1993 Corvette coupe 6 speed, 88K
03-11-2012, 09:16 PM
#1
Heel & Toe
Thread Starter
Member Since: Aug 2009
Location: Fort Worth Texas
Posts: 18
Likes: 0
Received 0 Likes
on
0 Posts
1993 Corvette coupe 6 speed, 88K
SOLD
It's very clean and I've already taken care of most of the problems that C4's seem to have.
Here’s what I’ve done:
Rear suspension-all bushings replaced with polyurethane.
Rear hubs.
U joints (AC Delco) in half shafts and drive shaft.
Transmission, ZF 6 speed, blue tag. Brand new, not used , not rebuilt
Clutch, stock Valeo
Clutch slave cylinder, master cylinder and line.
Exhaust hangers.
Parking brake cables.
Fuel sending unit (gas gauge), fuel pump, fuel filter, all AC Delco.
Heater core
Radiator, new, AC Delco, nothing wrong with old one just got a good deal on a NOS
Radiator and heater hoses
Water pump, forgot brand but it is American made.
New MSD Optispark, coil, plug wires, spark plugs
Bosch III injectors, Idle air controller, MAP sensor, throttle position sensor, oxygen sensors
Fuel pressure regulator
Upgraded front brake to J55, 13”, new OEM rotors, braided brake lines, Hawk HPS pads. Also new rotors and HPS pads in rear. Also brake bias spring in master cylinder (Doug Rippie Motosports).
Headlight motors have new gears and bushings.
New radio antenna, AC Delco
Several new weatherstrips, but not all.
Alternator, 140 amp
Asking $9000
Has 93K miles now, don't know how to edit the top part.
Here's some pictures:
http://s68.photobucket.com/albums/i3...93%20Corvette/
It's very clean and I've already taken care of most of the problems that C4's seem to have.
Here’s what I’ve done:
Rear suspension-all bushings replaced with polyurethane.
Rear hubs.
U joints (AC Delco) in half shafts and drive shaft.
Transmission, ZF 6 speed, blue tag. Brand new, not used , not rebuilt
Clutch, stock Valeo
Clutch slave cylinder, master cylinder and line.
Exhaust hangers.
Parking brake cables.
Fuel sending unit (gas gauge), fuel pump, fuel filter, all AC Delco.
Heater core
Radiator, new, AC Delco, nothing wrong with old one just got a good deal on a NOS
Radiator and heater hoses
Water pump, forgot brand but it is American made.
New MSD Optispark, coil, plug wires, spark plugs
Bosch III injectors, Idle air controller, MAP sensor, throttle position sensor, oxygen sensors
Fuel pressure regulator
Upgraded front brake to J55, 13”, new OEM rotors, braided brake lines, Hawk HPS pads. Also new rotors and HPS pads in rear. Also brake bias spring in master cylinder (Doug Rippie Motosports).
Headlight motors have new gears and bushings.
New radio antenna, AC Delco
Several new weatherstrips, but not all.
Alternator, 140 amp
Asking $9000
Has 93K miles now, don't know how to edit the top part.
Here's some pictures:
http://s68.photobucket.com/albums/i3...93%20Corvette/
Last edited by theforthstooge; 01-02-2013 at 05:16 PM. Reason: remove trades accepted
03-12-2012, 01:20 PM
#3
Melting Slicks
"Asking $10,000 but open to offers. I know I won't get back what I've put into it but it's all about the fun, right?"
You have had a lot of fun my friend! This is an insane price that somebody should snap up soon. Very nice.
-Chris
You have had a lot of fun my friend! This is an insane price that somebody should snap up soon. Very nice.
-Chris
03-19-2012, 10:43 PM
#6
Instructor
Member Since: Oct 2010
Location: acadiana area Louisiana
Posts: 150
Likes: 0
Received 0 Likes
on
0 Posts
Sweet deal!!!! I think you're
for asking only this amount. I wouldn't come down at all. Someone will snap this up real fast. Sounds like a fun car with 6 speed!!
for asking only this amount. I wouldn't come down at all. Someone will snap this up real fast. Sounds like a fun car with 6 speed!!
03-19-2012, 11:03 PM
#7
Instructor
Member Since: Jan 2012
Location: Huntsville AL
Posts: 111
Likes: 0
Received 0 Likes
on
0 Posts
Yeah I'm having a big struggle right now - found a decent local well priced C3, but Andy has done a fantastic job on his 93 - he's put all the right gear in the right places to tighten it up - wish it was closer - still thinking on it
