yoke from Mark Williams today - tried to mate it up with the tranney and - no joy - not even close :mad the C-6 rapid release yoke will NOT fit a TR-3550 which is a 28 spline output shaft - it fits the TKO which is a 31 spline output shaft.
My fault. I ordered the wrong one.
So I am back to where I began - where do I get a yoke for this tranny - Mark williams doesnt have a rapid release yoke C4 not C6 for this tranny.
Dagnabbit - this is going to push me back again.
Now I gotta ship it back - wait for a refund - before I can get the new yoke.
:mad :mad :mad
My fault. I ordered the wrong one.
So I am back to where I began - where do I get a yoke for this tranny - Mark williams doesnt have a rapid release yoke C4 not C6 for this tranny.
Dagnabbit - this is going to push me back again.
Now I gotta ship it back - wait for a refund - before I can get the new yoke.
:mad :mad :mad
#2
Team Owner
Re: Recieved Yoke for tremec - wish I could use it! (fauxrs)
Well I got my flat out gorgeous yoke from Mark Williams today - tried to mate it up with the tranney and - no joy - not even close :mad the C-6 rapid release yoke will NOT fit a TR-3550 which is a 28 spline output shaft - it fits the TKO which is a 31 spline output shaft.
My fault. I ordered the wrong one.
So I am back to where I began - where do I get a yoke for this tranny - Mark williams doesnt have a rapid release yoke C4 not C6 for this tranny.
Dagnabbit - this is going to push me back again.
Now I gotta ship it back - wait for a refund - before I can get the new yoke.
:mad :mad :mad
My fault. I ordered the wrong one.
So I am back to where I began - where do I get a yoke for this tranny - Mark williams doesnt have a rapid release yoke C4 not C6 for this tranny.
Dagnabbit - this is going to push me back again.
Now I gotta ship it back - wait for a refund - before I can get the new yoke.
:mad :mad :mad
#4
Drifting
Member Since: Feb 2002
Location: Manchester, Dead Center in the Middle of TN 25 miles to Jack Daniels,10 miles to Geo Dickle, and .8 mile from the Liquor Store at I-24 Exit 114
Posts: 1,987
Likes: 0
Received 2 Likes
on
2 Posts
St. Jude Donor '05
Re: Recieved Yoke for tremec - wish I could use it! (fauxrs)
I knew it was different but I thought you were getting the TKO as the rest of us did.
Have you checked with all of the Tremec suppliers for an applicable piece?
If worst comes to worst you can always get a driveshaft that will telescope. Just a thought , JIM :sad:
Have you checked with all of the Tremec suppliers for an applicable piece?
If worst comes to worst you can always get a driveshaft that will telescope. Just a thought , JIM :sad:
#5
Le Mans Master
Thread Starter
Re: Recieved Yoke for tremec - wish I could use it! (PROSOUTH)
Have you checked with all of the Tremec suppliers for an applicable piece?
Always willing to learn form other's experiences. Anyway, it was incredibly easy to find out the difference - in fact I did it on the phone while I was talking with the vendor.
I'm holding only myself out on this one, I usually do much more research on things such as this. Anyway, the vendor has already said - send it back we'll give you a full refund so no complaints there - just a bummer on the time delay involved.