CorvetteForum - Chevrolet Corvette Forum Discussion

 
Page 1 of 3
1
2
3
Search: Posts Made By: 69vetteL46
Showing results 1 to 25 of 66
Search took 1.34 seconds.
Forum: C3 Parts for Sale/Wanted
03-03-2010, 12:37 PM
Replies: 6
Views: 519
Posted By 69vetteL46

ttt

ttt
Forum: C3 Parts for Sale/Wanted
02-19-2010, 11:40 AM
Replies: 6
Views: 519
Posted By 69vetteL46

Hi Steve, That is not what I am looking...

Hi Steve,

That is not what I am looking for, but thanks for offering. I am looking for a conversion piece for a non-side-pipe car so I don't have to modify the rear quarters. The panel I am...
Forum: C3 Parts for Sale/Wanted
02-18-2010, 09:33 PM
Replies: 6
Views: 519
Posted By 69vetteL46

It does not matter to me. Thanks

It does not matter to me.

Thanks
Forum: C3 Parts for Sale/Wanted
02-18-2010, 12:46 PM
Replies: 6
Views: 519
Posted By 69vetteL46

WTB 68/69 Side Exhaust conversion exhaust panel

I am looking for a side exhaust conversion panel for a 69. Slightly damaged and/or 68 panels with backup light holes would also be acceptable.

Thanks!
Forum: C3 Parts for Sale/Wanted
12-17-2007, 06:31 PM
Replies: 0
Views: 236
Posted By 69vetteL46

WTB: 69 350/300 Base motor

Looking for a 69 Corvette 350/300hp base motor in the New England area. Please PM if you have one for sale.

Thanks
Forum: C4 Tech/Performance
04-18-2007, 04:04 PM
Replies: 29
Views: 1,113
Posted By 69vetteL46

My car ran great cold.. It would only die once it...

My car ran great cold.. It would only die once it got warm... I battled this problem for a while. The best bet would be to put an auto-x-ray on the car to see all the vitals and such as well. A leak...
Forum: C4 Tech/Performance
04-18-2007, 03:43 PM
Replies: 29
Views: 1,113
Posted By 69vetteL46

Sounds like opti to me as well. I have been...

Sounds like opti to me as well. I have been through it on my 94. Its not a had job. Just expensive. I had the same problem and changed everyting (i.e. Fuel Filter, iginition module, all 2 O2 sensors,...
Forum: C3 Parts for Sale/Wanted
01-12-2007, 09:18 PM
Replies: 1
Views: 262
Posted By 69vetteL46

Looking for a 73 4-spd chassis.

Looking for a 73 4-spd chassis for a resto project.
Forum: C4 Tech/Performance
06-15-2006, 11:17 PM
Replies: 25
Views: 2,897
Posted By 69vetteL46

With what you changed it sounds like the opti to...

With what you changed it sounds like the opti to me as well as I changed everything you did as well except the cap. have a 94 and it was doing the same thing. (Not throwing any codes) Changed my...
Forum: C4 Tech/Performance
06-13-2006, 11:50 AM
Replies: 12
Views: 566
Posted By 69vetteL46

If the car has an EGR you may want to check that...

If the car has an EGR you may want to check that a well. If you are confident the solenoid is fine then check the egr with a vacuum pump with the motor off to see if the diaphram hold vacuum. If that...
Forum: C4 Tech/Performance
06-12-2006, 09:53 PM
Replies: 7
Views: 614
Posted By 69vetteL46

Thanks everyone for your input. It was the...

Thanks everyone for your input. It was the opti-spark. Got a delco water pump and opti from advance on last friday and replaced it on saturday. The car has never run so well. Thanks again!!
Forum: C4 Tech/Performance
06-07-2006, 06:47 PM
Replies: 1
Views: 358
Posted By 69vetteL46

Anyone want to look at a csv from Auto-Xray?

my 94 tends to miss and idle rough once warm. I did a capture with auto-xray and have some data. It seems the o2 sensors, recently replaced are showing lean then 07mv- 800 mv at an idle. However I'm...
Forum: C4 Tech/Performance
06-07-2006, 04:30 PM
Replies: 7
Views: 614
Posted By 69vetteL46

Ran an auto-xray capture on it today. Problem did...

Ran an auto-xray capture on it today. Problem did not seem as bad. O2 sensor readingins seemd very low. Would go from 62mv all the way to 800. I have a csv file with data. Would anyone like to look...
Forum: C4 Tech/Performance
06-03-2006, 11:25 PM
Replies: 7
Views: 614
Posted By 69vetteL46

94 Runs rough & lean when hot then stalls

I have a 94 with 56k on it that about 70% of the time seems to run lean, stumble, ping, misfire, and eventually stall if at an idle once the car gets to operating temp.

If car is cool or has...
Forum: C4 Tech/Performance
06-03-2006, 10:36 PM
Replies: 3
Views: 875
Posted By 69vetteL46

Using a crow's foot O2 removal tool you can rent...

Using a crow's foot O2 removal tool you can rent from autozone for $15 you should be able to remove the two O2 sensors before the cats. I was able to on my 94 convertible. However, the exhaust is...
Forum: C4 Parts for Sale/Wanted
05-26-2005, 07:30 PM
Replies: 3
Views: 210
Posted By 69vetteL46

I'm looking for the entire drivers side assembly

I'm looking for the entire drivers side assembly
Forum: C4 Parts for Sale/Wanted
05-26-2005, 07:12 PM
Replies: 3
Views: 210
Posted By 69vetteL46

WTB 1991-1996 Fog Lights

Looking for a drivers side foglight for a 1991-1996 coupe. If someone has one or even a full set please contact me at rquattrucci@cox.net.
Forum: C3 Tech/Performance
10-10-2004, 08:42 PM
Replies: 5
Views: 494
Posted By 69vetteL46

Thanks Guys... looks like I got some...

Thanks Guys... looks like I got some "un-modification" to do.

69 VetteL46
Forum: C3 Tech/Performance
10-10-2004, 07:23 PM
Replies: 5
Views: 494
Posted By 69vetteL46

69 Air Cleaner Issue w/PICS 56k Beware

I have a 69 L46 Coupe I am restoring. I have what I think to be the original air cleaner and throttle cable bracket. I am having an issues with the throttle cable bracket hitting the air cleaner. So...
Forum: C3 Tech/Performance
11-03-2003, 09:12 PM
Replies: 22
Views: 1,263
Posted By 69vetteL46

Re: Swap meet guys are on crack (gtr1999)

I take it you were at Thompson. The place was dead yesterday. I heard Saturday was much better. I usually dont have much luck finding corvette stuff at any of the local shows, Thompson, Stafford,...
Forum: C3 Tech/Performance
11-01-2003, 07:54 PM
Replies: 3
Views: 644
Posted By 69vetteL46

Crane Cams grind 294 H8

Does anyone know what the specs are for this grind, I can't seem to find it on their website. This is the cam I found in my L46. It's still like new and am curious as its specs and how it compares to...
Forum: C3 Parts for Sale/Wanted
09-12-2003, 12:31 PM
Replies: 7
Views: 430
Posted By 69vetteL46

Re: 1980 trailing arms (John Lynch)

Just want to inform everybody that Jared has made good on his promise to refund my money for the trailing arms. I recieved a paypal payment today. Jared, please be sure that John gets his trailing...
Forum: C3 Parts for Sale/Wanted
09-11-2003, 11:11 PM
Replies: 7
Views: 430
Posted By 69vetteL46

Re: 1980 trailing arms (John Lynch)

John,

I actually got in touch with Jared tonight on the phone (been trying off and on for a year) after I posted this message. He has promised me that I will have my money by 1pm eastern...
Forum: C3 Parts for Sale/Wanted
09-11-2003, 09:20 PM
Replies: 7
Views: 430
Posted By 69vetteL46

Re: 1980 trailing arms (slvr84)

Jared... Remember me... the guy you sold the trailing arms to last year and kept my 300 dollars??????? How dare you try to sell them again and not ever refund my money in over a year. You are a theif...
Forum: C3 Tech/Performance
09-09-2003, 09:16 PM
Replies: 9
Views: 2,351
Posted By 69vetteL46

Re: Does anyone have POR-15 application tips? (burners)

Forget all about the brushes and spray guns. When I painted my frame I used a small 4" roller to apply the POR-15. The brush is good for the small tight areas but takes way too long and cant get...
Showing results 1 to 25 of 66
 
Page 1 of 3
1
2
3


 
Forum Jump

Trending Topics

All times are GMT -4. The time now is 09:45 PM.