Dual Mass Flywheel, Clutch, New In Box
05-01-2014, 07:01 PM
#1
Racer
Thread Starter
Member Since: May 1999
Location: Nashville TN
Posts: 290
Likes: 0
Received 0 Likes
on
0 Posts
FS: Dual Mass Flywheel, Clutch, PP, New In Box
Hi all,
I'm selling a LuK dual mass flywheel, clutch disc, and Valeo pressure plate. All items are brand new in original boxes. Also included is a new pilot bearing, balancing weights, and clutch alignment tool. The flywheel is "unopened", still sealed in plastic to a piece of cardboard. The DMF will fit 89+ L98 and LT1/4, but the pressure plate is LT1/4 specific.
** 8/23/2014 EDIT **
The flywheel and pressure plate have been sold. I still have the clutch disc and throwout bearing. They are both aftermarket pieces. I'll take $100 shipped for both.
Let me know if interested!
** END EDIT **
Photos:
I'm selling a LuK dual mass flywheel, clutch disc, and Valeo pressure plate. All items are brand new in original boxes. Also included is a new pilot bearing, balancing weights, and clutch alignment tool. The flywheel is "unopened", still sealed in plastic to a piece of cardboard. The DMF will fit 89+ L98 and LT1/4, but the pressure plate is LT1/4 specific.
** 8/23/2014 EDIT **
The flywheel and pressure plate have been sold. I still have the clutch disc and throwout bearing. They are both aftermarket pieces. I'll take $100 shipped for both.
Let me know if interested!
** END EDIT **
Photos:
Last edited by 85z51vette; 08-23-2014 at 03:33 PM. Reason: Updated listing.
05-05-2014, 01:44 PM
#3
The flywheel of course is all years '89+ L98, LT1/4 BUT the pressure plate is going to be selective dependent upon the ID of the release bearing. Part #'s of the clutch components or the ID of the release bearing might increase the interest.
ID in this case would be Inside Diameter OR if there's a nylon insert in the bearing bore.
ID in this case would be Inside Diameter OR if there's a nylon insert in the bearing bore.
05-05-2014, 03:05 PM
#4
Racer
Thread Starter
Member Since: May 1999
Location: Nashville TN
Posts: 290
Likes: 0
Received 0 Likes
on
0 Posts
The flywheel of course is all years '89+ L98, LT1/4 BUT the pressure plate is going to be selective dependent upon the ID of the release bearing. Part #'s of the clutch components or the ID of the release bearing might increase the interest.
ID in this case would be Inside Diameter OR if there's a nylon insert in the bearing bore.
ID in this case would be Inside Diameter OR if there's a nylon insert in the bearing bore.
Last edited by 85z51vette; 05-09-2014 at 11:09 AM. Reason: Moved photos to first post.
05-06-2014, 10:46 AM
#5
Drifting
05-14-2014, 10:30 PM
#7
05-28-2014, 01:37 PM
#10
Racer
Thread Starter
Member Since: May 1999
Location: Nashville TN
Posts: 290
Likes: 0
Received 0 Likes
on
0 Posts
07-12-2014, 04:37 PM
#12
Racer
Thread Starter
Member Since: May 1999
Location: Nashville TN
Posts: 290
Likes: 0
Received 0 Likes
on
0 Posts
The flywheel and pressure plate have been sold. I still have the clutch disc and throwout bearing if anyone would like to make an offer.
Let me know if interested!
Let me know if interested!