[Z06] What are your Z #'s and with what mods?
#21
Melting Slicks
Thread Starter
Member Since: Dec 2002
Location: Lone Star State
Posts: 2,898
Likes: 0
Received 0 Likes
on
0 Posts
Never plan to take my car to the track but with a set of drag radials, I would be willing to say that the car will go 10.80s in the 1/4. Shawn can chime in to verify this since he's done several set ups with these #s.
Keep this going guys!!!!
Keep this going guys!!!!
#22
Advanced
Member Since: Jul 2005
Location: Manassas Va
Posts: 50
Likes: 0
Received 0 Likes
on
0 Posts
Mods
Procharger sc-1 at 6# boost LG C7X3 cam Melrose headers, x pipe & high flow cats, Fusion exhaust, Cooling mist meth injection 160 stat, MGW short throw shifter, Dewitt radiator, Pratt Miller Seats and steering wheel, tune, door panels, console cover, shifter and e-brake boots by DSvettes, dash, sun visiors, glove door,and knee booster on order. 703rwhp
#24
Advanced
Member Since: Jul 2005
Location: Manassas Va
Posts: 50
Likes: 0
Received 0 Likes
on
0 Posts
Drag times
With Pirelli p zero 345/25ZR20 on the rear and 275/30Zr19on the front could not hold traction. hope to get drag radials on 18" wheels this Spring. Best times with a+2 second 60 ft was 11.9 at 123mph not a garage queen it has 33,500 miles on the speedo
#26
Instructor
Member Since: Nov 2007
Location: Calgary Alberta
Posts: 118
Likes: 0
Received 0 Likes
on
0 Posts
700/700 - RWHP & TQ - JE forged pistons, Callies forged steel crank, Manley forged rods, stainless steel valves, balanced rotating assembly, blueprinted engine, fuel injectors and high capacity fuel system, port matched intake, ported and polished throttle body, twin Garrett BB turbos with integral waste gates, twin intercoolers, custom stainless steel 4 into 1 exhaust manifolds & turbo outlets, turbo scavenge pump & turbo oil drain reservoir, oil cooler, dual 4" Corsa stainless steel cat back exhaust, Exedy twin disc clutch and aluminum flywheel.
A little out of the way shop called Lingenfelter did the install.
A little out of the way shop called Lingenfelter did the install.
#27
Racer
Member Since: Dec 2007
Location: Fresh Meadows NY
Posts: 289
Likes: 0
Received 0 Likes
on
0 Posts
Mine is a vette doctors Stage 2 kit with cam, AR headers, ported intake and TB, milled heads, spring, retainers, CA honker. It puts down 572rwhp and 503RWTQ. I have taken the car to the track only twice and so far the best time I ran was 11.070 at almost 134mph. I the drag radials were overwhelmed by the power so I need to find and new wheel and tires selection. Right now the car is getting a dual disc clutch and some other trany upgrades. With new tires I am shooting for low 10's come spring time.
#29
Drifting
Mine is a vette doctors Stage 2 kit with cam, AR headers, ported intake and TB, milled heads, spring, retainers, CA honker. It puts down 572rwhp and 503RWTQ. I have taken the car to the track only twice and so far the best time I ran was 11.070 at almost 134mph. I the drag radials were overwhelmed by the power so I need to find and new wheel and tires selection. Right now the car is getting a dual disc clutch and some other trany upgrades. With new tires I am shooting for low 10's come spring time.
Thanks for the data mine was modded by the Vette doctors as well and made about 20- 30 RWHP so it should go a little slower around 131.5-132 or so. Plenty fast enough for me
#30
552 RWHP/521 RWTQ
Mods Completed:
Comp Cams custom grind
Ported TB/Intake
Ferrea Titanium Valves
Harland Sharp Rockers
Comp 921 springs w .030 shims on exhaust side
Lingenfelter CAI
American Racing Headers w/ High Flow Cats
Modified Factory Exhaust, M2W
Tune
Pfadt Coil Overs
Pfadt Street Sways
RPS Street Twin Disc Clutch
MGW Short Throw Shifter
Superficial Mods:
Caravaggio Steering Wheel, Airbag Cover, Handbrake, Shiftboot and ****
Repaint (had to get rid of the crappy factory paint job)
360 Forged Mesh 8's - on the way
Mods on the way:
Ported and Milled Heads
ARE Stage 2 Dry Sump System
Damn this thing is fun to work on!!!!!
Mods Completed:
Comp Cams custom grind
Ported TB/Intake
Ferrea Titanium Valves
Harland Sharp Rockers
Comp 921 springs w .030 shims on exhaust side
Lingenfelter CAI
American Racing Headers w/ High Flow Cats
Modified Factory Exhaust, M2W
Tune
Pfadt Coil Overs
Pfadt Street Sways
RPS Street Twin Disc Clutch
MGW Short Throw Shifter
Superficial Mods:
Caravaggio Steering Wheel, Airbag Cover, Handbrake, Shiftboot and ****
Repaint (had to get rid of the crappy factory paint job)
360 Forged Mesh 8's - on the way
Mods on the way:
Ported and Milled Heads
ARE Stage 2 Dry Sump System
Damn this thing is fun to work on!!!!!
Last edited by dfinke23; 12-23-2008 at 01:46 AM.
#31
580rwhp 514rwtq, cartek stage 2 cam, vararam, kooks headers w/ cats, b&b bullets, ported tb and intake, ported heads, tuned and installed by www.redline-motorsports.net
n20 #'s to come!!!!
n20 #'s to come!!!!
#32
Supporting Vendor
Our Stage 3 packages will run 10's. Stalker or Lethal.
Check out the fast list-
Engine Mods plus Bolt-Ons ------*Current Avg. 10.901 secs. @ 129.95 mph
1--10.525 @132.71--1.57---07WhiteDevilZ------'07 -------Details
2--10.629 @130.91--1.59--- MR Z-----'06 -----Details
3--10.695 @130.52--1.57---zmanz-----'06 -----Details
4--10.880 @130.94--1.77---layjzay-----'06 ------Details
Mr Z- Lethal Cam Stage 3
Layjzay-Stalker Cam Stage 3
Videos-
http://www.youtube.com/watch?v=Pbglo-IUtD0
http://www.youtube.com/watch?v=EDXHHTRCcs0
__________________
RAGIN’ RACIN’
Randy Leger
337-278-8397
sales@raginracin.com
http://www.raginracin.com
RAGIN’ RACIN’
Randy Leger
337-278-8397
sales@raginracin.com
http://www.raginracin.com
#33
Race Director
engine internals are stock, halltech intake, kooks headers, BB exhaust
PLUS 2 new large oil coolers boost my oil capacity 50% to 13 quarts and a new radiator from breathless mean I can run at 6500 rpm all day long at the track
PLUS 2 new large oil coolers boost my oil capacity 50% to 13 quarts and a new radiator from breathless mean I can run at 6500 rpm all day long at the track
#35
Melting Slicks
2007 Z
Vette-air, K&N Air intake, Ported Intake and TB, QM600, American Racing headers, Bullets, EWP, HP Tuners tune 565rwhp 505rwtq.
Last time at the track on DOT radials.
60'............. 1.890
330'........... 4.914
660'........... 7.341
660’ mph... 102.6
1000'.......... 9.361
1320'.......... 11.004
1320’ mph… 132.900
R.
Vette-air, K&N Air intake, Ported Intake and TB, QM600, American Racing headers, Bullets, EWP, HP Tuners tune 565rwhp 505rwtq.
Last time at the track on DOT radials.
60'............. 1.890
330'........... 4.914
660'........... 7.341
660’ mph... 102.6
1000'.......... 9.361
1320'.......... 11.004
1320’ mph… 132.900
R.