RHS 427 build with F1X & Arun cam in it
#1
Team Owner
Thread Starter
Member Since: Jan 2007
Location: cookeville tennessee
Posts: 28,846
Received 1,762 Likes
on
1,529 Posts
RHS 427 build with F1X & Arun cam in it
Will be getting Kris, 02402ramair & Shane, z06wanted putting the new motor in the car this coming week. Kris & Shane has the motor and running gear out from under the car now. Robert
Last edited by robert miller; 02-25-2013 at 10:31 AM.
#4
Safety Car
#6
Safety Car
Good luck with your build Robert look forward to seeing how this turns out for you. What's the new fuel system consist of and what kinda bling are ya going to run for an intake?
Wasn't all that long ago that 650-700whp was a bunch now if your not turning 900+++ your not even in the game.
Pat
#7
Drifting
OK guys, I would like to help Robert out and give some of the details of this build. I will add as the build comes along. I have lots of pictures of before,during tear down & motor build pics. I am only posting a couple so everyone can see where we are at as of now.
This build was scheduled to start several months ago but without a motor there was no since in pulling it apart and taking up a rack while we wait on the engine. We still don't have a motor but have been promised it will ship this week.
Robert if you will e mail me all the engine specs and parts being used I will try to post them in English.
The basics are (will update with detailed info)
RHS 427
TFS 245's
Aruns custom cam
Fast 102 with 90mm TB
1200cc Injectors
Custom fuel system
F1x supercharger
Cartek bracket
ECS Intercooler and piping
Big red race valve
Coan 3 disk lockup converter
We are cleaning and painting everthing possible, fixing anything that could give Robert issue, remote fender mounting coils,removing any unnessary wiring from harnesses and so on. We have a long road ahead but the end result should be a 1000 plus rwhp car that can be driven anywhere in full street trim with good drivability and reliability and then be able to bolt some slicks on it and run bottom 9s to high 8's in the 1/4.
This build is overkill but doing so should decrease any chance of failures and increase the chance of obtaining his goals.
Video of car before teardown
Engine that is sold and getting ready to be shipped out
Fuel system that is sold and getting ready to be shipped out
This build was scheduled to start several months ago but without a motor there was no since in pulling it apart and taking up a rack while we wait on the engine. We still don't have a motor but have been promised it will ship this week.
Robert if you will e mail me all the engine specs and parts being used I will try to post them in English.
The basics are (will update with detailed info)
RHS 427
TFS 245's
Aruns custom cam
Fast 102 with 90mm TB
1200cc Injectors
Custom fuel system
F1x supercharger
Cartek bracket
ECS Intercooler and piping
Big red race valve
Coan 3 disk lockup converter
We are cleaning and painting everthing possible, fixing anything that could give Robert issue, remote fender mounting coils,removing any unnessary wiring from harnesses and so on. We have a long road ahead but the end result should be a 1000 plus rwhp car that can be driven anywhere in full street trim with good drivability and reliability and then be able to bolt some slicks on it and run bottom 9s to high 8's in the 1/4.
This build is overkill but doing so should decrease any chance of failures and increase the chance of obtaining his goals.
Video of car before teardown
Engine that is sold and getting ready to be shipped out
Fuel system that is sold and getting ready to be shipped out
#8
Team Owner
Thread Starter
Member Since: Jan 2007
Location: cookeville tennessee
Posts: 28,846
Received 1,762 Likes
on
1,529 Posts
Really, do ya read many of his post?
Good luck with your build Robert look forward to seeing how this turns out for you. What's the new fuel system consist of and what kinda bling are ya going to run for an intake?
Wasn't all that long ago that 650-700whp was a bunch now if your not turning 900+++ your not even in the game.
Pat
Good luck with your build Robert look forward to seeing how this turns out for you. What's the new fuel system consist of and what kinda bling are ya going to run for an intake?
Wasn't all that long ago that 650-700whp was a bunch now if your not turning 900+++ your not even in the game.
Pat
1) Magnafuel 4303 2000 hp fuel pump
2) -10 feed line and also -10 return line
3)Lunati pro billet I beam rods, lunati pro series forged crank
4)Meziere 55 gpm elec water pump
5) wiseco forged piston with bigger wrist pins & hellfire rings
6)trickflow 245 heads with Brain Tooley doing the work to them
7) Fast 102 ported intake, ported 90mm tb
8) Arun,s stage 4x cams in the car. Arun thanks for this little piece buddy..
9) kooks 2 inch coated headers
10) 3 bar now for kris to play with the tune on it:lol
11) Coan 3 disk converter
12)RPM Level VII trans
13) ragtopws6 z06 rear end with a 3:42 gear set up in it.
14) Plus got all my fuel set up from Jamie aka in here SMOOVE great guy in here to deal with.
Last edited by robert miller; 02-24-2013 at 10:30 PM.
#9
Safety Car
Pat, some give me a hard time in here & that is cool.
1) Magnafuel 4303 2000 hp fuel pump
2) -10 feed line and also -10 return line
3)Lunati pro billet I beam rods, lunati pro series forged crank
4)Meziere 55 gpm elec water pump
5) wiseco forged piston with bigger wrist pins & hellfire rings
6)trickflow 245 heads with Brain Tooley doing the work to them
7) Fast 102 ported intake, ported 90mm tb
8) Arun,s stage 4x cams in the car. Arun thanks for this little piece buddy..
9) kooks 2 inch coated headers
10) 3 bar now for kris to play with the tune on it:lol
11) Coan 3 disk converter
12)RPM Level VII trans
13) ragtopws6 z06 rear end with a 3:42 gear set up in it.
14) Plus got all my fuel set up from Jamie aka in here SMOOVE great guy in here to deal with.
1) Magnafuel 4303 2000 hp fuel pump
2) -10 feed line and also -10 return line
3)Lunati pro billet I beam rods, lunati pro series forged crank
4)Meziere 55 gpm elec water pump
5) wiseco forged piston with bigger wrist pins & hellfire rings
6)trickflow 245 heads with Brain Tooley doing the work to them
7) Fast 102 ported intake, ported 90mm tb
8) Arun,s stage 4x cams in the car. Arun thanks for this little piece buddy..
9) kooks 2 inch coated headers
10) 3 bar now for kris to play with the tune on it:lol
11) Coan 3 disk converter
12)RPM Level VII trans
13) ragtopws6 z06 rear end with a 3:42 gear set up in it.
14) Plus got all my fuel set up from Jamie aka in here SMOOVE great guy in here to deal with.
Subscribed,
Pat
#10
Team Owner
Thread Starter
Member Since: Jan 2007
Location: cookeville tennessee
Posts: 28,846
Received 1,762 Likes
on
1,529 Posts
Awesome build Robert and wish ya the best. One thing about your grammar, it's not good but the content is solid once ya add some punctuation. Ya have a good sense of humor and I get a kick out of reading our posts, that's why I bust your chops a bit, props!
Subscribed,
Pat
Subscribed,
Pat
Plus I know Kris is one hell of a tuner, also the same on ever step he does to a car. He and Shane will have it done in no time, and back on the road. Robert
#12
Drifting
I am guessing he is doing something secret to the glove box since it had been removed before delivery to me.
Mabe he is having one widdeled out of wood for the real wood grain effect.
Mabe he is having one widdeled out of wood for the real wood grain effect.
#13
Team Owner
Thread Starter
Member Since: Jan 2007
Location: cookeville tennessee
Posts: 28,846
Received 1,762 Likes
on
1,529 Posts
#14
Team Owner
Thread Starter
Member Since: Jan 2007
Location: cookeville tennessee
Posts: 28,846
Received 1,762 Likes
on
1,529 Posts
You where not to be telling all here kris. No on the glove box I sent it up to Dennis at DD he redone it for me in some of that sweet leather stuff that cost more $$$. But I do have it back now and it looks great.
#16
Team Owner
Thread Starter
Member Since: Jan 2007
Location: cookeville tennessee
Posts: 28,846
Received 1,762 Likes
on
1,529 Posts
I guess I couldnt put up a 9 in it now. But after you get done with it, and we go to the track we may be putting a 8 up.
Last edited by robert miller; 02-26-2013 at 08:51 AM.
#17
Le Mans Master
Not sure what you tried to said, but I think you should upgrade to the ECS Haltech ECU if you're gonna run it hard at the track.
#18
Safety Car
I wish you would of started your thread after it was dynoed. But on the other hand i'll miss all the comments that wouldn't be coming with a quick install dyno thread. I'm going to try my hardest to make it out to the racers coming up and meet some of you gear heads. Keep the up dates coming.
Last edited by helga203; 02-25-2013 at 06:45 AM.
#19
Team Owner
Nice build Robert!
That is going to be super wicked!
Subscribing for the updates!
Thanks,Matt
That is going to be super wicked!
Subscribing for the updates!
Thanks,Matt