CorvetteForum - Chevrolet Corvette Forum Discussion

 
Page 1 of 2
1
2
Search: Posts Made By: Ehco1
Showing results 1 to 25 of 31
Search took 1.04 seconds.
Forum: C3 Tech/Performance
03-27-2009, 11:42 PM
Replies: 10
Views: 1,074
Posted By Ehco1

New T56

I finished my T56 install. It is a good fit and really changed the car's performance. I changed the rear end to 3;73S. I still need to get the speedo hooked up. Is everyone using the cable x or...
Forum: C3 Tech/Performance
03-27-2009, 11:31 PM
Replies: 1
Views: 303
Posted By Ehco1

Electrical HELP

OK, I was trying to fish my speaker wire up to connect my new speakers. All of a sudden the smoke ecsaped from the wire. I know as long as the smoke stays inside, I am good to go. Any way the radio...
Forum: C3 General
03-12-2009, 12:02 PM
Replies: 6
Views: 808
Posted By Ehco1

I replaced mine this winter. I had to grind them...

I replaced mine this winter. I had to grind them down a little bit. I then used the grease that came with them and still had to use two pieces of plate steel with holes drilled in them and bolt and...
Forum: C3 Tech/Performance
02-18-2009, 12:06 PM
Replies: 9
Views: 716
Posted By Ehco1

I used warlock mufflers. It went in the stock...

I used warlock mufflers. It went in the stock location and the cut outs are built in the muffler.
Forum: C3 General
02-06-2009, 03:37 PM
Replies: 111
Views: 2,255
Posted By Ehco1

Since 1996, My oldest daughter gets it when I am...

Since 1996, My oldest daughter gets it when I am done with it.
Forum: C3 Tech/Performance
02-06-2009, 03:16 PM
Replies: 3
Views: 1,034
Posted By Ehco1

When I did mine I was told for a Tranny mount use...

When I did mine I was told for a Tranny mount use rubber it absorbs vibration where poly won't. I used rubber. I don't know for a fact it is true but it makes sence to me.
Forum: C3 Tech/Performance
01-31-2009, 11:21 PM
Replies: 4
Views: 397
Posted By Ehco1

I am going to use a cable X. My T-56 is in I am...

I am going to use a cable X. My T-56 is in I am waiting to get my rear differential back. Do a search on the internet for the Cable X.
Forum: C3 Tech/Performance
01-29-2009, 11:32 AM
Replies: 12
Views: 313
Posted By Ehco1

I am not sure who the manufacturer is. I picked...

I am not sure who the manufacturer is. I picked it up on ebay out of an 1982. They were installed for a few hours and removed, or so the story goes. My car is a 1980. I have everything else, new...
Forum: C3 Tech/Performance
01-29-2009, 09:04 AM
Replies: 12
Views: 313
Posted By Ehco1

Ring Gear Question

Long story made short. I took my rear differential to a local mechanic to change the original gear set to 373s. I have needed extra part after extra part. Most of I guess was a good idea, why not...
Forum: C3 Tech/Performance
01-07-2009, 04:33 PM
Replies: 5
Views: 249
Posted By Ehco1

Thanks:cheers:

Thanks:cheers:
Forum: C3 Tech/Performance
01-07-2009, 04:04 PM
Replies: 5
Views: 249
Posted By Ehco1

The car Is TPI with it's computer and has a T56.

The car Is TPI with it's computer and has a T56.
Forum: C3 Tech/Performance
01-07-2009, 11:42 AM
Replies: 5
Views: 249
Posted By Ehco1

Another Guage Swap Question

Has anyone put C5 guages in a C3? What would be involved?

Thanks
Forum: C3 Tech/Performance
12-17-2008, 03:52 PM
Replies: 24
Views: 17,629
Posted By Ehco1

I will look at it. Thanks

I will look at it.

Thanks
Forum: C3 Tech/Performance
12-17-2008, 02:27 PM
Replies: 24
Views: 17,629
Posted By Ehco1

I am looking at the same thing TPI on my 80. I...

I am looking at the same thing TPI on my 80. I found a computer from Megasquirt, It looks like you can by-pass some of the sensors. It is cheaper than GM computers, and they say it is very...
Forum: C3 Tech/Performance
12-17-2008, 01:53 PM
Replies: 19
Views: 5,408
Posted By Ehco1

Has anyone tried the Megasquirt computer? It is...

Has anyone tried the Megasquirt computer? It is supposed to be more efficient, and cheaper to buy. I am looking at using with a TPI setup.:lurk:
Forum: C3 Tech/Performance
12-02-2008, 04:08 PM
Replies: 6
Views: 428
Posted By Ehco1

I ordered a t-56 knob on e-bay for about 24.00. ...

I ordered a t-56 knob on e-bay for about 24.00. I modified the t-56 shifterto fit my console.
Forum: C3 Tech/Performance
11-10-2008, 10:30 AM
Replies: 5
Views: 695
Posted By Ehco1

Thanks I will try and get the tool and use the...

Thanks I will try and get the tool and use the clamp.
Forum: C3 Tech/Performance
11-09-2008, 12:27 PM
Replies: 5
Views: 695
Posted By Ehco1

80 Strut rod Removal.

I am trying to remove my strut rods and can not get the lowers to come loose. Everything is out including the rear differentail. Are they pressed in? I can not get them to move with my dead blow...
Forum: C3 Tech/Performance
10-20-2008, 12:38 PM
Replies: 6
Views: 685
Posted By Ehco1

Thanks, Good to know before I try. I will do it...

Thanks, Good to know before I try. I will do it the right way.
Forum: C3 Tech/Performance
10-20-2008, 12:26 PM
Replies: 6
Views: 685
Posted By Ehco1

I will be replacing the transmission. I thought...

I will be replacing the transmission. I thought with all that out of the way I might save some time if I could pull it from the front and not have unhook the suspenion and not have to realign...
Forum: C3 Tech/Performance
10-20-2008, 12:01 PM
Replies: 6
Views: 685
Posted By Ehco1

Rear Differential Removal

Does anyone know if I can pull the rear differential from the front while I have my transmission out?
Forum: C3 Tech/Performance
10-17-2008, 07:04 PM
Replies: 3
Views: 1,519
Posted By Ehco1

I already have the LS-1 T-56. I got it for a...

I already have the LS-1 T-56. I got it for a song about $500.00 so I need to use it.
Forum: C3 Tech/Performance
10-17-2008, 12:53 PM
Replies: 3
Views: 1,519
Posted By Ehco1

Another T56 swap question

There is a lot of conflicting information about swapping a LS-1, T-56 to a C-3. I found this and was courious if this is accurate.

If you’re starting from scratch and already have a 3 or 4 speed...
Forum: C3 Tech/Performance
09-26-2008, 11:17 AM
Replies: 16
Views: 2,120
Posted By Ehco1

I am collecting parts and getting ready to...

I am collecting parts and getting ready to install the T-56 in my 80. Keven at The Gear Box has been very helpful. His parts are more affortable than some of the other vendors.
Forum: C3 Tech/Performance
09-18-2008, 10:37 AM
Replies: 42
Views: 39,367
Posted By Ehco1

I have been getting ready to do the swap and have...

I have been getting ready to do the swap and have been trying to research what I will need. I found this and it explains alot. Alot of the vendors have helped also. Check out this article. I hope...
Showing results 1 to 25 of 31
 
Page 1 of 2
1
2


 
Forum Jump

Trending Topics

All times are GMT -4. The time now is 03:20 AM.