CorvetteForum - Chevrolet Corvette Forum Discussion

Search: Posts Made By: thatchh
Showing results 1 to 10 of 10
Search took 1.24 seconds.
Forum: C7 Tech/Performance
04-12-2018, 03:05 AM
Replies: 30
Views: 4,962
Posted By thatchh

So what PSI is recommended for track days?

So what PSI is recommended for track days?
Forum: C7 Tech/Performance
04-11-2018, 02:08 AM
Replies: 2
Views: 4,318
Posted By thatchh

Horrible Engine Noise

My 2015 Z51 M7 makes a similar noise. What was the outcome?
Thanks
Forum: C7 General Discussion
10-18-2017, 12:32 AM
Replies: 7
Views: 3,371
Posted By thatchh

No help

I took mine (2015) to a dealer today and got a no fault found. I tried it in the parking lot before I left, and they came back to the previous setting. Next several times I used reverse, they only...
Forum: C5 Tech
01-05-2005, 02:15 AM
Replies: 7
Views: 493
Posted By thatchh

My 98 did the same thing. If I wound it up and...

My 98 did the same thing. If I wound it up and didn't get it hooked up some times, it would just spin and bake. Always seemed to be ok after it cooled down. Nasty smell, though. I am replacing mine...
Forum: C5 Tech
01-05-2005, 02:05 AM
Replies: 9
Views: 432
Posted By thatchh

Sometimes the computer takes two start cycles to...

Sometimes the computer takes two start cycles to remove a fault message once the fault goes away. That may be why you didn't see it when you started today. Try shutting off the car and restarting...
Forum: C5 Tech
12-30-2004, 02:49 PM
Replies: 13
Views: 20,681
Posted By thatchh

Pilot bearing removal tip

I have been fighting a pilot bearing in the crank that would not budge. I broke the tips off a screw type puller. I bought a slide hammer puller and it didn't do squat. I tried using a reciprocating...
Forum: C5 Tech
12-21-2004, 03:30 PM
Replies: 2
Views: 567
Posted By thatchh

manual transmission leak

Hi Guys,
I have a 98 6 speed (sitting out of the car) that is dripping at the seam between the rear portion of the case (about 6" long) and the main part of the case. I can see that it was sealed...
Forum: C5 Tech
07-06-2004, 07:45 PM
Replies: 1
Views: 244
Posted By thatchh

connector identification

During inspection of recent repair, I disovered a disconnected connector. It looks like it's been that way for a while. My car is a 98 coupe. The connector pair is in the front end just inboard of...
Forum: C5 Tech
11-25-2003, 07:05 PM
Replies: 14
Views: 3,467
Posted By thatchh

Re: Rear wheel bearing/hub assy-1998 (84bronzevette)

Just call your local bearing dealer and give them the Timken part #. (available in the installation guide in the archives). I got mine from Kaman Bearings for about $150 per corner.
Thatch
Forum: C5 Tech
08-14-2003, 12:47 PM
Replies: 0
Views: 836
Posted By thatchh

Traction Control Problem

Hi Guys,
I have a 98 Coupe with Z51 and no active handling, just the standard traction control. It does have a Carroll supercharger setup and ~450 hp.
I have experienced an intermittent problem...
Showing results 1 to 10 of 10


 
Forum Jump

Trending Topics

All times are GMT -4. The time now is 07:26 PM.