CorvetteForum - Chevrolet Corvette Forum Discussion

 
Page 1 of 4
1
2
3
Last »
Search: Posts Made By: 1BAD88
Showing results 1 to 25 of 82
Search took 1.23 seconds.
Forum: C4 Tech/Performance
08-03-2011, 09:21 AM
Replies: 5
Views: 1,168
Posted By 1BAD88

The car is just sitting still idling no load. It...

The car is just sitting still idling no load. It gets code 44 after idling for about 3 minutes or more in closed loop.

I was thinking that maybe there is too much oscillation and there might be a...
Forum: C4 Tech/Performance
08-02-2011, 10:30 PM
Replies: 5
Views: 1,168
Posted By 1BAD88

Lean O2 code with BLM 122 at idle

What would cause this issue? O2 voltage swings between 220 and 840 mv at idle and BLM is steady at 122. I still get error code 44.

Should I add more timing? It's at about 20* total at idle.
...
Forum: C4 Tech/Performance
07-25-2011, 11:04 PM
Replies: 7
Views: 1,033
Posted By 1BAD88

I found a good guide for tuning $32B on Craig...

I found a good guide for tuning $32B on Craig Moates site tonight and have been studying that. It looks like I had the BPW Calc box checked when I was modifying the BPW table. I'm going to get...
Forum: C4 Tech/Performance
07-25-2011, 07:36 PM
Replies: 7
Views: 1,033
Posted By 1BAD88

I emailed the files to the address given. -J

I emailed the files to the address given.

-J
Forum: C4 Tech/Performance
07-25-2011, 08:36 AM
Replies: 7
Views: 1,033
Posted By 1BAD88

Could you clarify this? From how it sounds, I...

Could you clarify this? From how it sounds, I may have had this backwards. If the box is checked is it using the BPW - Load vs Coolant Temp table or the MAF tables?

Here's my mods:

Racetronix...
Forum: C4 Tech/Performance
07-24-2011, 11:19 PM
Replies: 7
Views: 1,033
Posted By 1BAD88

BPW and SA Calculations ($32B)

I am at a loss. The people in this forum have been a huge amount of help in the past and I hope someone can throw me a line on this one.

When BPW Calibration method is unchecked in $32B, what...
Forum: C4 Parts for Sale/Wanted
06-30-2011, 04:38 PM
Replies: 5
Views: 293
Posted By 1BAD88

I think you are looking for the TPI intake from...

I think you are looking for the TPI intake from Skoggin Dickey ~$400 new as I recall
Forum: C4 Parts for Sale/Wanted
06-14-2011, 08:49 AM
Replies: 4
Views: 490
Posted By 1BAD88

Sold

Sold
Forum: C4 Parts for Sale/Wanted
06-13-2011, 08:14 PM
Replies: 4
Views: 490
Posted By 1BAD88

PM replied

PM replied
Forum: C4 Parts for Sale/Wanted
06-13-2011, 09:13 AM
Replies: 4
Views: 490
Posted By 1BAD88

I snapped a couple of pictures ...

I snapped a couple of pictures

http://forums.corvetteforum.com/picture.php?albumid=17906&pictureid=85107

http://forums.corvetteforum.com/picture.php?albumid=17906&pictureid=85105
Forum: C4 Parts for Sale/Wanted
06-12-2011, 10:37 AM
Replies: 4
Views: 490
Posted By 1BAD88

Late C4 K&N Air Filter

I have a K&N air filter for a late C4 (PN 33-2035) with less than 500 miles on it. It is in excellent shape and in the original box. $70 shipped to continental US (lower 48).
Forum: C4 Parts for Sale/Wanted
06-06-2011, 09:00 AM
Replies: 2
Views: 347
Posted By 1BAD88

How much for just the filter and lid?

How much for just the filter and lid?
Forum: C4 Parts for Sale/Wanted
05-05-2011, 02:33 PM
Replies: 76
Views: 6,292
Posted By 1BAD88

I've got some MN plates rolling around if you are...

I've got some MN plates rolling around if you are still collecting.

-J
Forum: C4 Parts for Sale/Wanted
04-24-2011, 09:50 AM
Replies: 1
Views: 617
Posted By 1BAD88

L-98 113 Heads and other stuff

Assembled stock L-98 heads, had them cleaned and inspected. They came off a car with 70k miles on it. I will include the stock rockers too. - $425

I have other parts from my upgrades too if...
Forum: C4 Parts for Sale/Wanted
04-23-2011, 10:14 AM
Replies: 7
Views: 689
Posted By 1BAD88

PM'd you - Are the rockers still available?

PM'd you - Are the rockers still available?
Forum: C4 Tech/Performance
04-23-2011, 10:04 AM
Replies: 24
Views: 2,263
Posted By 1BAD88

Cuisinartvette is correct, I'm going N/A. Don't...

Cuisinartvette is correct, I'm going N/A. Don't have deep enough pockets for FI. Stock CR was 9.5:1 new CR will be 9.4:1 with the Fel-Pro 1094 gasket, not that much of a loss. I plan to replace...
Forum: C4 Parts for Sale/Wanted
04-23-2011, 09:19 AM
Replies: 2
Views: 365
Posted By 1BAD88

I'm also looking to replace mine, I was browsing...

I'm also looking to replace mine, I was browsing McMaster and it looks like they are probably Viton or Fluorosilicone, as those are the two options for clear o-rings.

<EDIT> Found this: Viton...
Forum: C4 Tech/Performance
04-22-2011, 06:35 PM
Replies: 24
Views: 2,263
Posted By 1BAD88

Thank you everyone for your advice. I ended up...

Thank you everyone for your advice. I ended up with a regular pair of 195/1040's. A big thanks goes to Rick for all of his help. Now I just have to wait until the end of may.
Forum: C4 Tech/Performance
04-19-2011, 10:37 PM
Replies: 24
Views: 2,263
Posted By 1BAD88

Perhaps I'm thinking about this upside down. ...

Perhaps I'm thinking about this upside down. What about changing the pistons, rings, and rod bolts? This way the heads could be used as is and would have more options for future builds. Any other...
Forum: C4 Tech/Performance
04-18-2011, 12:09 AM
Replies: 24
Views: 2,263
Posted By 1BAD88

Gregg, You bring up an interesting point...

Gregg,

You bring up an interesting point though, with the 56cc chambers you were able to use a thicker head gasket that is generally considered to be a more reliable option.

-J
Forum: C4 Tech/Performance
04-17-2011, 06:48 PM
Replies: 24
Views: 2,263
Posted By 1BAD88

So if I have them milled to 60cc's and use a...

So if I have them milled to 60cc's and use a 0.028" head gasket it looks like I can get to 9.63:1

4" bore, 3.48" stroke, 4.03" head gasket diameter, 0.028" compressed gasket, 60cc chamber, 12 cc...
Forum: C4 Tech/Performance
04-17-2011, 05:44 PM
Replies: 23
Views: 1,026
Posted By 1BAD88

It isn't possible to have the dizzy 1 tooth off,...

It isn't possible to have the dizzy 1 tooth off, is it? It only goes in 2 ways because it has a roll pin that engages the oil pump. So maybe 180 degrees off but not 1 tooth.
Forum: C4 Tech/Performance
04-17-2011, 05:40 PM
Replies: 24
Views: 2,263
Posted By 1BAD88

Upgrading to AFR 195's

I am hoping to move to AFR 195's for my 88 with a Super Ram, headers, 222 cam, stock bottom end and pistons, etc. and have a couple of questions.

#1 What is the best way to deal with the loss in...
Forum: C4 Parts for Sale/Wanted
04-13-2011, 10:58 PM
Replies: 2
Views: 429
Posted By 1BAD88

===> SOLD AND SHIPPED <=== Thank you...

===> SOLD AND SHIPPED <===

Thank you Bill!
Forum: C4 Parts for Sale/Wanted
04-12-2011, 09:41 PM
Replies: 2
Wtb
Views: 290
Posted By 1BAD88

I've got the AIR equipment from my 88 if you're...

I've got the AIR equipment from my 88 if you're interested. PM me if you want and I can get you pictures.
Showing results 1 to 25 of 82
 
Page 1 of 4
1
2
3
Last »


 
Forum Jump

Trending Topics

All times are GMT -4. The time now is 02:18 PM.