View Poll Results: Would you be interested in these tips if the price is right?
Multiple Choice Poll. Voters: 43. You may not vote on this poll
[Z06] Halltech Carbon Fiber exhaust tips for the Akrapovic Exhaust
#21
Supporting Vendor
Thread Starter
Member Since: Mar 2002
Location: Bristol, Tennessee
Posts: 12,986
Received 582 Likes
on
312 Posts
St. Jude Donor '09
2nd tip installed today
The purple is the ceramic grease I used to adjust the tip.
I think they look incredible!
The purple is the ceramic grease I used to adjust the tip.
I think they look incredible!
__________________
"World Class Performance for your Corvette"
Intake Design and Engineering since 1999
Halltech Systems, LLC
262-510-7600
For service email:
orders@halltechsystems.com
www.halltechsystems.com
"World Class Performance for your Corvette"
Intake Design and Engineering since 1999
Halltech Systems, LLC
262-510-7600
For service email:
orders@halltechsystems.com
www.halltechsystems.com
Last edited by Halltech; 03-17-2012 at 05:02 PM.
#22
Instructor
Member Since: Oct 2011
Location: Youngsville La
Posts: 229
Likes: 0
Received 0 Likes
on
0 Posts
#26
Supporting Vendor
Thread Starter
Member Since: Mar 2002
Location: Bristol, Tennessee
Posts: 12,986
Received 582 Likes
on
312 Posts
St. Jude Donor '09
We do have permission though to make the C6.RS Carbon radiator bezel:
The mold for this is at our carbon fiber shop, and has been sitting there in a back room unused. They have now given us permission to use the mold for the C6 Corvette crowd. Only one made at a time. 1 in stock:
http://www.halltechsystems.com/product_p/pmrbc.htm
Last edited by Halltech; 03-18-2012 at 12:38 PM.
#27
Supporting Vendor
Thread Starter
Member Since: Mar 2002
Location: Bristol, Tennessee
Posts: 12,986
Received 582 Likes
on
312 Posts
St. Jude Donor '09
Straighter picture. I must be getting old. What looks like a straight shot ends up at about 2 degrees off every time. Thanks for the Photoshop job!
#28
Instructor
How will they handle the heat since they are directly connected to the pipe (unlike Akrapovic). Would these work on stock Z06 mufflers?
#29
Supporting Vendor
Thread Starter
Member Since: Mar 2002
Location: Bristol, Tennessee
Posts: 12,986
Received 582 Likes
on
312 Posts
St. Jude Donor '09
I wanted to give people a preview while you worked on the other two. I was also curious about what they would look like on my car so...
How will they handle the heat since they are directly connected to the pipe (unlike Akrapovic). Would these work on stock Z06 mufflers?
How will they handle the heat since they are directly connected to the pipe (unlike Akrapovic). Would these work on stock Z06 mufflers?
I took the temp at idle for 15 minutes on a 36F degree day-56F at the carbon fiber.
No worries at all. They will fit 2.55" o.d. tips.
#30
Instructor
#31
Advanced
Member Since: Dec 2006
Location: Orange County CA
Posts: 95
Likes: 0
Received 0 Likes
on
0 Posts
Nice work Jim.
I've been kicking around a couple of different exhausts for my ZR1 but could never get excited about the Akrapovic due to the tips. I'll do a little price shopping for a set of slip ons, and may need to take you up on a set. These make all the difference for me...
Sparky
I've been kicking around a couple of different exhausts for my ZR1 but could never get excited about the Akrapovic due to the tips. I'll do a little price shopping for a set of slip ons, and may need to take you up on a set. These make all the difference for me...
Sparky
#32
Drifting
We'll have the other two done by Wednesday. Each one takes curing at 375F for 9 hours. The special carbon fiber is the same material used on the Pratt and Miller Daytona coil covers. Wish I could show them to you, but they are not ours to show off.
We do have permission though to make the C6.RS Carbon radiator bezel:
The mold for this is at our carbon fiber shop, and has been sitting there in a back room unused. They have now given us permission to use the mold for the C6 Corvette crowd. Only one made at a time. 1 in stock:
http://www.halltechsystems.com/product_p/pmrbc.htm
We do have permission though to make the C6.RS Carbon radiator bezel:
The mold for this is at our carbon fiber shop, and has been sitting there in a back room unused. They have now given us permission to use the mold for the C6 Corvette crowd. Only one made at a time. 1 in stock:
http://www.halltechsystems.com/product_p/pmrbc.htm
Gary
#33
Supporting Vendor
Thread Starter
Member Since: Mar 2002
Location: Bristol, Tennessee
Posts: 12,986
Received 582 Likes
on
312 Posts
St. Jude Donor '09
Nice work Jim.
I've been kicking around a couple of different exhausts for my ZR1 but could never get excited about the Akrapovic due to the tips. I'll do a little price shopping for a set of slip ons, and may need to take you up on a set. These make all the difference for me...
Sparky
I've been kicking around a couple of different exhausts for my ZR1 but could never get excited about the Akrapovic due to the tips. I'll do a little price shopping for a set of slip ons, and may need to take you up on a set. These make all the difference for me...
Sparky
They are actually the same size as 90% of the aftermarket SS tips.
#34
Supporting Vendor
Thread Starter
Member Since: Mar 2002
Location: Bristol, Tennessee
Posts: 12,986
Received 582 Likes
on
312 Posts
St. Jude Donor '09
Stuck the last two on yesterday. Not perfectly lined up yet, but not bonded either:
First and last 4 for a while. We are not going to be making these any time soon. Too many other carbon fiber products to get out, and really not enough interest for us to make more molds required for production.
Saved 5.4 lbs vs. the Akrapovic Titanium 5" tips.
First and last 4 for a while. We are not going to be making these any time soon. Too many other carbon fiber products to get out, and really not enough interest for us to make more molds required for production.
Saved 5.4 lbs vs. the Akrapovic Titanium 5" tips.
#39
Supporting Vendor
Thread Starter
Member Since: Mar 2002
Location: Bristol, Tennessee
Posts: 12,986
Received 582 Likes
on
312 Posts
St. Jude Donor '09
Not enough interest to keep the molds in our shop. we could reprice them and quote them next week.
Still on our car and not yellow. Two flew off during racing so we now use lightweight clamps.
Still on our car and not yellow. Two flew off during racing so we now use lightweight clamps.
#40
Burning Brakes