$999 shipped for Weapon7 splitter and rocker blades!!!!!!
06-20-2014, 11:22 PM
#1
Safety Car
Thread Starter
Member Since: Jan 2012
Location: Cin City
Posts: 4,885
Received 481 Likes
on
317 Posts
St. Jude Donor '14
July 14 Sale for Weapon7 splitter and rocker blades!!!!!!
Hi Guys,
We're running a special on our carbon splitter and rocker blades. These are American made and priced so competitively that even our carbon fiber rivals most fiberglass kits! They're made from the same molds and come gel coated ready to prep and paint. They use OEM mounting locations as well!
Composite splitters and rocker blades are $999 shipped!
Carbon Fiber splitters and rocker blades with clear coat are $1499 shipped!
Splitter - It has a nice lip across the front that tapers up and angles downward between the two fins on the lower front bumper lip so there's no awkward flat step up to try and bridge the gap. This space between the fins also provides some driveway relief! I know a couple of you guys were worried about the winglets on the side. They're in line with the tires and they're very short, so they blend in very well, but really draw some nice attention as well! It uses all OEM mounting bolt holes and if present, you can reattach your air deflectors under them if you wish.
Rocker blades - These run wheel to wheel and don't flare out until past the door line. We did this not only for style but to also keep the road rash off the bulging rear fenders. Again, these use all OEM bolt hole for mounting.
Enjoy the pics!
Notice the splitter and hood profile
side profile of splitter, rockers, and spoiler
Check out the splitter and hood profile!
The END
We're running a special on our carbon splitter and rocker blades. These are American made and priced so competitively that even our carbon fiber rivals most fiberglass kits! They're made from the same molds and come gel coated ready to prep and paint. They use OEM mounting locations as well!
Composite splitters and rocker blades are $999 shipped!
Carbon Fiber splitters and rocker blades with clear coat are $1499 shipped!
Splitter - It has a nice lip across the front that tapers up and angles downward between the two fins on the lower front bumper lip so there's no awkward flat step up to try and bridge the gap. This space between the fins also provides some driveway relief! I know a couple of you guys were worried about the winglets on the side. They're in line with the tires and they're very short, so they blend in very well, but really draw some nice attention as well! It uses all OEM mounting bolt holes and if present, you can reattach your air deflectors under them if you wish.
Rocker blades - These run wheel to wheel and don't flare out until past the door line. We did this not only for style but to also keep the road rash off the bulging rear fenders. Again, these use all OEM bolt hole for mounting.
Enjoy the pics!
Notice the splitter and hood profile
side profile of splitter, rockers, and spoiler
Check out the splitter and hood profile!
The END
Last edited by Ben@WeaponX; 08-10-2014 at 08:07 PM.
07-12-2014, 12:16 PM
#10
Safety Car
Thread Starter
Member Since: Jan 2012
Location: Cin City
Posts: 4,885
Received 481 Likes
on
317 Posts
St. Jude Donor '14
Just finished up Doug's complete kit yesterday! 
weapon7 splitter and blacked out grill bar
weapon7 rocker blades
rear rocker flared at rear fender
weapon7 spoiler
weapon7 splitter and blacked out grill bar
weapon7 rocker blades
rear rocker flared at rear fender
weapon7 spoiler
08-02-2014, 10:33 AM
#11
Le Mans Master
might have to get me this if I decide to drive the V in for a C7
You on CTSVowners.com?
11-04-2014, 01:50 AM
#16
Intermediate
Weapon X Web Site
Hi Guys,
We're running a special on our carbon splitter and rocker blades. These are American made and priced so competitively that even our carbon fiber rivals most fiberglass kits! They're made from the same molds and come gel coated ready to prep and paint. They use OEM mounting locations as well!
Composite splitters and rocker blades are $999 shipped!
Carbon Fiber splitters and rocker blades with clear coat are $1499 shipped!
Splitter - It has a nice lip across the front that tapers up and angles downward between the two fins on the lower front bumper lip so there's no awkward flat step up to try and bridge the gap. This space between the fins also provides some driveway relief! I know a couple of you guys were worried about the winglets on the side. They're in line with the tires and they're very short, so they blend in very well, but really draw some nice attention as well! It uses all OEM mounting bolt holes and if present, you can reattach your air deflectors under them if you wish.
Rocker blades - These run wheel to wheel and don't flare out until past the door line. We did this not only for style but to also keep the road rash off the bulging rear fenders. Again, these use all OEM bolt hole for mounting.
Enjoy the pics!
Notice the splitter and hood profile
side profile of splitter, rockers, and spoiler
Check out the splitter and hood profile!
The END
We're running a special on our carbon splitter and rocker blades. These are American made and priced so competitively that even our carbon fiber rivals most fiberglass kits! They're made from the same molds and come gel coated ready to prep and paint. They use OEM mounting locations as well!
Composite splitters and rocker blades are $999 shipped!
Carbon Fiber splitters and rocker blades with clear coat are $1499 shipped!
Splitter - It has a nice lip across the front that tapers up and angles downward between the two fins on the lower front bumper lip so there's no awkward flat step up to try and bridge the gap. This space between the fins also provides some driveway relief! I know a couple of you guys were worried about the winglets on the side. They're in line with the tires and they're very short, so they blend in very well, but really draw some nice attention as well! It uses all OEM mounting bolt holes and if present, you can reattach your air deflectors under them if you wish.
Rocker blades - These run wheel to wheel and don't flare out until past the door line. We did this not only for style but to also keep the road rash off the bulging rear fenders. Again, these use all OEM bolt hole for mounting.
Enjoy the pics!
Notice the splitter and hood profile
side profile of splitter, rockers, and spoiler
Check out the splitter and hood profile!
The END
