CorvetteForum - Chevrolet Corvette Forum Discussion

 
Page 1 of 20
1
2
3
11
Last »
Search: Posts Made By: zuendler
Showing results 1 to 25 of 499
Search took 1.28 seconds.
Forum: C6 Tech/Performance
01-01-2023, 02:58 AM
Replies: 0
Views: 300
Posted By zuendler

Fuel Supply for Edelbrock E-Force

Today I noticed a terrible smell in my garage.
It turned out, the Kennel Bell Boost-a-pump toasted itself, in the sitting car.
I figured out, that it was always on power, it was spliced into where...
Forum: C6 Tech/Performance
10-17-2022, 03:53 PM
Replies: 7
Views: 959
Posted By zuendler

And another update, this information will be very...

And another update, this information will be very valueable for the next guy searching for this. ;)
I got answer from Edelbrock:Part # Qty. Description

72-9009 ...
Forum: C6 Tech/Performance
10-17-2022, 09:07 AM
Replies: 7
Views: 959
Posted By zuendler

Little progress, im pretty sure this is the...

Little progress, im pretty sure this is the correct tensioner:
https://www.amazon.sg/ACDelco-Original-Equipment-12552360-Tensioner/dp/B0049Z4TD6

ACDelco GM Original Equipment 12552360
or
Dayco...
Forum: C6 Tech/Performance
10-15-2022, 01:03 PM
Replies: 7
Views: 959
Posted By zuendler

1000 thanks! :hurray: I have a completely...

1000 thanks! :hurray:

I have a completely different tensioner, found out, that this version is used in the car:...
Forum: C6 Tech/Performance
10-15-2022, 08:17 AM
Replies: 7
Views: 959
Posted By zuendler

The 1575 is for dry sump and 1590 for wet sump....

The 1575 is for dry sump and 1590 for wet sump. Air cleaner and tensioner must be the same, for the belt i guess it should be the same I think. So it would help a lot, thank you!
Forum: C6 Tech/Performance
10-14-2022, 05:52 PM
Replies: 7
Views: 959
Posted By zuendler

Spare Parts for Edelbrock E-Force 1575 needed

Hello,

I just bought that 2012 Grand Sport with a 1575 E-Force in it.
Now it needs some maintenance, I need:

- new air cleaner (its broken)
- new serpentine belt
- new pully on the tensioner...
Forum: C6 Tech/Performance
09-25-2022, 07:05 AM
Replies: 9
Views: 800
Posted By zuendler

Thx, but this wont help either. The clutch has...

Thx, but this wont help either.
The clutch has so much grip, that even the owner with 5 years experience was not able to softly clutch in, likely when you wait at a stoplight and go slowly around...
Forum: C6 Tech/Performance
09-24-2022, 09:54 PM
Replies: 9
Views: 800
Posted By zuendler

Clutch for supercharged LS3

Hi,
after 12 years C3 I want add a C6 for daily use to my garage.
I found a nice 2013 grad sport with an Edelbrock Supercharger on it, dynoed at 620HP.
But there was one big issue at the test...
Forum: C3 Tech/Performance
10-04-2021, 09:35 AM
Replies: 5
Views: 468
Posted By zuendler

I already have custom made steel braided hoses...

I already have custom made steel braided hoses diretcly to the wilwood caliper and need to remove one as sample for reproduction. Itīs nothing from the shelf. I didnīt like the wilwood solution where...
Forum: C3 Tech/Performance
10-04-2021, 07:54 AM
Replies: 5
Views: 468
Posted By zuendler

Brake hose thread rear

Hi,
my 69 is currently at the paint shop on the lift and I have to disconnect the rear brake hoses at the frame. So I will need a plug, but currently I cant measure the size.
Can someone of you...
Forum: C3 Tech/Performance
05-28-2021, 07:42 AM
Replies: 8
Views: 2,001
Posted By zuendler

For documentation: The inner bearing for the...

For documentation:
The inner bearing for the 1350 spindles consists of a Timken LM48548 inner race (sams as outside) and a Timken LM48511 outer cup. The outer cup is machined down in diameter to the...
Forum: C3 Tech/Performance
04-26-2020, 06:32 PM
Replies: 25
Views: 3,294
Posted By zuendler

Just in the middle between 2 plug connectors and...

Just in the middle between 2 plug connectors and the center connector.
I think I took 4 or 5mm diameter.
Forum: C3 Tech/Performance
04-26-2020, 10:38 AM
Replies: 10
Views: 619
Posted By zuendler

Well, this is not super high quality. They just...

Well, this is not super high quality.
They just let a hole away to produce it easier.

...
Forum: C3 Tech/Performance
04-25-2020, 07:07 PM
Replies: 10
Views: 619
Posted By zuendler

Now, this is worth showing: ...

Now, this is worth showing:


https://cimg5.ibsrv.net/gimg/www.corvetteforum.com-vbulletin/800x543/img_9648_58d89662a3e71345a9ede95febf60d7709f63cdf.jpg

The old pickup was just hammered into...
Forum: C3 Tech/Performance
04-25-2020, 04:05 PM
Replies: 25
Views: 3,294
Posted By zuendler

The male caps already have a venting port to...

The male caps already have a venting port to solve the moinsture issue.
But the old females donīt. I have drilled a hole into the cap with the same setup and old fashion cap.
Forum: C3 Tech/Performance
04-25-2020, 02:33 PM
Replies: 8
Views: 1,536
Posted By zuendler

ok, this ist the level with 6 liters in it. So...

ok, this ist the level with 6 liters in it. So 6qts should come out at the full marking.
Everything alright.

...
Forum: C3 Tech/Performance
04-25-2020, 02:00 PM
Replies: 8
Views: 1,536
Posted By zuendler

I want to carry as much oil as possible. This...

I want to carry as much oil as possible.
This pan is advertised with 6qts.
It will replace my Milodon pan, which is 1" deeper and hangs out under the car.
Had several ground contacts, car is...
Forum: C3 Tech/Performance
04-25-2020, 08:16 AM
Replies: 8
Views: 1,536
Posted By zuendler

Maximum oil level in the pan

Hi,
I want check if my dipstick shows propper oil level.
Where should the maximum level be at?...
Forum: C3 Tech/Performance
03-24-2020, 03:19 PM
Replies: 10
Views: 619
Posted By zuendler

Thank you, I found an advise from moroso on a web...

Thank you, I found an advise from moroso on a web site where they recommend to braze the pipe to prevent
it from coming off because of vibrations. Seems this is the way to go.
They also recomend to...
Forum: C3 Tech/Performance
03-24-2020, 12:38 PM
Replies: 10
Views: 619
Posted By zuendler

BigBlock Mk VI Oil Pickup

Hi,
currently I have a Milodon oil pan under my zz502. But itīs too deep, hängs 1" below all other stuff under the car, and more than one time it hat contact to the ground.
Now I have a new Moroso...
Forum: C3 Tech/Performance
02-03-2020, 04:03 PM
Replies: 29
Views: 28,255
Posted By zuendler

From fitment a can say: the copper type fits...

From fitment a can say:
the copper type fits ok, itīs a bit larger than the original one, but goes in.
the aluminium core is a bit to wide, but goes in with a bit force. Then itīs also a bit longer...
Forum: C3 Tech/Performance
02-03-2020, 11:47 AM
Replies: 29
Views: 28,255
Posted By zuendler

I dont know where the copper core is from, it has...

I dont know where the copper core is from, it has no sticker like the other one.
My main radiator is already aluminum from dewitt, engine has also aluminum heads.
The heater core would be last...
Forum: C3 Tech/Performance
02-03-2020, 09:45 AM
Replies: 29
Views: 28,255
Posted By zuendler

Alright, now I have both cores here and need your...

Alright, now I have both cores here and need your help.
Both are looking good, which one is better?
The aluminum one is made in China, and one side is out of shape, itīs a bit angled.
As long as...
Forum: C3 Tech/Performance
01-31-2020, 08:17 AM
Replies: 108
Views: 16,587
Posted By zuendler

Well known flares :D ...

Well known flares :D

https://cimg2.ibsrv.net/gimg/www.corvetteforum.com-vbulletin/1200x800/c3_frankreich2018_6_8f3a0efb487e4cfcae4dbe0fa1cad08f6f96a153.jpg
Forum: C3 Tech/Performance
01-28-2020, 04:46 AM
Replies: 22
Views: 4,169
Posted By zuendler

I have this TKO with 3.7 rear, but a zz502...

I have this TKO with 3.7 rear, but a zz502 feeding it. For me a perfect setup.
For you in Califonia I would recomend the 4.11 rear end.
1st will be a bit shorter than you know it from other cars,...
Showing results 1 to 25 of 499
 
Page 1 of 20
1
2
3
11
Last »


 
Forum Jump

Trending Topics

All times are GMT -4. The time now is 03:42 AM.