1996 LT-1 Part out
10-13-2016, 02:49 PM
#85
Le Mans Master
does the fuel level sensor work?
How much for the full assembly out of the tank shipped to 30087?
How much for the full assembly out of the tank shipped to 30087?
10-14-2016, 09:27 PM
#86
Le Mans Master
Thread Starter
10-14-2016, 09:35 PM
#87
Le Mans Master
Thread Starter
Parts list and photos have been updated
ALL THAT'S LEFT. Car has been scraped.
Center console arm rest: $80 shipped
Red Floor Matts: $40 shipped
Driver Info Center: $75 shipped
(2) A/C programmers (under dash): $200 shipped ea.
Drivers side headlight assembly: $80 shipped (needs paint)
Stock radiator: $80 shipped
Red Silicone Radiator Hoses and clamps: $120 shipped
Fiberglass top: 300 + shipping (looking into pricing for paint match), no headliner for helmet clearance.
Gill panels: $60 shipped (pair)
Custom mesh license plate fill panel: $45 shipped
D36 complete rear end: Van Steel HD u-joints, heim toe bars, poly camber bars, fresh poly batwing bushings & poly control arm bushings (less than 3,000 miles), hawk HP+ pads, Van Steel lower coilover mounts seized onto knuckles, high speed 2.59 gear. $500 + shipping
Hood: $100 (local pick up only, Largo, FL)
Fog lights: $80 shipped, one has small crack. Can have professionally tinted at extra cost.
Rear side marker lights: $50 shipped (pair)
Custom C-beam plates: $75 shipped. Kept rear of car solid under hard acceleration (autocross).
I think I have some other misc parts and pieces laying around I'll add soon.
Center console arm rest: $80 shipped
Red Floor Matts: $40 shipped
Driver Info Center: $75 shipped
(2) A/C programmers (under dash): $200 shipped ea.
Drivers side headlight assembly: $80 shipped (needs paint)
Stock radiator: $80 shipped
Red Silicone Radiator Hoses and clamps: $120 shipped
Fiberglass top: 300 + shipping (looking into pricing for paint match), no headliner for helmet clearance.
Gill panels: $60 shipped (pair)
Custom mesh license plate fill panel: $45 shipped
D36 complete rear end: Van Steel HD u-joints, heim toe bars, poly camber bars, fresh poly batwing bushings & poly control arm bushings (less than 3,000 miles), hawk HP+ pads, Van Steel lower coilover mounts seized onto knuckles, high speed 2.59 gear. $500 + shipping
Hood: $100 (local pick up only, Largo, FL)
Fog lights: $80 shipped, one has small crack. Can have professionally tinted at extra cost.
Rear side marker lights: $50 shipped (pair)
Custom C-beam plates: $75 shipped. Kept rear of car solid under hard acceleration (autocross).
I think I have some other misc parts and pieces laying around I'll add soon.
10-17-2016, 09:55 PM
#89
Le Mans Master
Thread Starter
10-20-2016, 06:54 AM
#91
Le Mans Master
Thread Starter
All of the a/c vents are gone. I only have a handful of parts left from the car that I need to take photos of. The car was pretty well stripped and scrapped.
The following users liked this post:
BacknBlack08 (10-20-2016)
10-21-2016, 11:05 AM
#95
Le Mans Master
Thread Starter
10-22-2016, 09:35 AM
#96
Le Mans Master
Thread Starter
10-23-2016, 12:41 AM
#98
Le Mans Master
Thread Starter
I sure do. Pulling the ignition cylinder for the engine buyer. Clock spring, I'll see what I can do this week getting the column broken down.
