CorvetteForum - Chevrolet Corvette Forum Discussion

 
Page 1 of 3
1
2
3
Search: Posts Made By: mrgrimes
Showing results 1 to 25 of 74
Search took 1.15 seconds.
Forum: Autocrossing & Roadracing
03-17-2008, 12:19 AM
Replies: 20
Views: 2,462
Posted By mrgrimes

I bought the same bender but have not used it...

I bought the same bender but have not used it yet. I was planning on .120 tubing which hopefully not deflect as much as your .095"

Are you going to or have you tried the bender with .120...
Forum: C4 Tech/Performance
05-20-2007, 11:34 PM
Replies: 11
Views: 2,142
Posted By mrgrimes

Looks good. Did you buy this as a weld in...

Looks good.

Did you buy this as a weld in kit or did you make this from scratch?
Forum: Autocrossing & Roadracing
05-01-2007, 05:59 PM
Replies: 12
Views: 11,869
Posted By mrgrimes

The reason I asked was it's hard to get any...

The reason I asked was it's hard to get any specifics out of the roll cage vendors about fit and finish, let alone a picture.

I really want the build it myself, mostly because I enjoy doing that...
Forum: Autocrossing & Roadracing
04-30-2007, 01:39 PM
Replies: 12
Views: 11,869
Posted By mrgrimes

Thanks for the info but I live in Seattle. I am...

Thanks for the info but I live in Seattle. I am suprised by how little interest there is in this forum for C4 roll cages.
Forum: Autocrossing & Roadracing
04-28-2007, 01:08 AM
Replies: 12
Views: 11,869
Posted By mrgrimes

Which C4 weld on 8 point Roll Cage is better?

S&W, Autopower, or Kirk?

Which one has better fit?

Darrin
Forum: C4s for Sale/Wanted
04-26-2007, 03:30 PM
Replies: 8
Views: 1,655
Posted By mrgrimes

Hello, How do you like the Kirk roll bar? How...

Hello,
How do you like the Kirk roll bar? How come the full roll cage was not installed? Does not full roll cage have good fit? Could you describe where the roll bar/cage contacts the chassis?
...
Forum: C4 Tech/Performance
04-04-2007, 10:27 PM
Replies: 7
Views: 863
Posted By mrgrimes

No fun in Seattle

Thanks, but I guess there's not many car nuts in Seattle!
Forum: C4 Tech/Performance
04-03-2007, 12:09 AM
Replies: 7
Views: 863
Posted By mrgrimes

Engine Rebuild shop in Seattle area?

Does any one know of a quality engine rebuild shop in the Seattle area that can perform high precision cyl head surfacing (acceptable surface smoothness), valve/valve seat grind, block honing?
...
Forum: C4 Tech/Performance
11-01-2006, 12:36 AM
Replies: 6
Views: 3,134
Posted By mrgrimes

thanks, I never thought it would weigh so much!

thanks, I never thought it would weigh so much!
Forum: C4 Tech/Performance
10-27-2006, 06:56 PM
Replies: 6
Views: 3,134
Posted By mrgrimes

How much do they weigh when shipped?

How much do they weigh when shipped?
Forum: C4 Tech/Performance
10-26-2006, 05:35 PM
Replies: 6
Views: 1,129
Posted By mrgrimes

The runners had a 30% increase in flow over stock...

The runners had a 30% increase in flow over stock and the throttle body was 1000CMF. I only drove the cars to develop the software for the controller and I remember 1000 rpm increase from back then,...
Forum: C4 Tech/Performance
10-26-2006, 03:08 PM
Replies: 6
Views: 1,129
Posted By mrgrimes

Yeah, I used to work for Airsensors, the company...

Yeah, I used to work for Airsensors, the company that originally made the castings and electronics back in the late 1980s. It will make your car go fast with an extra 1000 rpm to boot on a stock L98.
Forum: C4 Tech/Performance
10-26-2006, 03:01 PM
Replies: 6
Views: 3,134
Posted By mrgrimes

weight of a L98 or LT1 with accessories?

Does any one know? Thanks.
Forum: C4 Parts for Sale/Wanted
06-26-2006, 01:21 AM
Replies: 4
Views: 453
Posted By mrgrimes

Sorry, I didn't read it correctly.

Sorry, I didn't read it correctly.
Forum: C4 Parts for Sale/Wanted
06-26-2006, 01:20 AM
Replies: 4
Views: 453
Posted By mrgrimes

How much do you want for the drive shaft? Is...

How much do you want for the drive shaft? Is still balanced?
Forum: C1 & C2 Corvettes
06-26-2006, 01:15 AM
Replies: 21
Views: 1,447
Posted By mrgrimes

If you buy TKO don't expect to shift above 6500...

If you buy TKO don't expect to shift above 6500 rpm. They will not tell you this until after you buy the tranny.
Forum: C4 Tech/Performance
06-12-2006, 09:02 AM
Replies: 1
Views: 336
Posted By mrgrimes

unbalanced driveshaft - howto

I have a driveshaft, for a manual transmission car, without any balance weights. Are there any companies offering balancing for these things?
Darrin
Forum: C4 Tech/Performance
05-26-2006, 10:49 AM
Replies: 9
Views: 2,713
Posted By mrgrimes

auto vs manual driveshaft

Are the driveshafts for manual and automatic transmissions the same? Can I use the yokes off of a manual driveshaft on an driveshaft out of an auto tranny C4? I have an 1988 C4
Thanks!
Forum: C4 Tech/Performance
05-09-2006, 11:00 AM
Replies: 16
Views: 638
Posted By mrgrimes

How many after market high performance...

How many after market high performance transmissions are shift limited to less than 6500 rpm? When I called your (Kiesler) costomer service depart ment the guy laughed at me and said I would have to...
Forum: C4 Tech/Performance
05-09-2006, 10:54 AM
Replies: 16
Views: 638
Posted By mrgrimes

I did call Tremec and talked to them, after I...

I did call Tremec and talked to them, after I received the tranny. They told me I would have to have the syncros power shifted If I wanted to go above 6500 rpm, so are you willing to pay for this? ...
Forum: C4 Tech/Performance
05-09-2006, 10:36 AM
Replies: 16
Views: 638
Posted By mrgrimes

Yes, I mean bracket bolts to tranny, not C-beam. ...

Yes, I mean bracket bolts to tranny, not C-beam. The instructions describe them but they were not included in the box. I took a day off of work to do this part of the install, so it was a day of...
Forum: C4 Tech/Performance
05-09-2006, 01:32 AM
Replies: 16
Views: 638
Posted By mrgrimes

Do you mean Keisler?

Do you mean Keisler?
Forum: C4 Tech/Performance
05-09-2006, 12:29 AM
Replies: 16
Views: 638
Posted By mrgrimes

They said the syncros would not allow it.

They said the syncros would not allow it.
Forum: C4 Tech/Performance
05-08-2006, 11:11 PM
Replies: 16
Views: 638
Posted By mrgrimes

Aftermarket transmission warning!!!

What would you say to a company ( begins with a K) that sells an aftermarket transmission for your C4 vette and does not inform you that you cannot shift the thing above 6500 rpm or does not supply...
Forum: Autocrossing & Roadracing
05-08-2006, 10:29 PM
Replies: 20
Views: 1,232
Posted By mrgrimes

Here is a riddle - The cool thing about sonic...

Here is a riddle - The cool thing about sonic flow is it can turn a non-linear flow orifice into a linear one, WTF am I talking about?
Showing results 1 to 25 of 74
 
Page 1 of 3
1
2
3


 
Forum Jump

Trending Topics

All times are GMT -4. The time now is 01:39 AM.