CorvetteForum - Chevrolet Corvette Forum Discussion

Search: Posts Made By: FOR PLA
Showing results 1 to 16 of 16
Search took 1.12 seconds.
Forum: C4 Tech/Performance
04-13-2016, 06:31 PM
Replies: 49
Views: 5,361
Posted By FOR PLA

Rebleed each caliper in proper order then reset...

Rebleed each caliper in proper order then reset bias switch. You have air in system some where.
Forum: C4 Tech/Performance
04-13-2016, 05:52 PM
Replies: 49
Views: 5,361
Posted By FOR PLA

I am assuming bleeding at each wheel caliper was...

I am assuming bleeding at each wheel caliper was done properly. Then move the pressure switch to center.
Forum: C4 Tech/Performance
04-13-2016, 05:45 PM
Replies: 49
Views: 5,361
Posted By FOR PLA

Centering the pressure bias piston should be the...

Centering the pressure bias piston should be the last step. Move it to center with small screwdriver and replace switch. Job done.
Forum: C4 Tech/Performance
04-12-2016, 05:58 PM
Replies: 49
Views: 5,361
Posted By FOR PLA

The switch needs to be removed and once removed ...

The switch needs to be removed and once removed you can access the pressure equalization piston. This small piston needs to be centered in the master cylinder housing. Bleeding moves the bias...
Forum: C4 Tech/Performance
09-08-2004, 10:07 PM
Replies: 25
Views: 4,096
Posted By FOR PLA

Sounds like ECM to me. I had the very same...

Sounds like ECM to me. I had the very same problem.New EMC and problem solved
Forum: C4 General Discussion
09-07-2004, 09:56 PM
Replies: 14
Views: 1,942
Posted By FOR PLA

:iagree: I always jack it up in the center and...

:iagree: I always jack it up in the center and place jackstands at the marked jacking points. Works great
Forum: Wheels & Tires
08-12-2004, 10:57 PM
Replies: 8
Views: 454
Posted By FOR PLA

Thanks this the kind of info I needed. :cheers: ...

Thanks this the kind of info I needed. :cheers: :seeya
Forum: Wheels & Tires
08-06-2004, 11:45 PM
Replies: 8
Views: 454
Posted By FOR PLA

metal valve stem????

Just wondering it anyone has experience with metal valve stems.Thinking of installing these on new wheels. I am looking for info PRO and CON thanks.
Forum: C4 Tech/Performance
08-04-2004, 10:09 PM
Replies: 6
Views: 6,432
Posted By FOR PLA

I've replaced my IAC three times in 6000 miles....

I've replaced my IAC three times in 6000 miles. Each time the new IAC [a c delco] solved the problem for a few months.The last time it went kapoot on a road trip in the mountians 'not much fun'...
Forum: C4 Tech/Performance
07-21-2004, 11:12 PM
Replies: 9
Views: 2,448
Posted By FOR PLA

:iagree: IAC is the most likley cause

:iagree: IAC is the most likley cause
Forum: C4 Tech/Performance
08-19-2003, 11:40 PM
Replies: 10
Views: 1,342
Posted By FOR PLA

Re: air conditioning blows out of the defroster (Shadoejack)

Sounds like a bad vacuum check valve to me.Easy fix hope this your problem. :)
Forum: C4 Tech/Performance
08-14-2003, 02:18 PM
Replies: 47
Views: 14,548
Posted By FOR PLA

Re: Is 160* Thermostat too Cold? (ELEVENS)

:iagree: I have found that in cooler weather the engine doesn't warm up enough. Never gets above 160. Try 180 thermosat wont matter in summer temps will be the same but in cold temps will be better....
Forum: C4 General Discussion
08-13-2003, 11:28 AM
Replies: 27
Views: 4,418
Posted By FOR PLA

Re: L98 engine owners, do you use the longer oil filter? (Southern Comfort)

Longer filter. Holds more oil (slightly) much easer to reach for remove and install :)
Forum: C4 General Discussion
08-10-2003, 11:40 PM
Replies: 22
Views: 1,052
Posted By FOR PLA

Re: Need advice on muffler elims (84FromHell)

:iagree: Just GREAT sound
Forum: C4 General Discussion
08-10-2003, 11:17 PM
Replies: 19
Views: 628
Posted By FOR PLA

Re: Dirty Rear Ends..... (Beautiful Beast)

:iagree:
Showing results 1 to 16 of 16


 
Forum Jump

Trending Topics

All times are GMT -4. The time now is 10:41 PM.