CorvetteForum - Chevrolet Corvette Forum Discussion

Search: Posts Made By: ItBites01
Showing results 1 to 21 of 21
Search took 0.81 seconds.
Forum: C4 Tech/Performance
05-16-2012, 03:04 AM
Replies: 2
Views: 790
Posted By ItBites01

Thanks cruiser

I may look into the upper arms - thanks for the lead. I like the factory arms and would like an offset shaft instead, but maybe no one makes one.

I already modified the spacers. I'm at 2.5 deg...
Forum: C4 Tech/Performance
05-14-2012, 09:17 PM
Replies: 2
Views: 790
Posted By ItBites01

Offset cross shaft?

Does anyone make an offset upper a-arm cross shaft for the C4 that gains additional camber
Forum: C4 Parts for Sale/Wanted
03-06-2012, 02:05 PM
Replies: 26
Views: 4,215
Posted By ItBites01

All, I bought this rear end and had it...

All,

I bought this rear end and had it shipped to Arizona. It is as advertised and the OP/seller conducted this sale professionally, honestly, and with courtesy. He is truly a gentleman. I just...
Forum: C4 Parts for Sale/Wanted
02-15-2012, 12:44 AM
Replies: 4
Views: 482
Posted By ItBites01

dan0617, Thanks, I'll check into it. Sounds...

dan0617,

Thanks, I'll check into it. Sounds interesting.
Forum: C4 Tech/Performance
02-15-2012, 12:33 AM
Replies: 18
Views: 7,174
Posted By ItBites01

Thanks a bunch all! Great info.

Thanks a bunch all! Great info.
Forum: C4 Tech/Performance
02-14-2012, 01:45 AM
Replies: 18
Views: 7,174
Posted By ItBites01

Thanks to all y'all on the great info. Didn't...

Thanks to all y'all on the great info. Didn't realize the halfshafts use 1350 u-joints, Thanks vetteoz!

Does the D44 use 1350 u-joints on its input yoke? The D36 had 1310 as I recall. If the...
Forum: C4 Tech/Performance
02-12-2012, 03:23 PM
Replies: 18
Views: 7,174
Posted By ItBites01

WVZR-1, The trans is a TH400 and uses the...

WVZR-1,

The trans is a TH400 and uses the non-bolted slip yoke (no threads in the output shaft). The u-joints are 1310, as that matches the input on the D36. The driveshaft was built by Denny's...
Forum: C4 Parts for Sale/Wanted
02-12-2012, 12:36 PM
Replies: 26
Views: 4,215
Posted By ItBites01

Joseph, I guess I'm a bad buyer; didnt...

Joseph,

I guess I'm a bad buyer; didnt figure shipping... But really have no clue - don't do this a lot. LOL

I can help if you need, no worries. I can call around. LMK
Forum: C4 Parts for Sale/Wanted
02-12-2012, 12:30 PM
Replies: 26
Views: 4,215
Posted By ItBites01

Joseph, The pallet sounds fine to me. ...

Joseph,

The pallet sounds fine to me. They're pretty durable when fully assembled.
Forum: C4 Parts for Sale/Wanted
02-12-2012, 12:28 PM
Replies: 26
Views: 4,215
Posted By ItBites01

joseph, Thanks for the leg work, I've never...

joseph,

Thanks for the leg work, I've never shipped anything like that either. Let me know.
Forum: C4 Tech/Performance
02-12-2012, 12:17 PM
Replies: 18
Views: 7,174
Posted By ItBites01

gsdave, Thanks for the halfshaft response,...

gsdave,

Thanks for the halfshaft response, that helps me out. I trust my halfshafts that I have now and want to use them. Also, thanks for the evilbay tip. I didn't even think to look there...
Forum: C4 Tech/Performance
02-12-2012, 12:15 PM
Replies: 18
Views: 7,174
Posted By ItBites01

Just for chuckles, I thought I'd let y'all know...

Just for chuckles, I thought I'd let y'all know my driveshaft is only about 13" long. The engine/transmision is set really far back in my application. My weight balance is 48%front, 52% rear. ...
Forum: C4 Tech/Performance
02-12-2012, 12:06 PM
Replies: 18
Views: 7,174
Posted By ItBites01

Thanks WVZR-1

WVZR-1,

Thanks for the 24mm dimension! Is that also the driveshaft difference?

My forward attach is similar to the one shown, but has flat plate bolted to the housing. The plate is 3/8 steel...
Forum: C4 Parts for Sale/Wanted
02-12-2012, 03:23 AM
Replies: 49
Views: 3,961
Posted By ItBites01

Thanks for the response, but I need the D44 rear.

Thanks for the response, but I need the D44 rear.
Forum: C4 Tech/Performance
02-11-2012, 11:01 PM
Replies: 18
Views: 7,174
Posted By ItBites01

Blue, thanks for the response! I get that...

Blue, thanks for the response!

I get that the driveshafts in the C4 are different between the ZF/D44 and the Auto/D36, but is that due to the different transmission lengths or is the D44 itself...
Forum: C4 Tech/Performance
02-11-2012, 10:31 PM
Replies: 18
Views: 7,174
Posted By ItBites01

Dana36 to Dana 44 swap - dimensions needed

I exploded my Dana36 C4 rear end and need to upgrade to the Dana44.

I have heard the Dana 44 requires a shorter driveshaft, which I assume means the distance from the stub axle centerlines to the...
Forum: C4 Parts for Sale/Wanted
02-11-2012, 10:19 PM
Replies: 26
Views: 4,215
Posted By ItBites01

Joseph? sent a response PM. I'm still...

Joseph? sent a response PM. I'm still interested.
Forum: C4 Parts for Sale/Wanted
02-11-2012, 10:16 PM
Replies: 4
Views: 482
Posted By ItBites01

Thanks for the lead. Joseph and I are talking.

Thanks for the lead. Joseph and I are talking.
Forum: C4 Parts for Sale/Wanted
02-10-2012, 03:03 AM
Replies: 4
Views: 482
Posted By ItBites01

WTB Dana 44 with 3.07

Looking for good Dana44 with 3.07 gears.

I exploded my Dana 36...

I only need the pumpkin with gears and the batwing... Dont need halfshafts, knuckles, brakes, spring, swaybar, etc... But for...
Forum: C4 Parts for Sale/Wanted
02-10-2012, 02:57 AM
Replies: 26
Views: 4,215
Posted By ItBites01

I'm interested. Really just need the pumpkin and...

I'm interested. Really just need the pumpkin and batwing though... Would you split that out? If not, for the right price I could take the whole thing...

Would you ship to Phoenix? Any idea of...
Forum: C4 Parts for Sale/Wanted
02-10-2012, 02:50 AM
Replies: 49
Views: 3,961
Posted By ItBites01

Is the rear end a Dana 44 or Dana 36? What is...

Is the rear end a Dana 44 or Dana 36? What is the gear ratio?
Showing results 1 to 21 of 21


 
Forum Jump

Trending Topics

All times are GMT -4. The time now is 11:21 PM.