CorvetteForum - Chevrolet Corvette Forum Discussion

 
Page 1 of 20
1
2
3
11
Last »
Search: Posts Made By: marky mark
Showing results 1 to 25 of 476
Search took 1.56 seconds.
Forum: C3 Tech/Performance
11-07-2022, 11:34 AM
Replies: 7
Views: 432
Posted By marky mark

@Lt.Mike, Thanks for those videos. My lower...

@Lt.Mike,
Thanks for those videos.
My lower track sliders are both somewhat wobbly. Not sure how taut they would have been when new.
I’m guessing some movement is ok and too much is not.
Can’t...
Forum: C3 Tech/Performance
11-03-2022, 12:29 PM
Replies: 7
Views: 432
Posted By marky mark

68 -Early '69 Door Glass Mechanism Need Help

My early '69 convertible has one door with '68 glass & mechanism and the other with the '69 parts.
I am trying to install the windows (manual) and my best efforts for searching this subject has left...
Forum: C3 Tech/Performance
11-02-2022, 04:14 PM
Replies: 2
Views: 268
Posted By marky mark

@69L88, Thank you for the quick reply. ...

@69L88,

Thank you for the quick reply.
Yes that is correct now that i think about that area.
I should have remembered them as that is a tough part to change out, lol.
Thanks so much!
Forum: C3 Tech/Performance
11-02-2022, 03:59 PM
Replies: 2
Views: 268
Posted By marky mark

Please Help to Identify This Part

I found four of these in a box of old parts and I can't figure out what they are or where they went on the car.
Any helps greatly appreciated.
Car is a 1969 convertible.
Thanks!
Mark


...
Forum: C3 Tech/Performance
04-19-2021, 07:13 PM
Replies: 5
Views: 1,447
Posted By marky mark

Perfect! Nice photos. Thanks very much!

Perfect! Nice photos.
Thanks very much!
Forum: C3 Tech/Performance
04-19-2021, 05:49 PM
Replies: 5
Views: 1,447
Posted By marky mark

CAMS69, Thanks for the reply & info. Couple of...

CAMS69,
Thanks for the reply & info. Couple of other questions for you if possible:
For the 'inside' stainless trim piece that goes directly onto the windshield frame, is that where some have added...
Forum: C3 Tech/Performance
04-18-2021, 12:23 PM
Replies: 5
Views: 1,447
Posted By marky mark

C3 a pillar weatherstrip install question

After searching various threads on the A pillar windshield trim I am still unsure of one thing.
My question is: When installing the A pillar trim (stainless) retainer trim that holds the...
Forum: C3 General
01-30-2021, 07:37 PM
Replies: 32
Views: 11,007
Posted By marky mark

Found this old thread which describes the...

Found this old thread which describes the difficulty I am having with the lower dash install.
I have a new wire loom which is very stiff. New lower and upper dash pads as well.
Was thinking about...
Forum: C3 Tech/Performance
01-29-2021, 06:52 AM
Replies: 4
Views: 613
Posted By marky mark

Thanks GunPowder, I never knew the car...

Thanks GunPowder,

I never knew the car offered air from above the center gauge cluster.

one other question if you know:
did you route the vacuum lines to the console from behind the lower vent...
Forum: C3 Tech/Performance
01-28-2021, 05:48 PM
Replies: 31
Views: 6,827
Posted By marky mark

leigh322, The engraved main caps have an...

leigh322,
The engraved main caps have an interesting story.
When GM outsourced the build to Schwartz Machine they did not have that detail as part of the job.
Schwartz did that on their own. GM...
Forum: C3 Tech/Performance
01-28-2021, 05:37 PM
Replies: 4
Views: 613
Posted By marky mark

1969 non a/c heater vent install question

I am re-assembling my dash (finally) and have a question about the heater vents. This is a non a/c car.
The slender piece is what I'm asking about. Curious if I have it located in the right spot and...
Forum: C3 Tech/Performance
01-26-2021, 10:13 PM
Replies: 126
Views: 13,916
Posted By marky mark

That's the spirit. I too enjoy a challenge and...

That's the spirit.
I too enjoy a challenge and to try doing some car work that I have never done before.
But for me, taking out the steering column is a huge victory. My dash install is one thing...
Forum: C3 Tech/Performance
01-26-2021, 08:19 PM
Replies: 126
Views: 13,916
Posted By marky mark

If anyone reading this is thinking about getting...

If anyone reading this is thinking about getting a differential rebuild I can personally attest that Gary (GTR1999) is as good as it gets.
Not everyone is as brave as those doing their own rebuild...
Forum: C3 Tech/Performance
01-26-2021, 09:26 AM
Replies: 4
Views: 392
Posted By marky mark

Flyboy1958, Thank you for correcting me and my...

Flyboy1958,
Thank you for correcting me and my incorrect opinion of the bracket being an 'interference fit'.
The AIM picture you have is clear on the spot welds and I see what you mean about them...
Forum: C3 Tech/Performance
01-25-2021, 08:19 PM
Replies: 4
Views: 392
Posted By marky mark

A few other pictures. ...

A few other pictures.


https://cimg2.ibsrv.net/gimg/www.corvetteforum.com-vbulletin/1500x2000/img_0964_7897231d94e2bacfe78a4a62e8b3e5f82aab84cf.jpg...
Forum: C3 Tech/Performance
01-25-2021, 07:56 PM
Replies: 4
Views: 392
Posted By marky mark

1969 Convertible (no a/c) lower dash support rods and vent pictures

NOTE: Please read the reply in this thread by Flyboy1958. He has offered up the correct information about the bracket and how it is attached. My theory below, although well meaning, is incorrect. The...
Forum: C3 Tech/Performance
01-24-2021, 11:42 PM
Replies: 31
Views: 6,827
Posted By marky mark

are you meaning you have the aluminum small block...

are you meaning you have the aluminum small block or the ZL1 big block?
Forum: C3 Tech/Performance
01-23-2021, 07:37 PM
Replies: 29
Views: 2,361
Posted By marky mark

Thanks for the tips, appreciate the help.

Thanks for the tips, appreciate the help.
Forum: C3 Tech/Performance
01-23-2021, 05:05 PM
Replies: 31
Views: 6,827
Posted By marky mark

Will do. I have had bad luck with the flat...

Will do.
I have had bad luck with the flat tappets in previous engines thus the roller decision.
The billet is the way to go. Much better.
I do recommend Crower as I feel they are a cut above the...
Forum: C3 Tech/Performance
01-23-2021, 04:54 PM
Replies: 29
Views: 2,361
Posted By marky mark

CanadaGrant, That's a very helpful picture and...

CanadaGrant,
That's a very helpful picture and explanation. Thank you.

After experimenting with the seam sealer I have my doubts that it will really offer that much help in keeping the birdcage...
Forum: C3 Tech/Performance
01-20-2021, 02:53 PM
Replies: 29
Views: 2,361
Posted By marky mark

Ok I think I have a game plan. I will use body...

Ok I think I have a game plan.
I will use body caulk on the top of windshield frame prior to installing the trim pieces. This item is about as close to the old 'dum-dum' putty type material used by...
Forum: C3 Tech/Performance
01-19-2021, 05:57 PM
Replies: 29
Views: 2,361
Posted By marky mark

It appears that 3M caulk strips (as a substitute...

It appears that 3M caulk strips (as a substitute for the factory 'dum-dum' caulk?) are the go to product under the windshield ss header and corner trim.

My one question about where and how to...
Forum: C3 Tech/Performance
01-19-2021, 05:41 PM
Replies: 29
Views: 2,361
Posted By marky mark

caskiguy, I am posting your link for folks to...

caskiguy,
I am posting your link for folks to review. That was a lot of work!
I have, in the past, been an NCRS member but I did not really take advantage of their knowledge too much.
Maybe I will...
Forum: C3 Tech/Performance
01-19-2021, 05:01 PM
Replies: 29
Views: 2,361
Posted By marky mark

Joystick, See if this opens for you. This is...

Joystick,
See if this opens for you. This is the pdf that was mentioned.
This one is a great source if doing your own windshield install.
The only thing is it doesn't really offer up much detail...
Forum: C3 Tech/Performance
01-19-2021, 04:52 PM
Replies: 29
Views: 2,361
Posted By marky mark

Joystick, Here is a link to most of Alan's...

Joystick,
Here is a link to most of Alan's pictures in another thread.
I'll try and find the pdf.
Thanks
...
Showing results 1 to 25 of 476
 
Page 1 of 20
1
2
3
11
Last »


 
Forum Jump

Trending Topics

All times are GMT -4. The time now is 09:15 PM.