FS: Built '99 FRC
12-06-2009, 04:28 PM
#1
Melting Slicks
Thread Starter
FS: Built '99 FRC
As much as I don’t want to do this... I have too much going on in my life to continue on with my car... so here it is! Im currently in Afghanistan working to pay off my house and get back into school so I need to get rid of this thing so I can get back home to my family. The car is flawless and runs like no other! I have a slew of mods so bare with me.
Here is my setup:
Cartek LS6 Stage 4X heads. Includes, full porting heads intake, exhaust, and combustion chamber, Manley severe duty stainless valves, 2.02 intake, 1.57 exhaust, seals, Manley dual springs, spring seats, seals, titanium retainers, milled .030.
Custom grind Cartek Stage 2X Cam computer verified.
228-232 582-598 116LSA
Cromoly hardened push rods.
Cometic heavy duty head gaskets.
ASP under drive pulley with belts.
Roll master dual roller timing chain.
Ported Z06 oil pump setup for the roll master.
FAST 3 piece intake manifold ported to 4X with a 90MM throttle opening.
Ported LS2 throttle body.
ECU Reprogram 97-2004 LS1 full dyno tune by Lethal Performance
Notch pistons for clearance.
Complete NX system includes, NX wet kit with 10# bottle, purge, MSD digital RPM window switch, timing retard module, custom switch panel with micro switches and LED lights, all wires, Bosch relays. Also includes, blow down tube, full throttle switch, Kenny Bell Boost-a-pump, and NGK BR7EF spark plugs.
Nitrous Outlets 860 Fully automated aluminum bottle heater
4.10 gears.
C5 passenger and driver side 300M output shaft with side gear.
C5 line lock kit includes pre-bent line with braided flex hose, inline line lock solenoid, and switch installed.
Vararam B2 intake
Vararam Power duct
GM Racing spark plug wires and NGK BR7EF plugs
160* thermostat
New Coolant crossover
CCA Red oil catch can
American Racing Headers (1 7/8 primaries 3" collector)
American Racing 3" X pipe
Borla Stinger 2.5" catback
Built T56 tranny by Lethal Performance
Hurst C6 short throw shifter
Spec III Clutch and Billet aluminum flywheel
Brand new Slave cylinder
Upgraded Tick Performance Master cylinder
Innovate LC1 Wideband
Lingenfelter LNC003 True Two step.
Cross drilled and slotted rotors on all four corners
Ceramic brake pads recently installed
Painted brake calipers.
CCW Big street Classics
275-40-18 Michelin Pilot Sports in the front (still brand new)
335-30-18 Nitto 555R Drag radials in the rear (almost out the door)
Tinted windows all around
The car makes 460 and 400 on motor and 632 and 525 on spray. The car has ran a best of 10.3 @ 136 with a 1.46 sixty foot. I did this with a 150 shot. I purposely built this car to run the quarter and since it has seen maybe 15 passes and that’s all. I believe with some fine tuning and more seat time the car could possibly see a very low 10 sec or high 9 on the stock bottom end and suspension... which are the only things on this car still stock.
I bought this car (as the second owner) from Corvette Palace in Austin TX with only 17,500 miles. It currently has 50500 on the clock. The car was completely stock all the way down to the stock rubber. The gentleman that owned it before me took very good care of the car. Since the purchase it has been purposely modded to run with perfection! The A/C still blows COLD and of course the heat still works. This car is still VERY streetable and can be used as a daily driver if need be. It has only seen the rain once and has been garage kept since day one. The oil is changed every 3000 miles or three months and after every race with Mobile1. The spark plugs are changed monthly or after every race. Its kept clean, waxed and garaged. The paint looks the same as it did when it rolled out of the factory paint booth. This car still sees 24-25 MPGs on the highway and never below 17 in the city.
Also a fairly new Corvette car cover I used to cover the car while I was in Iraq will be thrown into the deal.
I have invested over $50000 in this car to include payoff. I’m asking $23000 OBO. This car is worth every penny!
Pics of the car with the current CCW Big Street Classics:
Pics with my old rims:
Contact me at Jdanielm1@yahoo.com or call my wife at 254-368-0109 at any time. Serious inquiries only please!
Here is my setup:
Cartek LS6 Stage 4X heads. Includes, full porting heads intake, exhaust, and combustion chamber, Manley severe duty stainless valves, 2.02 intake, 1.57 exhaust, seals, Manley dual springs, spring seats, seals, titanium retainers, milled .030.
Custom grind Cartek Stage 2X Cam computer verified.
228-232 582-598 116LSA
Cromoly hardened push rods.
Cometic heavy duty head gaskets.
ASP under drive pulley with belts.
Roll master dual roller timing chain.
Ported Z06 oil pump setup for the roll master.
FAST 3 piece intake manifold ported to 4X with a 90MM throttle opening.
Ported LS2 throttle body.
ECU Reprogram 97-2004 LS1 full dyno tune by Lethal Performance
Notch pistons for clearance.
Complete NX system includes, NX wet kit with 10# bottle, purge, MSD digital RPM window switch, timing retard module, custom switch panel with micro switches and LED lights, all wires, Bosch relays. Also includes, blow down tube, full throttle switch, Kenny Bell Boost-a-pump, and NGK BR7EF spark plugs.
Nitrous Outlets 860 Fully automated aluminum bottle heater
4.10 gears.
C5 passenger and driver side 300M output shaft with side gear.
C5 line lock kit includes pre-bent line with braided flex hose, inline line lock solenoid, and switch installed.
Vararam B2 intake
Vararam Power duct
GM Racing spark plug wires and NGK BR7EF plugs
160* thermostat
New Coolant crossover
CCA Red oil catch can
American Racing Headers (1 7/8 primaries 3" collector)
American Racing 3" X pipe
Borla Stinger 2.5" catback
Built T56 tranny by Lethal Performance
Hurst C6 short throw shifter
Spec III Clutch and Billet aluminum flywheel
Brand new Slave cylinder
Upgraded Tick Performance Master cylinder
Innovate LC1 Wideband
Lingenfelter LNC003 True Two step.
Cross drilled and slotted rotors on all four corners
Ceramic brake pads recently installed
Painted brake calipers.
CCW Big street Classics
275-40-18 Michelin Pilot Sports in the front (still brand new)
335-30-18 Nitto 555R Drag radials in the rear (almost out the door)
Tinted windows all around
The car makes 460 and 400 on motor and 632 and 525 on spray. The car has ran a best of 10.3 @ 136 with a 1.46 sixty foot. I did this with a 150 shot. I purposely built this car to run the quarter and since it has seen maybe 15 passes and that’s all. I believe with some fine tuning and more seat time the car could possibly see a very low 10 sec or high 9 on the stock bottom end and suspension... which are the only things on this car still stock.
I bought this car (as the second owner) from Corvette Palace in Austin TX with only 17,500 miles. It currently has 50500 on the clock. The car was completely stock all the way down to the stock rubber. The gentleman that owned it before me took very good care of the car. Since the purchase it has been purposely modded to run with perfection! The A/C still blows COLD and of course the heat still works. This car is still VERY streetable and can be used as a daily driver if need be. It has only seen the rain once and has been garage kept since day one. The oil is changed every 3000 miles or three months and after every race with Mobile1. The spark plugs are changed monthly or after every race. Its kept clean, waxed and garaged. The paint looks the same as it did when it rolled out of the factory paint booth. This car still sees 24-25 MPGs on the highway and never below 17 in the city.
Also a fairly new Corvette car cover I used to cover the car while I was in Iraq will be thrown into the deal.
I have invested over $50000 in this car to include payoff. I’m asking $23000 OBO. This car is worth every penny!
Pics of the car with the current CCW Big Street Classics:
Pics with my old rims:
Contact me at Jdanielm1@yahoo.com or call my wife at 254-368-0109 at any time. Serious inquiries only please!
Last edited by JDaniel; 12-18-2010 at 08:03 PM. Reason: added to mod list
12-06-2009, 08:51 PM
#2
AMP Racing
Member Since: Aug 2006
Location: Washington TWP NJ
Posts: 10,450
Received 468 Likes
on
353 Posts
2023 C5 of the Year Finalist - Modified
2017 C5 of Year Finalist
St. Jude Donor '09-'10-'11-'12
UGH!!!
Brother, I cant believe you're selling your car...
I freakin LOVE those wheels.
It sure is a nice ride. GL with the sale.
Brother, I cant believe you're selling your car...
I freakin LOVE those wheels.
It sure is a nice ride. GL with the sale.
12-11-2009, 10:42 PM
#14
How much were those wheels? This is a good deal for someone looking for a modded vette.
12-12-2009, 01:44 PM
#15
Melting Slicks
Thread Starter
Well... these are not the current wheels on the car as ststed in the mod list. It has CCW Big Street Classics on it right now. I traded the CCW 505a for the Classics. However, the wheels alone are close to $3000 brand new. So if the buyer so chooses he could sell the wheels and make a $2500 profit right off the bat. I do have the stock wagon wheels that will go with the car if/whel sold.
Like I said before... I have reciepts for over $20,000 in mods and most of them were done by Cartek in NJ.
Like I said before... I have reciepts for over $20,000 in mods and most of them were done by Cartek in NJ.
