CorvetteForum - Chevrolet Corvette Forum Discussion

 
Page 1 of 20
1
2
3
11
Last »
Search: Posts Made By: 90Indy
Showing results 1 to 25 of 496
Search took 1.72 seconds.
Forum: C4 Tech/Performance
10-23-2017, 09:05 PM
Replies: 11
Views: 894
Posted By 90Indy

Water In Gas?

I have heavily modded 90 Vert. The car has run great in the past but I have been fighting an erratic performance issue. The car acts as though it is not getting spark or fuel under a load. Some days...
Forum: C4 Tech/Performance
03-17-2015, 07:32 AM
Replies: 7
Views: 1,472
Posted By 90Indy

Thanks for the feedback. I am aware of the...

Thanks for the feedback. I am aware of the "keying" notch in the rotor and I am careful to install the rotor in the correct position.

Last night I went out and measured the distance the rotor...
Forum: C4 Tech/Performance
03-16-2015, 10:05 PM
Replies: 7
Views: 1,472
Posted By 90Indy

Carbon Bushing Melting The Distributor Cap

I have a 90 Auto and I have been having a problem with the distributor cap melting where the carbon bushing protrudes through the distributor cap and makes contact with the rotor. At first I was...
Forum: C4 Tech/Performance
08-16-2013, 01:10 PM
Replies: 4
Views: 1,175
Posted By 90Indy

DIC Flashing "INFL" -- No Seatbelt Light

I have a 90 Vert that about every year or so I have to remove the frame rail sensors for the SIR, clean the dirt/corrosion and reset the "INLF" light. Normally, I get the standard seat belt light and...
Forum: C4 Parts for Sale/Wanted
03-04-2013, 10:28 PM
Replies: 23
Views: 1,178
Posted By 90Indy

Let me know how to pay for the ECM and I will get...

Let me know how to pay for the ECM and I will get the funds to you.

Thanks
Forum: C4 Parts for Sale/Wanted
03-04-2013, 12:57 PM
Replies: 23
Views: 1,178
Posted By 90Indy

If you will sell me the one you were keeping for...

If you will sell me the one you were keeping for a spare for $60.00 shipped to Texas, I will take it.
Forum: C4 Parts for Sale/Wanted
03-02-2013, 10:39 PM
Replies: 23
Views: 1,178
Posted By 90Indy

Thanks for getting back with me. I will await...

Thanks for getting back with me. I will await your pics.

90Indy
Forum: C4 Parts for Sale/Wanted
03-02-2013, 09:16 AM
Replies: 23
Views: 1,178
Posted By 90Indy

Is this still for sale? I have a 90, does this...

Is this still for sale? I have a 90, does this unit work on any 90 or is it serial number specific? I do not know the model number of my ECM.

Thanks
Forum: C6 Tech/Performance
01-17-2013, 03:31 PM
Replies: 6
Views: 958
Posted By 90Indy

Burnt Distributor Cap

I am trying to determine why my distributor cap was badly burnt where the carbon button protrudes through onto the rotor. When I removed it, there was a burnt hole big enough to put my index finger...
Forum: C4 Tech/Performance
08-11-2012, 11:19 PM
Replies: 10
Views: 1,291
Posted By 90Indy

As far as collapsing duct work on my set up it...

As far as collapsing duct work on my set up it can't happen. The blower output goes directly into a 3.00"diameter aluminum tube bend which is welded to an aluminum Vortec plenum. The plenum is...
Forum: C4 Tech/Performance
08-11-2012, 07:41 PM
Replies: 10
Views: 1,291
Posted By 90Indy

As far as collapsing duct work on my set up it...

As far as collapsing duct work on my set up it can't happen. The blower output goes directly into a 3.00"diameter aluminum tube bend which is welded to an aluminum Vortec plenum. The plenum is...
Forum: C4 Tech/Performance
08-11-2012, 08:13 AM
Replies: 10
Views: 1,291
Posted By 90Indy

I am thinking along those same lines. It seems to...

I am thinking along those same lines. It seems to me, the 2 bar MAP signal is not being received, therefore no increase in fueling. However, my wife and I are celebrating our wedding anniversary this...
Forum: C4 Tech/Performance
08-10-2012, 08:07 AM
Replies: 10
Views: 1,291
Posted By 90Indy

Car Not Performing Under Boost -- Help!

I have developed a problem with my 90 Vert with a 383 running 11 psi of boost. The engine was built from the start for FI so it is low compression (8.4:1), ProCharger P600B, forged internals, 60...
Forum: C4 Tech/Performance
05-08-2012, 01:28 PM
Replies: 1
Views: 404
Posted By 90Indy

The idle problem has been solved. It seems the...

The idle problem has been solved. It seems the ECM technician installed the factory prom in backwards. AES finally contacted me today and told me to remove my Moates board and flip the factory prom...
Forum: C4 Tech/Performance
05-07-2012, 10:57 PM
Replies: 1
Views: 404
Posted By 90Indy

90 Vert ECM Problems

Here is my story:
Sent my ECM to Automotive Electrical Solutions (AES) for diagnostic inspection and updating by incorporating the applicable GM Service Bulletins. At the time I sent it to them, the...
Forum: C4 Tech/Performance
02-29-2012, 09:27 PM
Replies: 3
Views: 1,709
Posted By 90Indy

Today I removed the red connector from the back...

Today I removed the red connector from the back of the ECM and checked the continuity between the female end of the connector with pin F on the ALDL as well as visually checking the male pins coming...
Forum: C4 Tech/Performance
02-28-2012, 10:29 PM
Replies: 3
Views: 1,709
Posted By 90Indy

No Torque Converter Lockup After Dyno

I took my 90 Auto to have it dyno-tuned after I installed an 11 psi pulley on the blower. I had been driving on the tune for over a year without any lock-up issues. However, after the tune the...
Forum: C4 Tech/Performance
02-24-2012, 08:29 AM
Replies: 5
Views: 1,629
Posted By 90Indy

Great ideas, thanks. I guess I was too focused on...

Great ideas, thanks. I guess I was too focused on the dyno run to think outside the box. When I get a chance this week end I will do some checking.

Thanks again,

90Indy
Forum: C4 Tech/Performance
02-23-2012, 09:18 PM
Replies: 5
Views: 1,629
Posted By 90Indy

90 With Torque Converter Lock-Up Issues

I recently had my 90 on the dyno. As far as the auto transmission shifting and torque converter locking up, all has worked well since I rebuilt both the engine and transmission around 10,000 miles...
Forum: C4 Tech/Performance
11-16-2011, 10:50 PM
Replies: 21
Views: 1,089
Posted By 90Indy

I have modded several cars and I have learned...

I have modded several cars and I have learned sometimes the hard ($$) way, three things to consider before starting down the modding road.

1) Your budget.
2) Your mechanical skill level.
3) Your...
Forum: C4 General Discussion
04-29-2011, 10:57 PM
Replies: 11
Views: 1,345
Posted By 90Indy

Caliper Covers - Experience Anyone?

I have been debating for some time whether or not I wanted to paint my calipers and what color to chose. While doing some research I came across some GM licensed caliper covers for around $180.00. I...
Forum: C4 Parts for Sale/Wanted
02-01-2011, 10:07 PM
Replies: 3
Views: 495
Posted By 90Indy

I am interested but it looks like several of the...

I am interested but it looks like several of the bolt holes are oversized with a burr around the edge. Is this correct or does it just appear that way due to the angle?

90Indy
Forum: C4 Tech/Performance
11-26-2010, 10:26 PM
Replies: 12
Views: 3,331
Posted By 90Indy

I guess I keep being a bubble buster on boosting...

I guess I keep being a bubble buster on boosting a stock L98. With my experience with boosting a stock L98, I would highly advise against it. There are just too many variables with forced induction...
Forum: C4 Tech/Performance
11-10-2010, 09:42 PM
Replies: 4
Views: 2,881
Posted By 90Indy

I do not have any experience with the ProCharger...

I do not have any experience with the ProCharger D-1 but I did purchase their smaller P600B kit and found it to be much more time consuming to install than they led me to believe. Also, knowing what...
Forum: C4 Tech/Performance
08-19-2010, 10:41 PM
Replies: 2
Views: 729
Posted By 90Indy

Will do sir.

Will do sir.
Showing results 1 to 25 of 496
 
Page 1 of 20
1
2
3
11
Last »


 
Forum Jump

Trending Topics

All times are GMT -4. The time now is 02:45 PM.