**RSD Bolt In NHRA Legal Roll Bar**
#41
Race Director
thanks Steve... i read it in the general section after i posted, i wish someone from the forum would have won, christopher has worked hard building that car and really deserved it, do you have any pics of how the sidebar bolts to the floor or kick panel
#42
Le Mans Master
Thread Starter
underside with stainless steal backing plate
Last edited by Steve@RSD; 09-21-2010 at 01:19 AM.
#43
Le Mans Master
That side bar looks different than the one RichieRichZ06 has in his. The curve part to swing out and clear the rockers seems to be straight. This would make more interior room. Is this the case?
#44
Race Director
#46
Supporting Vendor
Member Since: Nov 2005
Location: Supporting the Corvette Community at Abel Chevrolet in Rio Vista, CA 707-374-6317 Ext.123
Posts: 14,498
Received 1,426 Likes
on
597 Posts
St. Jude Donor '08
This car in Steves pics was the very first "test fit" and they adjusted the bends in the bar so that it cleared the door a little more by the time mine was being made. His clearance from the bar to the door was less then a sheet of paper and if the bar was not pinned in, it would contact the door and make a mark on it. On my car, they adjusted the bend so that it cleared more, causing a little closer fitment to the steering wheel and my legs. With it beig removable, there is no issue for street driving and little concern when racing. My leg just touches the bar, but does not interfere with launching or shifting.
hope that helps!
RICH
#47
Le Mans Master
Thread Starter
We already have sold the next three to come out of powder coating. Better get your order in now before my builder has a nervous breakdown! I told him this Corvette community needed this!
Three Vettes passed tech with flying colors this last weekend with the RSD Roll Bar at Pinks All Out at Infineon Raceway! 2 of the three were 10 second cars!
Steve@racespecialtydesigns.com
Three Vettes passed tech with flying colors this last weekend with the RSD Roll Bar at Pinks All Out at Infineon Raceway! 2 of the three were 10 second cars!
Steve@racespecialtydesigns.com
#48
Melting Slicks
Member Since: Jun 2009
Location: Naperville/Palm Beach IL/FL
Posts: 3,109
Likes: 0
Received 3 Likes
on
3 Posts
Steve,
Can you get a pic from the passenger side towards the drivers seat where the side bar comes down the door and steering wheel?
A few different angles please.
Also maybe one sitting in the drivers seat to show the room.
I am 6'3 and concerned for room.
Thanks in advance
Drew
Can you get a pic from the passenger side towards the drivers seat where the side bar comes down the door and steering wheel?
A few different angles please.
Also maybe one sitting in the drivers seat to show the room.
I am 6'3 and concerned for room.
Thanks in advance
Drew
#49
Le Mans Master
Thread Starter
Steve,
Can you get a pic from the passenger side towards the drivers seat where the side bar comes down the door and steering wheel?
A few different angles please.
Also maybe one sitting in the drivers seat to show the room.
I am 6'3 and concerned for room.
Thanks in advance
Drew
Can you get a pic from the passenger side towards the drivers seat where the side bar comes down the door and steering wheel?
A few different angles please.
Also maybe one sitting in the drivers seat to show the room.
I am 6'3 and concerned for room.
Thanks in advance
Drew
I have all those pics, send me you email adress and I can send them.
Passenger side;
With driver seated
Steve
#51
Le Mans Master
Thread Starter
#53
Le Mans Master
Thread Starter
Taking Orders Now, we just had a batch come back fropm Powder Coating this week and they look great!
Order Yours today! $1150 + Shipping for the 5 Point.
See Them Here; http://www.racespecialtydesigns.com/...&cat=85&page=1
PM or Email me your Zip Code for shipping rates.
Steve@RaceSpecialtyDesigns.com
Order Yours today! $1150 + Shipping for the 5 Point.
See Them Here; http://www.racespecialtydesigns.com/...&cat=85&page=1
PM or Email me your Zip Code for shipping rates.
Steve@RaceSpecialtyDesigns.com
Last edited by Steve@RSD; 10-12-2010 at 03:40 PM.
#54
hey steve, are the two rear bars and the two front bars only sandwiched to the floor pan with the plates? the main hoop looks to be bolted to a solid frame member, just wondering about the others. thanks
#55
Le Mans Master
Thread Starter
It is right out of the NHRA rule book.
Steve@RaceSpecialtyDesigns.com
#56
Le Mans Master
Thread Starter
Taking Orders Now, we just had a batch come back fropm Powder Coating this week and they look great!
Order Yours today! $1150 + Shipping for the 5 Point.
We have NHRA Legal Roll Bars for C6, C6Z06, C5, and C5Z06!! That's Right they fit the C5Z06! Come and Gettem we are shipping now, get yours here!
See Them Here; http://www.racespecialtydesigns.com/...&cat=85&page=1
PM or Email me your Zip Code for shipping rates.
Steve@RaceSpecialtyDesigns.com
Order Yours today! $1150 + Shipping for the 5 Point.
We have NHRA Legal Roll Bars for C6, C6Z06, C5, and C5Z06!! That's Right they fit the C5Z06! Come and Gettem we are shipping now, get yours here!
See Them Here; http://www.racespecialtydesigns.com/...&cat=85&page=1
PM or Email me your Zip Code for shipping rates.
Steve@RaceSpecialtyDesigns.com
#59
Le Mans Master
Thread Starter
......and if the color wasn't right you would not be happy and I would be stuck with a red one.
You could just get it from me in black, take it to your powder coater, and have them sandblast off the black and have them make it Victory red. It probably would only cost you $100 and you would have the custom roll bar you want.
I don't mean to sound negative, I just know you have options. I also will not send them uncoated.
Good Luck,
Steve
You could just get it from me in black, take it to your powder coater, and have them sandblast off the black and have them make it Victory red. It probably would only cost you $100 and you would have the custom roll bar you want.
I don't mean to sound negative, I just know you have options. I also will not send them uncoated.
Good Luck,
Steve
#60
Le Mans Master
Thread Starter
These are selling well, faster than my Chassis builder can build them. We have 4 coming out of powder coiating tomorrow and shipping Tuesday. 1 of them is yet unclaimed, Who's next?
Steve@racespecialtydesigns.com
Steve@racespecialtydesigns.com