[Z06] Halltech MF103 Super Bee Sale
#22
Supporting Vendor
Thread Starter
Member Since: Jun 2005
Location: Marietta Georgia
Posts: 20,644
Received 315 Likes
on
288 Posts
St. Jude Donor '06-'07, '13, '15
#25
Does this mean that it comes with the beehive that's linked to in a couple of posts above?
While supplies last....469.99 shipped. with a free set of tailight seals (another 24.99 savings).
The Halltech Super Bee is for the C6 Z06 and the C6 LS3 (2008+_models) and is one of the few intakes that does not require cutting up the engine bay or tuning while still providing a 10-15 rwhp power gain.
The intake comes with the Beehive heatshield and everything needed to complete the installation (except the hand tools )
This is one of the easiest and warranty friendly ways to give your Vette a bolt on power gain without any permanent modifications or needing to tune.
More info, installation video, and ordering info here...
Halltech Super Bee MF103
Sale will last until we run out of stock.
Act quick, I do not think you will find a better deal anywhere on one of the best intakes for the C6.
The Halltech Super Bee is for the C6 Z06 and the C6 LS3 (2008+_models) and is one of the few intakes that does not require cutting up the engine bay or tuning while still providing a 10-15 rwhp power gain.
The intake comes with the Beehive heatshield and everything needed to complete the installation (except the hand tools )
This is one of the easiest and warranty friendly ways to give your Vette a bolt on power gain without any permanent modifications or needing to tune.
More info, installation video, and ordering info here...
Halltech Super Bee MF103
Sale will last until we run out of stock.
Act quick, I do not think you will find a better deal anywhere on one of the best intakes for the C6.
#28
Supporting Vendor
Thread Starter
Member Since: Jun 2005
Location: Marietta Georgia
Posts: 20,644
Received 315 Likes
on
288 Posts
St. Jude Donor '06-'07, '13, '15
While supplies last....455.99 shipped. with a free set of tail light seals.
The Halltech Super Bee is for the C6 Z06 and the C6 LS3 (2008+_models) and is one of the few intakes that does not require cutting up the engine bay or tuning while still providing a 10-15 rwhp power gain.
The intake comes with the Beehive heatshield and everything needed to complete the installation (except the hand tools )
This is one of the easiest and warranty friendly ways to give your Vette a bolt on power gain without any permanent modifications or needing to tune.
More info, installation video, and ordering info here...
Halltech Super Bee MF103
Sale will last until we run out of stock.
Act quick, I do not think you will find a better deal anywhere on one of the best intakes for the C6.
The Halltech Super Bee is for the C6 Z06 and the C6 LS3 (2008+_models) and is one of the few intakes that does not require cutting up the engine bay or tuning while still providing a 10-15 rwhp power gain.
The intake comes with the Beehive heatshield and everything needed to complete the installation (except the hand tools )
This is one of the easiest and warranty friendly ways to give your Vette a bolt on power gain without any permanent modifications or needing to tune.
More info, installation video, and ordering info here...
Halltech Super Bee MF103
Sale will last until we run out of stock.
Act quick, I do not think you will find a better deal anywhere on one of the best intakes for the C6.
#29
While supplies last....455.99 shipped. with a free set of tail light seals.
The Halltech Super Bee is for the C6 Z06 and the C6 LS3 (2008+_models) and is one of the few intakes that does not require cutting up the engine bay or tuning while still providing a 10-15 rwhp power gain.
The intake comes with the Beehive heatshield and everything needed to complete the installation (except the hand tools )
This is one of the easiest and warranty friendly ways to give your Vette a bolt on power gain without any permanent modifications or needing to tune.
More info, installation video, and ordering info here...
Halltech Super Bee MF103
Sale will last until we run out of stock.
Act quick, I do not think you will find a better deal anywhere on one of the best intakes for the C6.
The Halltech Super Bee is for the C6 Z06 and the C6 LS3 (2008+_models) and is one of the few intakes that does not require cutting up the engine bay or tuning while still providing a 10-15 rwhp power gain.
The intake comes with the Beehive heatshield and everything needed to complete the installation (except the hand tools )
This is one of the easiest and warranty friendly ways to give your Vette a bolt on power gain without any permanent modifications or needing to tune.
More info, installation video, and ordering info here...
Halltech Super Bee MF103
Sale will last until we run out of stock.
Act quick, I do not think you will find a better deal anywhere on one of the best intakes for the C6.
#33
Supporting Vendor
Member Since: Mar 2002
Location: Bristol, Tennessee
Posts: 12,988
Received 583 Likes
on
313 Posts
St. Jude Donor '09
Both are made from the same mold; the difference is the amount of wall thickness which allows us to dial in the MAF read area. That determines whether or not the intake can be installed without re-translation of the MAF tables.
In the case of the 103, it translates like stock with 3% unreported airflow, the MF105 around 5%. That helps bring a leaner WOT or Open Loop air fuel ratio. Kinda like tuning, but without touching the ECM.
Any leaner, and you would put too much unreported air into open loop, causing knock retard, which ends up costing the very horsepower you just gained.
In any case, the 103mm area is 13mm larger than the throttle body, so going larger only changes the way the MAF reads the airflow.
In the case of the 103, it translates like stock with 3% unreported airflow, the MF105 around 5%. That helps bring a leaner WOT or Open Loop air fuel ratio. Kinda like tuning, but without touching the ECM.
Any leaner, and you would put too much unreported air into open loop, causing knock retard, which ends up costing the very horsepower you just gained.
In any case, the 103mm area is 13mm larger than the throttle body, so going larger only changes the way the MAF reads the airflow.
__________________
"World Class Performance for your Corvette"
Intake Design and Engineering since 1999
Halltech Systems, LLC
262-510-7600
For service email:
orders@halltechsystems.com
www.halltechsystems.com
"World Class Performance for your Corvette"
Intake Design and Engineering since 1999
Halltech Systems, LLC
262-510-7600
For service email:
orders@halltechsystems.com
www.halltechsystems.com
#35
Melting Slicks
Sounds out of sequence, (to me anyway, Im sure you had a good reason).
Steve
#36
Instructor
While supplies last....499 shipped. with a free set of tail light seals.
The Halltech Super Bee is for the C6 Z06 and the C6 LS3 (2008+_models) and is one of the few intakes that does not require cutting up the engine bay or tuning while still providing a 10-15 rwhp power gain.
The intake comes with the Beehive heatshield and everything needed to complete the installation (except the hand tools )
This is one of the easiest and warranty friendly ways to give your Vette a bolt on power gain without any permanent modifications or needing to tune.
More info, installation video, and ordering info here...
Halltech Super Bee MF103
Sale will last until we run out of stock.
Act quick, I do not think you will find a better deal anywhere on one of the best intakes for the C6.
The Halltech Super Bee is for the C6 Z06 and the C6 LS3 (2008+_models) and is one of the few intakes that does not require cutting up the engine bay or tuning while still providing a 10-15 rwhp power gain.
The intake comes with the Beehive heatshield and everything needed to complete the installation (except the hand tools )
This is one of the easiest and warranty friendly ways to give your Vette a bolt on power gain without any permanent modifications or needing to tune.
More info, installation video, and ordering info here...
Halltech Super Bee MF103
Sale will last until we run out of stock.
Act quick, I do not think you will find a better deal anywhere on one of the best intakes for the C6.
If you ship to Southern Ontario Canada, then im in!
#38
Le Mans Master
Carbon Edition
While supplies last....499 shipped. with a free set of tail light seals.
The Halltech Super Bee is for the C6 Z06 and the C6 LS3 (2008+_models) and is one of the few intakes that does not require cutting up the engine bay or tuning while still providing a 10-15 rwhp power gain.
The intake comes with the Beehive heatshield and everything needed to complete the installation (except the hand tools )
This is one of the easiest and warranty friendly ways to give your Vette a bolt on power gain without any permanent modifications or needing to tune.
More info, installation video, and ordering info here...
Halltech Super Bee MF103
Sale will last until we run out of stock.
Act quick, I do not think you will find a better deal anywhere on one of the best intakes for the C6.
The Halltech Super Bee is for the C6 Z06 and the C6 LS3 (2008+_models) and is one of the few intakes that does not require cutting up the engine bay or tuning while still providing a 10-15 rwhp power gain.
The intake comes with the Beehive heatshield and everything needed to complete the installation (except the hand tools )
This is one of the easiest and warranty friendly ways to give your Vette a bolt on power gain without any permanent modifications or needing to tune.
More info, installation video, and ordering info here...
Halltech Super Bee MF103
Sale will last until we run out of stock.
Act quick, I do not think you will find a better deal anywhere on one of the best intakes for the C6.
#40
Supporting Vendor
Thread Starter
Member Since: Jun 2005
Location: Marietta Georgia
Posts: 20,644
Received 315 Likes
on
288 Posts
St. Jude Donor '06-'07, '13, '15
Hey guys,
Anyone interested in an intake comparison might want to check this out:
Cold-Air intake comparison
Thanks,
Dave
Anyone interested in an intake comparison might want to check this out:
Cold-Air intake comparison
Thanks,
Dave