CorvetteForum - Chevrolet Corvette Forum Discussion

 
Page 1 of 20
1
2
3
11
Last »
Search: Posts Made By: spinadog
Showing results 1 to 25 of 498
Search took 1.46 seconds.
Forum: C3 Parts for Sale/Wanted
07-26-2021, 06:46 PM
Replies: 0
Views: 249
Posted By spinadog

FS: 1970 NOS horn button

Brand 'new' in box from GM, genuine NOS part (from Ecklers), unassembled, unpainted. This came as a spare with my now-sold C3 which was a 1970 tilt-tele model. Please check the pictures thoroughly as...
Forum: C3 Tech/Performance
07-04-2019, 10:24 AM
Replies: 14
Views: 2,790
Posted By spinadog

Thanks for the suggestions. I have already looked...

Thanks for the suggestions. I have already looked at both adjustments, and am pulling the box to send to Gary for a rebuild. Still looking for the best way to get it out, but I think from the top it...
Forum: C3 Tech/Performance
07-03-2019, 04:37 PM
Replies: 14
Views: 2,790
Posted By spinadog

Bumping this one, I am about to attempt it again...

Bumping this one, I am about to attempt it again (arrival of a small baby boy 2 days after post stopped all work on the 'vette). Anybody have this situation and can advise on the best way to remove?...
Forum: C3 Tech/Performance
07-03-2019, 04:31 PM
Replies: 14
Views: 2,790
Posted By spinadog

Bumping this one, I am about to attempt it again...

Bumping this one, I am about to attempt it again (arrival of a small baby boy 2 days after post stopped all work on the 'vette). Anybody have this situation and can advise on the best way to remove?...
Forum: C3 Parts for Sale/Wanted
01-18-2019, 09:02 AM
Replies: 19
Views: 2,391
Posted By spinadog

Well, as I mentioned, I have seen this exact carb...

Well, as I mentioned, I have seen this exact carb picture posted on eBay for the last 4+ years from this builder, so that would make me wary of authenticity. Missing the decellerator simply added to...
Forum: C3 Parts for Sale/Wanted
01-18-2019, 08:58 AM
Replies: 19
Views: 2,391
Posted By spinadog

I completely agree - my card is 100% correct,...

I completely agree - my card is 100% correct, except it comes up as a 'warranty replacement' if I look up the number. Build was Feb 19 1079.
Forum: C3 Parts for Sale/Wanted
01-17-2019, 01:09 PM
Replies: 19
Views: 2,391
Posted By spinadog

That carb has been advertised on eBay for the...

That carb has been advertised on eBay for the last few years....by the way. I'm looking for the same one myself! i seriously doubt it's authenticity, as it's missing the coveted 'decellerator'...
Forum: C3 Tech/Performance
01-17-2019, 12:13 PM
Replies: 28
Views: 2,102
Posted By spinadog

I had this problem and a hi-flow thermostat...

I had this problem and a hi-flow thermostat (moroso?) completely eradicated the issue. I also drilled the 1/8" hole to prevent air pockets - also a huge success. 468 with a Dewitt radiator (awesome)...
Forum: C3 Tech/Performance
01-17-2019, 12:05 PM
Replies: 14
Views: 2,790
Posted By spinadog

Piling on a little here, I have this issue - zero...

Piling on a little here, I have this issue - zero threads and my internals are shot, as I have 2-3" of play - I completely rebuilt the steering but should have done the steering box at the same time...
Forum: C3 Tech/Performance
01-14-2019, 12:45 PM
Replies: 15
Views: 1,670
Posted By spinadog

I did. I had the exact same issue with #6...

I did. I had the exact same issue with #6 cylinder on my 454, spurting oil everywhere at idle (700rpm), compared to the rest. This was preceded by a ticking noise while warming up, that suddenly...
Forum: C3 Tech/Performance
06-22-2017, 06:04 PM
Replies: 19
Views: 2,893
Posted By spinadog

OP & Lars, not derailing this thread, but I too...

OP & Lars, not derailing this thread, but I too would benefit greatly from knowing the right 'stack' of gaskets. Right now I have the following stack: manifold-thin gasket-heat shield-1/4"...
Forum: C3 Tech/Performance
06-22-2017, 05:57 PM
Replies: 6
Views: 2,947
Posted By spinadog

Sticky steering wheel? 303 Aerospace protectant

My car had been sitting for 9 months and my steering wheel, due to non-use had literally decomposed/melted, as the oils leached out the 47 year old plastics. Driving these cars fairly regularly...
Forum: C3 Tech/Performance
06-21-2017, 11:17 AM
Replies: 21
Views: 1,632
Posted By spinadog

Wow. This sounds very close to what I went...

Wow. This sounds very close to what I went through recently. I ended up replacing both lifters and my fuel pump, but start with the fuel pump. Mine was slightly galled on the end from the rod, or...
Forum: C3 Tech/Performance
06-19-2017, 03:29 PM
Replies: 2
Views: 745
Posted By spinadog

The reproduction passenger manifold that I...

The reproduction passenger manifold that I purchased ('70BB) was identical except for a reinforcing rod that was inside the manifold itself. The casting also appeared a little rougher around the...
Forum: C3 Tech/Performance
06-18-2017, 02:48 PM
Replies: 30
Views: 9,725
Posted By spinadog

Hi Kirk, it's odd you mention vacuum. I just...

Hi Kirk, it's odd you mention vacuum. I just checked yesterday and I am pulling a steady 19", compared to a fluttering 18" beforehand. I attribute that to a better sealed intake rather than any...
Forum: C3 Tech/Performance
06-17-2017, 05:01 PM
Replies: 30
Views: 9,725
Posted By spinadog

Resolution

I finally manned up to the start-2000-RPM-30-minute madness with the help of my lovely fiancee. I am happy to report that I have an intact cam, and replacement of either my lifters or fuel pump...
Forum: C3 Tech/Performance
05-05-2017, 08:50 AM
Replies: 24
Views: 3,533
Posted By spinadog

I Installed an MSD tach drive distributor and...

I Installed an MSD tach drive distributor and changed my advance vacuum 'can' to a unit that required more vacuum. Fixed all my detonation issues at throttle. I either HAD a B2 can or changed it to...
Forum: C3 Tech/Performance
05-05-2017, 08:44 AM
Replies: 54
Views: 6,407
Posted By spinadog

secondaries are there to be opened....not just...

secondaries are there to be opened....not just for show.
Forum: C3 General
05-03-2017, 12:49 PM
Replies: 19
Views: 4,250
Posted By spinadog

Hey Robbie, fellow ex-Melbourne enthusiast here. ...

Hey Robbie, fellow ex-Melbourne enthusiast here. Has the car been converted to RHD? Could affect geometries. As others have said, absolutely no need for hydraulic clutch, the mechanical one is...
Forum: C3 Tech/Performance
04-28-2017, 11:37 AM
Replies: 30
Views: 9,725
Posted By spinadog

:) - I could totally believe that, having...

:) - I could totally believe that, having performed plenty of aftersales analysis for these guys and most other brands....
Forum: C3 Tech/Performance
04-28-2017, 11:35 AM
Replies: 30
Views: 9,725
Posted By spinadog

The cam is in unbelievably good shape, only 3000...

The cam is in unbelievably good shape, only 3000 miles, as stated - the lobes look new. ZDDP oils and additive used 100% all the time. Oil changed each 1000 miles or annually. The lifters all...
Forum: C3 Tech/Performance
04-28-2017, 09:21 AM
Replies: 30
Views: 9,725
Posted By spinadog

Unfortunately, I do not. I gather that could...

Unfortunately, I do not. I gather that could help alleviate load during break in?

And yes, single coil with flat surge spring.
Forum: C3 Tech/Performance
04-27-2017, 12:37 PM
Replies: 20
Views: 6,269
Posted By spinadog

Can't speak for SB but the BB version with...

Can't speak for SB but the BB version with Magnaflows fitted my '70 perfectly - the exhaust installer guy said he was really impressed with fit and quality. I agree, and the sound is nice, not over...
Forum: C3 Tech/Performance
04-27-2017, 12:29 PM
Replies: 30
Views: 9,725
Posted By spinadog

Yep, some digging shows the same procedure as if...

Yep, some digging shows the same procedure as if a new cam. Moly cam lube is on the way, I'll pull them out and do it right. I'm sure she'll start first time, but I will overhaul carb, fuel line...
Forum: C3 Tech/Performance
04-26-2017, 01:13 PM
Replies: 30
Views: 9,725
Posted By spinadog

Thanks for the responses, and if you read from...

Thanks for the responses, and if you read from the top of the thread, I use open rocker covers to get perfect clearance. I'm very much in tune with this motor, having rebuilt it personally.

And,...
Showing results 1 to 25 of 498
 
Page 1 of 20
1
2
3
11
Last »


 
Forum Jump

Trending Topics

All times are GMT -4. The time now is 03:33 AM.