CorvetteForum - Chevrolet Corvette Forum Discussion

 
Page 1 of 7
1
2
3
Last »
Search: Posts Made By: 56and67
Showing results 1 to 25 of 172
Search took 1.56 seconds.
Forum: C1 & C2 Parts
07-26-2014, 06:59 PM
Replies: 7
Views: 807
Posted By 56and67

Have a decent 3831731 tailhousing if anyone's...

Have a decent 3831731 tailhousing if anyone's interested.
Forum: C1 & C2 Parts
04-15-2014, 02:38 PM
Replies: 3
Views: 1,937
Posted By 56and67

It probably has been rebuilt since it has the...

It probably has been rebuilt since it has the dual fan bolt pattern flange. 1967 used the small pattern.
Forum: C1 & C2 Corvettes
04-10-2014, 09:11 AM
Replies: 3
Views: 2,037
Posted By 56and67

Added a couple more pixs. The one I have seems to...

Added a couple more pixs. The one I have seems to have been made in the same construction method as the 3770245 2-deep groove Corvette pulley.
Forum: C1 & C2 Corvettes
04-10-2014, 01:14 AM
Replies: 3
Views: 2,037
Posted By 56and67

1958 up Deep Water Pump Pulley 3724816

Have a correct stamped pulley and noticed that this original one is manufactured different than the repros. This one has the front edge of the groove attached to the face and the repros have a one...
Forum: C1 & C2 Parts
02-14-2014, 02:10 AM
Replies: 2
Views: 530
Posted By 56and67

Have an original decent set of I believe 13. Of...

Have an original decent set of I believe 13. Of course have some pitting but still shiny and match good. Not damaged. $150 plus shipping. Can dig them out of storage, inventory and send some pictures...
Forum: C1 & C2 Parts
11-08-2013, 03:26 PM
Replies: 3
Views: 366
Posted By 56and67

Not correct for a Chevy. Should have male brass...

Not correct for a Chevy. Should have male brass threads. Number at bottom of "2" is not correct. 1957-8 Chevy is "5". 1959-65 Chevy is a "4". Carter made different choke covers for many...
Forum: C1 & C2 Parts
10-17-2013, 02:53 PM
Replies: 1
Views: 341
Posted By 56and67

Have a nice one $35 plus shipping

Have a nice one $35 plus shipping
Forum: C1 & C2 Parts
10-08-2013, 10:24 PM
Replies: 4
Views: 760
Posted By 56and67

Have a couple of posi cases but may be too early,...

Have a couple of posi cases but may be too early, G87 and J17. Located in eastern WA. Rich
Forum: C1 & C2 Parts
06-17-2012, 05:20 PM
Replies: 2
Views: 424
Posted By 56and67

May have something, but am a little confused on...

May have something, but am a little confused on your description. By small base do you mean a small bolt pattern used on the early caddys and buicks. Or do you mean the thin base that was used on 2X4...
Forum: C1 & C2 Parts
04-23-2012, 10:45 PM
Replies: 5
Views: 440
Posted By 56and67

Without part numbers (for cast parts) or details...

Without part numbers (for cast parts) or details on what you need it makes it hard to help. I have some brackets that different from my 67 with AC.
Forum: C1 & C2 Parts
03-07-2012, 12:04 AM
Replies: 22
Views: 3,219
Posted By 56and67

Do you need a wide or close ratio?

Do you need a wide or close ratio?
Forum: C1 & C2 Parts
02-05-2012, 01:51 AM
Replies: 2
Views: 530
Posted By 56and67

Hey Ed, I have a perfect used original 3889372 BF...

Hey Ed, I have a perfect used original 3889372 BF That I will not be using. We probably both know what the dealers are asking for these. PM me for pictures or make a reasonable offer and it will be...
Forum: C1 & C2 Parts
02-03-2012, 08:43 PM
Replies: 0
Views: 1,496
Posted By 56and67

FS C1 Posi Cases 3743833 & 3789812

Cleaning up the garage and these Chevy posi-traction rear axle cases are excess. All are bare (except with cap/bolts), nice condition without problems.

3743833, Date G 8 7 , late 1957 or very...
Forum: C1 & C2 Parts
01-30-2012, 10:37 PM
Replies: 6
Views: 6,736
Posted By 56and67

Heads look like the real deal. Valve cover are...

Heads look like the real deal. Valve cover are later 7 fin type and should be 9 fin type. 57 Chev vehicle blocks used a dated code system not a motor serial number. Probably was a 1957 produced...
Forum: C1 & C2 Parts
01-30-2012, 09:49 PM
Replies: 4
Views: 575
Posted By 56and67

Need just a case or what ratio gears?

Need just a case or what ratio gears?
Forum: C1 & C2 Parts
01-20-2012, 09:26 PM
Replies: 6
Views: 6,736
Posted By 56and67

The stamping don't look like they were made by ...

The stamping don't look like they were made by factory dies to me. Especially the F and G.
Forum: C1 & C2 Parts
11-19-2011, 04:28 PM
Replies: 21
Views: 1,880
Posted By 56and67

Have a nice core. All required parts move freely....

Have a nice core. All required parts move freely. Not any damage and little corrosion. Has all original correct parts including original choke cover. A good cleanup and kit and ready to go. $175 plus...
Forum: C1 & C2 Parts
11-03-2011, 12:54 PM
Replies: 7
Views: 893
Posted By 56and67

Is this a deep or standard groove?

Is this a deep or standard groove?
Forum: C1 & C2 Parts
10-20-2011, 08:42 PM
Replies: 2
Views: 485
Posted By 56and67

Have a couple of 4657 cores. Rich in WA state

Have a couple of 4657 cores. Rich in WA state
Forum: C1 & C2 Parts
09-11-2011, 01:29 PM
Replies: 2
Views: 393
Posted By 56and67

The jetting on the single 4bbls was different...

The jetting on the single 4bbls was different than the dual fours because the motors were different. The motor and the carbs need to be matched (mainly to compression ratio and camshaft). I have many...
Forum: C1 & C2 Parts
08-23-2011, 03:42 AM
Replies: 5
Views: 4,875
Posted By 56and67

Pontiac and Cadillac for GM and Ford came out...

Pontiac and Cadillac for GM and Ford came out with the first Carter AFBs in 1957.
Forum: C1 & C2 Parts
07-22-2011, 06:24 PM
Replies: 1
Views: 344
Posted By 56and67

Have a close D187 in running condition. $135...

Have a close D187 in running condition. $135 shipped to lower US. Rich in WA state
Forum: C1 & C2 Parts
07-22-2011, 06:12 PM
Replies: 2
Views: 1,386
Posted By 56and67

Have a nice one, $45 including shipping. Rich in...

Have a nice one, $45 including shipping. Rich in WA state.
Forum: C1 & C2 Parts
03-15-2011, 12:50 AM
Replies: 3
Views: 539
Posted By 56and67

If original, should have a 3-bolt mount on it,...

If original, should have a 3-bolt mount on it, not the later 2-bolt, in my experience.
Forum: C1 & C2 Parts
02-28-2011, 05:26 AM
Replies: 5
Views: 556
Posted By 56and67

It's an over the counter replacement service carb...

It's an over the counter replacement service carb but a very early one. The holes were drilled for an aftermarket mod to provide tubes through to the secondary barrels for additional accelerator pump...
Showing results 1 to 25 of 172
 
Page 1 of 7
1
2
3
Last »


 
Forum Jump

Trending Topics

All times are GMT -4. The time now is 06:08 PM.