Chassis is finished...what do you guys think?
#1
Melting Slicks
Thread Starter
Chassis is finished...what do you guys think?
The driveshaft is being painted and I'm still undecided on brakes, but I think the chassis is pretty much finished.
OK, build sheet.
LS1 out of '03 Vette with 19,000 miles
LS6 heads
Mugnuson supercharger with 3.1 pulley and 90mm inlet and TB
Lingenfelter cam 337/207 341/220
SS Hooker sidepipes modified to fit LS6 heads
Hoping for 500 RWHP
Street and Performance AC brackets
Z06 clutch
T56 Tranny out of '01 TA
18"X12.5" CCW's with 335/30/18 Micheline Pilot Sports in rear and 18x10" CCW's with 285/35/18's in front
SS fuel and brake lines
Black and Silver POR-15 paint
Rear end rebuilt by Van Steel with hardened spindles
3.55 rear ratio
Composite adjustable rear spring
QA1 adjustable semi coilovers
Steeroids rack and pinion
Offset TA
Van Steel tubular A-Arms
Custom built driveshaft
Probably going with Wilwood for brakes...just undecided on 6 or 4 piston and rotor size.
EDIT: Added photos: Body back on for a couple weeks before final bodywork which will be done on rotessirie.
OK, build sheet.
LS1 out of '03 Vette with 19,000 miles
LS6 heads
Mugnuson supercharger with 3.1 pulley and 90mm inlet and TB
Lingenfelter cam 337/207 341/220
SS Hooker sidepipes modified to fit LS6 heads
Hoping for 500 RWHP
Street and Performance AC brackets
Z06 clutch
T56 Tranny out of '01 TA
18"X12.5" CCW's with 335/30/18 Micheline Pilot Sports in rear and 18x10" CCW's with 285/35/18's in front
SS fuel and brake lines
Black and Silver POR-15 paint
Rear end rebuilt by Van Steel with hardened spindles
3.55 rear ratio
Composite adjustable rear spring
QA1 adjustable semi coilovers
Steeroids rack and pinion
Offset TA
Van Steel tubular A-Arms
Custom built driveshaft
Probably going with Wilwood for brakes...just undecided on 6 or 4 piston and rotor size.
EDIT: Added photos: Body back on for a couple weeks before final bodywork which will be done on rotessirie.
Last edited by SuprJames; 05-12-2007 at 03:42 PM.
#8
Safety Car
Wow!!!
#16
Melting Slicks
Originally Posted by Muddywaters
Looks like a classic dose of perfection to me... Muddy.
Last edited by rosslato; 10-30-2006 at 10:51 PM.
#20
Race Director
Member Since: Jan 2000
Location: Corsicana, Tx
Posts: 12,639
Received 1,908 Likes
on
930 Posts
2020 C2 of the Year - Modified Winner
2020 Corvette of the Year (performance mods)
C2 of Year Winner (performance mods) 2019
2017 C2 of Year Finalist
WOW...I gotta admit...I'm drooling too. Nice job!!
One question...did you make trans crossmember removable while you were there? It sure will be tough to pull trans later if you ever have to. Right now is the time to modify/replace crossmember...ask me how I know!!
JIM
One question...did you make trans crossmember removable while you were there? It sure will be tough to pull trans later if you ever have to. Right now is the time to modify/replace crossmember...ask me how I know!!
JIM