CorvetteForum - Chevrolet Corvette Forum Discussion

 
Page 1 of 11
1
2
3
Last »
Search: Posts Made By: 11Black-GS
Showing results 1 to 25 of 252
Search took 1.04 seconds.
Forum: C6 Corvette General Discussion
09-08-2016, 10:23 AM
Replies: 16
Views: 3,505
Posted By 11Black-GS

I didn't drill any holes. I removed one of the...

I didn't drill any holes. I removed one of the screws (the ones that hold the aluminum cover plate) that is above the xpipe, and put a cable clamp on, ran the o2 sensor wire through it, then put the...
Forum: C6 Corvette General Discussion
09-07-2016, 09:47 PM
Replies: 16
Views: 3,505
Posted By 11Black-GS

I installed headers myself and didn't raise the...

I installed headers myself and didn't raise the engine. You will have to disconnect the dry sump line and move out of the way to get the headers up on the passenger side. I have kooks headers and...
Forum: C6 Tech/Performance
09-07-2016, 04:18 PM
Replies: 8
Views: 878
Posted By 11Black-GS

It is easier to measure RWHP, but for sake of...

It is easier to measure RWHP, but for sake of conversation, I tend to speak in terms of crank HP. Perhaps I should be asking what will get me to 4xx RWHP, but I figured it didn't matter as most...
Forum: C6 Tech/Performance
09-07-2016, 04:12 PM
Replies: 8
Views: 878
Posted By 11Black-GS

There is no rhyme or reason, I just want to be...

There is no rhyme or reason, I just want to be above the 500 HP mark if I could do it with bolt ons. :D

I have looked at different cams and the mildest one I seen would still probably get me over...
Forum: C6 Tech/Performance
09-06-2016, 09:41 PM
Replies: 8
Views: 878
Posted By 11Black-GS

Already have Headers, Catback, & Tune...is CAI best bang for buck to be above 500hp?

Is there anything else that would be better to install than a CAI? Fast Intake maybe? My goal is to be slightly above 500HP (at the crank). I realize I can easily do that with a mild cam, but Im...
Forum: C6 Corvette General Discussion
03-25-2016, 02:04 PM
Replies: 17
Views: 1,463
Posted By 11Black-GS

I just installed Kooks headers myself and started...

I just installed Kooks headers myself and started it up yesterday. It sounds like a monster! I only revved it to 2K and will be getting a tune on Tuesday so that I can drive it without worrying of a...
Forum: C6 Corvette General Discussion
03-14-2016, 08:40 AM
Replies: 8
Views: 1,766
Posted By 11Black-GS

I have a manual. I did notice the line is...

I have a manual.

I did notice the line is connected to a bracket. I am going to try to undo the bracket and see if it helps. The only problem is that portion of line connected is metal so I still...
Forum: C6 Corvette General Discussion
03-13-2016, 06:25 PM
Replies: 8
Views: 1,766
Posted By 11Black-GS

What you guys are referring to is what is needed...

What you guys are referring to is what is needed to be done when installing the passenger side. I already removed oil lines and have the passenger side header installed.

I have watched the Hinson...
Forum: C6 Corvette General Discussion
03-13-2016, 03:20 PM
Replies: 8
Views: 1,766
Posted By 11Black-GS

Help with header install, especially if you did on a GS or Z06

I cannot get the driver side header installed on my GS. I have 1 3/4 Kooks and this oil line is in the way. I have not read anywhere that this needed to be touched. I have my vehicle on 12 inch wheel...
Forum: C6 Corvette General Discussion
03-03-2016, 03:50 PM
Replies: 22
Views: 2,527
Posted By 11Black-GS

Yellow would look good too. I really like red but...

Yellow would look good too. I really like red but I see so many cars with red calipers that Im now thinking of getting yellow to be more different.
Forum: C6 Corvette General Discussion
02-29-2016, 07:15 PM
Replies: 11
Views: 831
Posted By 11Black-GS

That is just normal build up. Driving it hard...

That is just normal build up. Driving it hard won't hurt, but it will turn the pipes black a lot quicker.
Forum: C6 Corvette General Discussion
02-29-2016, 02:41 PM
Replies: 30
Views: 1,323
Posted By 11Black-GS

Mr Abbott, I do appreciate that you took the...

Mr Abbott,

I do appreciate that you took the time to reply.

If Zip's business model is to have a website that charges X amount shipping because of Y amount order total, then that is fine....
Forum: C6 Corvette General Discussion
02-29-2016, 01:53 PM
Replies: 30
Views: 1,323
Posted By 11Black-GS

To those who have MSDs....do you guys have...

To those who have MSDs....do you guys have headers?
Forum: C6 Corvette General Discussion
02-29-2016, 11:57 AM
Replies: 30
Views: 1,323
Posted By 11Black-GS

Anyone know of comparable plug wires to ones offered by Zip?

I just went to purchase these wires and noticed they want to charge me $21 for ground shipping and I am only one state away from them. :toetap:

To see a company out there who still likes to...
Forum: C6 Corvette General Discussion
02-27-2016, 08:39 PM
Replies: 1
Views: 1,063
Posted By 11Black-GS

Questions about this oil line and what its wrapped with

I am installing headers and noticed the heat reflection appeared to be soaked. I removed it and the line doesn't seem to be leaking, so I believe it may have been soaked from PB blaster overspray...
Forum: C6 Corvette General Discussion
01-26-2016, 05:50 PM
Replies: 16
Views: 1,955
Posted By 11Black-GS

I had the rear end on ramps. Took me about 3...

I had the rear end on ramps. Took me about 3 hours to do. The job is straight forward but takes patience when trying to connect everything neatly so the exhaust tips line up nicely.
Forum: C6 Corvette General Discussion
01-06-2016, 10:32 PM
Replies: 48
Views: 4,087
Posted By 11Black-GS

:lurk: Waiting for translation..

:lurk:

Waiting for translation..
Forum: C6 Corvette General Discussion
10-12-2015, 07:32 AM
Replies: 15
Views: 883
Posted By 11Black-GS

I second the fact that its probably a wheel speed...

I second the fact that its probably a wheel speed sensor. My dash board was lit up like a Christmas tree on my BMW when a speed sensor went. I had 3 of them replaced during the life of the car.
Forum: C6 Corvette General Discussion
10-09-2015, 02:15 PM
Replies: 17
Views: 2,383
Posted By 11Black-GS

Have you done a test of the temps prior to...

Have you done a test of the temps prior to installing this device? I'd be curious to know exactly how much it lowers the temperature.
Forum: C6 Corvette General Discussion
10-09-2015, 01:27 PM
Replies: 103
Views: 8,449
Posted By 11Black-GS

I used to have an M3 as a daily driver and drove...

I used to have an M3 as a daily driver and drove it in the winter. I had studded snow tires and I had no problems with traction. What about a Carrera 4s? All wheel drive would be ideal for you.
Forum: C6 Corvette General Discussion
10-09-2015, 12:12 PM
Replies: 74
Views: 26,888
Posted By 11Black-GS

96-02 Viper or 07-09 GT500. The Viper runs low...

96-02 Viper or 07-09 GT500. The Viper runs low 12s stock, the GT500 runs high 12s stock. Put on drag radials and you will get better times without adding horsepower.
Forum: C6 Corvette General Discussion
10-07-2015, 08:42 AM
Replies: 14
Views: 6,015
Posted By 11Black-GS

I bought mine from the company in MD. I didn't...

I bought mine from the company in MD. I didn't get mine coated so maybe mine will arrive a little sooner. So far the company has been nice to deal with, and they did give me a 2-3 week time frame...
Forum: C6 Corvette General Discussion
10-07-2015, 06:32 AM
Replies: 14
Views: 6,015
Posted By 11Black-GS

For those who ordered headers, how long did it take to arrive?

I placed an order for Kooks headers on 9/10 from a forum vendor and they have not shipped. Does Kooks make the headers to order? How long did it take you guys to get your order?
Forum: C6 Corvette General Discussion
09-30-2015, 08:46 PM
Replies: 6
Views: 596
Posted By 11Black-GS

Zaino. Only because it seems everything is...

Zaino. Only because it seems everything is covered with a protectant on the leather in our cars. I've used Lexol in the past.
Forum: C6 Corvette General Discussion
09-28-2015, 07:18 AM
Replies: 47
Views: 10,491
Posted By 11Black-GS

Is there a good chance some of the plasti dip...

Is there a good chance some of the plasti dip will come off around the edges when you get new tires installed?
Showing results 1 to 25 of 252
 
Page 1 of 11
1
2
3
Last »


 
Forum Jump

Trending Topics

All times are GMT -4. The time now is 02:30 AM.