CorvetteForum - Chevrolet Corvette Forum Discussion

 
Page 1 of 3
1
2
3
Search: Posts Made By: VETTE077
Showing results 1 to 25 of 58
Search took 1.15 seconds.
Forum: C3 Tech/Performance
04-29-2014, 05:08 PM
Replies: 48
Views: 4,749
Posted By VETTE077

I have a 77 350- 350hhp 4spd put 3.55's cruises...

I have a 77 350- 350hhp 4spd put 3.55's cruises at 70mph about 3000 - 3100 RPM . Is good of the line. I think it would be screaming in 4th gear with anything lower. I like the 3.55's
Forum: C3 Tech/Performance
03-18-2010, 10:09 PM
Replies: 10
Views: 506
Posted By VETTE077

Thanks I beleive the squeek is in the rear, can't...

Thanks I beleive the squeek is in the rear, can't jack back of car up and run with the wheels hanging to hear it. I'll look closely at ujoints.
Forum: C3 Tech/Performance
03-18-2010, 08:03 PM
Replies: 10
Views: 506
Posted By VETTE077

Squeek squeek

When I first start driving I hear a squeek squeek that gets faster with speed or slower when I slow down. It lasts for maybe a mile or two and then its gone. If I let the car sit for awhile and drive...
Forum: C3 Tech/Performance
08-05-2009, 04:37 PM
Replies: 5
Views: 471
Posted By VETTE077

Thats kinda what I had in mind

Thats kinda what I had in mind
Forum: C3 Tech/Performance
08-05-2009, 02:38 PM
Replies: 5
Views: 471
Posted By VETTE077

I the stop is the answer but I dont have a welder

I the stop is the answer but I dont have a welder
Forum: C3 Tech/Performance
08-05-2009, 12:21 PM
Replies: 5
Views: 471
Posted By VETTE077

Another tire rub

Ok running 255/60s on 77 with original aluminum wheels and tires rub center of rear wheel well. Front suspension all new,instructions for lower ball joint say big headed bolt to front and has...
Forum: C3 Tech/Performance
04-20-2009, 01:39 PM
Replies: 8
Views: 1,586
Posted By VETTE077

The dome light on my 77 just came on when I was...

The dome light on my 77 just came on when I was driving then went out,then it would come on again and then out and stay on when I shut off the car and shut the door.Timer went bad.I took it out and...
Forum: C3 Tech/Performance
04-08-2009, 04:17 PM
Replies: 10
Views: 1,533
Posted By VETTE077

There is only one hole on some years. And don,t...

There is only one hole on some years. And don,t know if that will fill a Borg Warner trans. I think earlier years had Muncie trans.
Forum: C3 Tech/Performance
04-08-2009, 08:05 AM
Replies: 10
Views: 1,533
Posted By VETTE077

No holes for short throw shifter

Why is there no holes on the shift levers of a Borg Warner trans to change shifter linkage to short throw? 77 vette B/W T10 Can it be done and is it worth the trouble?
Forum: C3 Tech/Performance
02-07-2009, 03:11 PM
Replies: 4
Views: 563
Posted By VETTE077

Thanks for the pics. I quess it would be easier...

Thanks for the pics. I quess it would be easier to remove the cover to replace seals.What is that sheet metal piece is it a gauge to adjust the shifter? I been to simpsonville once my daughter played...
Forum: C3 Tech/Performance
02-06-2009, 10:33 AM
Replies: 4
Views: 563
Posted By VETTE077

4 speed side cover seals

Has anyone replaced shift shaft seals in side cover on BW 4 speed without taking the cover of when the trans is in the car.
Forum: C3 Tech/Performance
01-29-2009, 03:56 PM
Replies: 12
Views: 313
Posted By VETTE077

Thats good I just need to know if it is true that...

Thats good I just need to know if it is true that Richmond are generally noisy. I thought I was buying a good product. It was done at the Chevy dealer where i work and everything was set up right...
Forum: C3 Tech/Performance
01-29-2009, 03:16 PM
Replies: 12
Views: 313
Posted By VETTE077

Ring gear

GTR1999 What do you mean Richmond is a pita.I installed one in my car and cant seem to get the whine out of it when you let off the gas or at low speeds. Even changed pinion brg and still has a...
Forum: C3 Tech/Performance
10-04-2007, 09:17 PM
Replies: 24
Views: 6,553
Posted By VETTE077

Noisey

I changed mine 2 years ago from 3.36 to 3.55 with Richmond gears.Still noisey when letting off throttle or cruising slow speed thru town.Bearings were replaced,pinion brg replaced after setting...
Forum: C3 Tech/Performance
08-11-2007, 04:46 PM
Replies: 8
Views: 2,141
Posted By VETTE077

Will changing intake gaskets to the blocked...

Will changing intake gaskets to the blocked exhaust crossover improve anything at all? My car gets driven only in the warm weather months so starting is not a problem.I already have an insulator...
Forum: C3 Tech/Performance
08-11-2007, 03:15 PM
Replies: 8
Views: 2,141
Posted By VETTE077

Fuel Boiling?

In another post about intake gaskets somone mentioned they had gaskets with an open exhaust crossover which caused the fuel to boil.How do you know if the fuel is boiling?Does it spill out of the...
Forum: C3 Tech/Performance
06-28-2007, 09:19 PM
Replies: 21
Views: 1,832
Posted By VETTE077

Lars,Thanks for the reply,I was kinda confused...

Lars,Thanks for the reply,I was kinda confused with using a stiff spring yet wanting advance quicker.I understand.
Forum: C3 Tech/Performance
06-27-2007, 06:22 PM
Replies: 21
Views: 1,832
Posted By VETTE077

Lars,The MR G kit 929 I have it seems that the...

Lars,The MR G kit 929 I have it seems that the gold springs are stiffer than the black and silver.The balck are thin and less coils and the silver are easier to stretch than the gold.Does it make...
Forum: C3 Tech/Performance
06-27-2007, 07:01 AM
Replies: 3
Views: 547
Posted By VETTE077

Well the kit that I have the black springs are...

Well the kit that I have the black springs are the easiest to stretch then the silver and the gold is the harder on to stretch.The black one has less coils and is very thin.
Forum: C3 Tech/Performance
06-26-2007, 07:13 PM
Replies: 3
Views: 547
Posted By VETTE077

Mr.g 929g Curve Kit

I am a little confused on the springs .Lars said to use 2 gold springs on HEI units.Are the gold the heaviest springs in the kit.They seem to be heavier than the stock springs.Or does it make a...
Forum: C3 Tech/Performance
06-09-2007, 08:53 AM
Replies: 5
Views: 381
Posted By VETTE077

Edelbrock carb help

I have a problem with my carb stumbling at part throttle from a stop.Changed metering rods to get of popping in the exhaust from a lean condition.It worked and cars runs good.But iI still have a...
Forum: C3 Tech/Performance
06-08-2007, 08:52 PM
Replies: 4
Views: 1,981
Posted By VETTE077

I had a problem with my edelbrock when I let off...

I had a problem with my edelbrock when I let off the throttle I would get popping out the exhaust.Turned out to be the opposite it is caused by a lean condition called afterburn.Lars told me to go 2...
Forum: C3 Tech/Performance
04-23-2007, 04:16 PM
Replies: 3
Views: 951
Posted By VETTE077

Courtesy Light Timer Draining Battery

The timer on a 77 and some 78's looks like a silver flasher located behind the speedo and tach with a black wire soldered to it for a ground,a orange wire to fuse box,2 white wires connected to a...
Forum: C3 Tech/Performance
04-20-2007, 10:20 PM
Replies: 3
Views: 951
Posted By VETTE077

Courtesy light timer

Does a 77 definately have a courtesy light timer? If so where is it and what does it look like? Can it be bypassed if bad? My lights do not work with a timer now they just go off when you close the...
Forum: C3 Tech/Performance
03-29-2007, 04:26 PM
Replies: 3
Views: 360
Posted By VETTE077

Possessed

Just cruising down the road my courtesy lights decided to come on then go off and come on again seversl times,It wasn't like a loose connection they come on and go off.Both switches seem to be ok.Any...
Showing results 1 to 25 of 58
 
Page 1 of 3
1
2
3


 
Forum Jump

Trending Topics

All times are GMT -4. The time now is 08:59 PM.