1991 Corvette parts (short block, wheels, driveline parts, etc)
#1
Racer
Thread Starter
1991 Corvette parts (short block, wheels, driveline parts, etc)
I've been working on a 1991 Corvette project and I've gathered up a lot of extra parts. It's time to clean out the garage.
1991 factory Corvette 5.7 liter (350) V8 "shortblock" (pistons, rods, cam, lifters, pushrods, timing chain, timing cover, crank, harmonic balancer). 117k miles on it, ran great and didn't smoke or use oil.
$250 local pickup only - SOLD
Corvette "J55" heavy duty brake caliper brackets (just add the correct calipers and rotors to upgrade to the 13" factory heavy duty brake kit).
$90 - SOLD
Accell 36 lb/hr injectors. Used, decent condition.
$85 - SOLD
Factory Dana 44 limited slip rebuild kit (Posi rebuild clutches and steels). New in the box.
$65 - SOLD
4 Heavy duty universal joints for the rear half shafts. New in the box.
$70
Spare aluminum rear half shafts (from a roughly '93 Corvette).
$65
Set of 4 17x9.5" machined finish "Sawblades" wheels with center caps.
$175 Local pickup only - SOLD
Set of 4 17x9.5" painted finish "Sawblades" wheels (no center caps). I bought these from someone who had them refinished and they were never used.
$325 Local pickup only
MSD Shift light (LED version that uses MSD rpm modules) and a set of RPM modules (6,100-6,900 rpm). Used, in very good condition (the mounting bracket was bent slightly to mount it on a roll cage tube, otherwise it's nearly new and only has about an hour of run time on it).
$75
Corvette "letters" for the molded in "CORVETTE" on the back of the 1991to 1996 Corvettes. Black letters with adhesive backing made out of a black finish material (I'm thinking it's a plastic, but they are still sealed in the package).
$25
6 speed Corvette rubber shift boot (the one that seals the shifter to the transmission tunnel, not the leather one inside the car). New in the box, aftermarket boot.
$40
Z51 factory road race/autocross springs for sale (Spring codes FHB and NYU). I have a Z51 front spring that I gathered up for my 1991 Corvette project but never installed. It is a used spring, but in very good condition. I've decided to stick to part out my project car, so I'm offering it for sale. The front spring is marked FHB. It has no wedges and the rubber bushings have been trimmed.
Pics on request.
$95 plus freight OBO (FHB spring is SOLD)
I also have a rear Z51spring (code NYU) that has stock spacers on it, used but in good condition.
$95 OBO
Pics on request.
trackbird (at) gmail dot com
1991 factory Corvette 5.7 liter (350) V8 "shortblock" (pistons, rods, cam, lifters, pushrods, timing chain, timing cover, crank, harmonic balancer). 117k miles on it, ran great and didn't smoke or use oil.
$250 local pickup only - SOLD
Corvette "J55" heavy duty brake caliper brackets (just add the correct calipers and rotors to upgrade to the 13" factory heavy duty brake kit).
$90 - SOLD
Accell 36 lb/hr injectors. Used, decent condition.
$85 - SOLD
Factory Dana 44 limited slip rebuild kit (Posi rebuild clutches and steels). New in the box.
$65 - SOLD
4 Heavy duty universal joints for the rear half shafts. New in the box.
$70
Spare aluminum rear half shafts (from a roughly '93 Corvette).
$65
Set of 4 17x9.5" machined finish "Sawblades" wheels with center caps.
$175 Local pickup only - SOLD
Set of 4 17x9.5" painted finish "Sawblades" wheels (no center caps). I bought these from someone who had them refinished and they were never used.
$325 Local pickup only
MSD Shift light (LED version that uses MSD rpm modules) and a set of RPM modules (6,100-6,900 rpm). Used, in very good condition (the mounting bracket was bent slightly to mount it on a roll cage tube, otherwise it's nearly new and only has about an hour of run time on it).
$75
Corvette "letters" for the molded in "CORVETTE" on the back of the 1991to 1996 Corvettes. Black letters with adhesive backing made out of a black finish material (I'm thinking it's a plastic, but they are still sealed in the package).
$25
6 speed Corvette rubber shift boot (the one that seals the shifter to the transmission tunnel, not the leather one inside the car). New in the box, aftermarket boot.
$40
Z51 factory road race/autocross springs for sale (Spring codes FHB and NYU). I have a Z51 front spring that I gathered up for my 1991 Corvette project but never installed. It is a used spring, but in very good condition. I've decided to stick to part out my project car, so I'm offering it for sale. The front spring is marked FHB. It has no wedges and the rubber bushings have been trimmed.
Pics on request.
$95 plus freight OBO (FHB spring is SOLD)
I also have a rear Z51spring (code NYU) that has stock spacers on it, used but in good condition.
$95 OBO
Pics on request.
trackbird (at) gmail dot com
Last edited by trackbird; 08-31-2014 at 12:41 PM.
#3
Prices reduce by how much?
#4
Racer
Thread Starter
#5
Drifting
E-Mail sent
#7
Racer
Thread Starter
#11
Burning Brakes
Trackbird, I'm not sure my PM's have been going through??..I am interested in your shortblock and was wondering if you would be available sometime next week for me to come look at??
Thanks,
Tom S.
Thanks,
Tom S.