CorvetteForum - Chevrolet Corvette Forum Discussion

 
Page 1 of 20
1
2
3
11
Last »
Search: Posts Made By: grayhook
Showing results 1 to 25 of 497
Search took 1.67 seconds.
Forum: C3 Tech/Performance
07-06-2013, 04:50 PM
Replies: 10
Views: 2,110
Posted By grayhook

You must do something with #1. See in switch were...

You must do something with #1. See in switch were both line 91 and 92 go to ground in low speed, and by removing one or the other get's high speed and park. and both ground being low speed.
Forum: C3 Tech/Performance
07-06-2013, 01:45 PM
Replies: 10
Views: 2,110
Posted By grayhook

Yes I forgot to add that, thanks. No need to...

Yes I forgot to add that, thanks.
No need to remove ground from #1 after park thow. See switch line 91 to ground when off.
Forum: C3 Tech/Performance
07-06-2013, 12:38 PM
Replies: 8
Views: 666
Posted By grayhook

Your lights will work with only 9 lbs. vac at...

Your lights will work with only 9 lbs. vac at idle.
I have about the same 9 lbs. with my setup. (355 with a Holly sysm. max kit 425hp)
I had a problem with mine and after looking it over I found a...
Forum: C3 Tech/Performance
07-06-2013, 12:02 PM
Replies: 10
Views: 2,110
Posted By grayhook

Try the Tech video file on Willcox site. Shows...

Try the Tech video file on Willcox site.
Shows 12v going to #2 and ground to case, motor will go into run-on. Add ground to #3 and will park. Add ground to #1 and #3 get high speed. remove ground...
Forum: C3 Tech/Performance
06-25-2013, 08:35 AM
Replies: 3
Views: 633
Posted By grayhook

I have a 79 that had the small spoiler on it when...

I have a 79 that had the small spoiler on it when I got it. Adding the 3pc. Indy spoiler helped a lot with hwy speed cooling. The 79's came with the 3pc. so that's why I went with it.
Forum: C3 Tech/Performance
06-02-2013, 11:11 AM
Replies: 10
Views: 1,370
Posted By grayhook

I think you will find there is good bit of meet...

I think you will find there is good bit of meet there around those holes, just clean it out (may have to drill out) and re-tap it to the next size up. If not, there are thread inserts out there.
Forum: C3 Tech/Performance
05-29-2013, 08:31 AM
Replies: 8
Views: 1,042
Posted By grayhook

Glad to help. And good luck with the new 82!

Glad to help. And good luck with the new 82!
Forum: C3 Tech/Performance
05-27-2013, 10:46 PM
Replies: 8
Views: 1,042
Posted By grayhook

There is a hole in the cowl to get to a tab on...

There is a hole in the cowl to get to a tab on the latch you have to push to release. I'm sure if you do a search you'll find a few post on this. your cable has broke or came off on one side sounds...
Forum: C3 General
07-28-2010, 10:46 PM
Replies: 2
Views: 344
Posted By grayhook

I'm in jackson, Florence is just about 15min....

I'm in jackson, Florence is just about 15min. away from me.
I can give it a look/snap a pic for ya.
Dont know a lot about the c6's. more of a c3 guy.;) but glad to help out if i can.
Forum: C3 Tech/Performance
06-20-2010, 07:54 AM
Replies: 5
Views: 547
Posted By grayhook

The L82 allso came with a aluminium intake. ...

The L82 allso came with a aluminium intake.
forgive the PO who did the yellow on the valve covers:ack:
http://forums.corvetteforum.com/picture.php?pictureid=53928&albumid=11448&dl=1274918532&thumb=1
Forum: C3 Tech/Performance
06-09-2010, 08:25 PM
Replies: 13
Views: 1,115
Posted By grayhook

Help with the hood, scribe a line around the...

Help with the hood, scribe a line around the bracket, drill a small hole in the bracket threw to hood, use bit in the hole when reinstalling to line hood back up to real close.
Forum: C3 Tech/Performance
06-06-2010, 12:31 PM
Replies: 11
Views: 1,565
Posted By grayhook

Not a good sine. yes, pull the intake, see if you...

Not a good sine. yes, pull the intake, see if you have a wiped lobe on the cam.
When i got my 79 it had a miss a good tune up didnt get out, so i pulled my valve covers and found one pushrod gone...
Forum: C3 Tech/Performance
05-18-2010, 08:53 AM
Replies: 3
Views: 830
Posted By grayhook

I have never done this kind of swap, but think...

I have never done this kind of swap, but think it'ed be no problem.
I have seen the 79/82 dash in a 74 i think it was.
The only problem i can think of is if the 80 has electric seats, thay wont...
Forum: C3 General
10-20-2007, 03:10 PM
Replies: 9
Views: 762
Posted By grayhook

My 79 L82 with CR 4 spd(only 3494), Yellow(only...

My 79 L82 with CR 4 spd(only 3494), Yellow(only 2357), no power locks, no power windows, has a/c and tilt-telescopic steering wheel. For a 79 i bet thats a very rare combo.
But you wont get any...
Forum: C3 Tech/Performance
10-13-2007, 12:14 AM
Replies: 14
Views: 1,989
Posted By grayhook

Fire that camera man Brett! :lol: i Got one...

Fire that camera man Brett! :lol:

i Got one too. 355 with Holley sys. max kit.

http://media.putfile.com/Movie-0002-47-82
Forum: C3 Tech/Performance
08-19-2007, 09:45 PM
Replies: 27
Views: 3,159
Posted By grayhook

I snaged a set of Van Steel's loaded offset...

I snaged a set of Van Steel's loaded offset trailing arms a few year's ago. The off set just get's you more room for tire, keeps the same location of the wheel, thus same hafe shafts.
When i opened...
Forum: C3 Tech/Performance
04-19-2007, 11:00 PM
Replies: 23
Views: 2,161
Posted By grayhook

A while back there was a guy use'n a few wraps of...

A while back there was a guy use'n a few wraps of Aluminum Tape around the inside end to seal his up.:thumbs:
Forum: C3 Tech/Performance
04-11-2007, 02:14 PM
Replies: 13
Views: 798
Posted By grayhook

Holley site says... Lunati Cam spec's intake...

Holley site says...
Lunati Cam spec's
intake lift .488°
Exhaust lift .510°
intake duration @.050: 234°
exhaust duration @.050: 244°
intake valve lobe centerline 107°
lobe seperation 112°
...
Forum: C3 Tech/Performance
04-10-2007, 08:28 PM
Replies: 13
Views: 798
Posted By grayhook

I'm get'n around 9 on the vacuum gauge and...

I'm get'n around 9 on the vacuum gauge and headlights work fine.
Try Summit part # HLY-300-503-1 (it's up about $400 from a few years ago when i got mine)

idle vid
...
Forum: C3 Tech/Performance
04-10-2007, 02:58 PM
Replies: 13
Views: 798
Posted By grayhook

Yes all Holley, Street Dominator Intake, 20º...

Yes all Holley, Street Dominator Intake, 20º Aluminum Cylinder Heads (Straight Plug). Allso has a Lunati cam, Lifters, and Timing Set and head bolts
Nice kit for the money.
I had a few say the cam...
Forum: C3 Tech/Performance
04-09-2007, 02:37 PM
Replies: 13
Views: 798
Posted By grayhook

The Holley SysteMAX Engine Kit did me good. With...

The Holley SysteMAX Engine Kit did me good. With a holley 750 dp and holley's aircleaner it has clearance for my stock hood, and cam has a noticiable thumpy idle.
...
Forum: C3 Tech/Performance
03-13-2007, 12:32 AM
Replies: 7
Views: 604
Posted By grayhook

Links here on the left side, Zip's, Corvette...

Links here on the left side, Zip's, Corvette Central, Ecklers, Willcox...
If the weatherstrip is bad i'ed look closer to be sure thats all it need before buying it.
Forum: C3 Tech/Performance
03-13-2007, 12:09 AM
Replies: 7
Views: 604
Posted By grayhook

Yes, thay make a kit with all the weather...

Yes, thay make a kit with all the weather stripping in it. I have not done the job yet, but know it can be nasty trying to get all the old glue off.(Think theres a spray that will help remove it.)
...
Forum: C3 Tech/Performance
02-13-2007, 08:50 PM
Replies: 18
Views: 6,374
Posted By grayhook

Yes, do you? this is the key thing i'ed say. ...

Yes, do you? this is the key thing i'ed say.

You got that right!:thumbs:

But there is nothing like do'n it yourself!
Just do it right the first time.:lol:
I did it, 355 short block from a...
Forum: C3 General
10-18-2006, 01:51 PM
Replies: 7
Views: 386
Posted By grayhook

Hhmm, try agen then... ...

Hhmm, try agen then...

http://f5.putfile.com/5/13120520626.jpg

If that dont work, try here...
http://www.putfile.com/grayhook
Showing results 1 to 25 of 497
 
Page 1 of 20
1
2
3
11
Last »


 
Forum Jump

Trending Topics

All times are GMT -4. The time now is 05:52 AM.