*Some 86+ parts for sale....
#1
Drifting
Thread Starter
*Some 86+ parts for sale....
This stuff is taking up too much space (all prices plus shipping):
Used set of factory fuel injectors 50.00 SOLD
Used Walbro 255 lph fuel pump 65.00 Sold to Happydad
(I installed a new Edelbrock pump [turns out it's a Walbro too] as I thought this one was going bad. Turns out the pump was rubbing the mounting bracket and making all kinds of noise. I'll warranty this one for 30 days for peace of mind.)
Factory front y-pipe with pre-cats, cat, and A.I.R. tube 100.00 Trashed
(Would consider parting with just the A.I.R. tube for those interested, but I would need to cut it off as it has been welded to the cat)
A.I.R. pump 35.00 Sold to CorvAdel
Factory eaxhaust headers 40.00 each
Factory lower manifold w/EGR tube 50.00
Factory plenum 35.00
Rear y-pipe w/mufflers 60.00 Trashed
2 48mm throttle bodies (these need some work) 20.00 each
Small HEI distributor (for use with external coil) 85.00
fuel rail for 3rd gen f-body 60.00
MAF sensor 80.00 Sold to CorvAdel
I'll supply pics on requested parts.
Found some more parts!!!
Lower air filter housing (NIB) 85-89 45.00 Sold
Cut air filter lid (plastic model) <50 miles 25.00 Sold to Blownfuel1
K&N air filter <50 miles 20.00 Sold to Blownfuel1
Used set of factory fuel injectors 50.00 SOLD
Used Walbro 255 lph fuel pump 65.00 Sold to Happydad
(I installed a new Edelbrock pump [turns out it's a Walbro too] as I thought this one was going bad. Turns out the pump was rubbing the mounting bracket and making all kinds of noise. I'll warranty this one for 30 days for peace of mind.)
Factory front y-pipe with pre-cats, cat, and A.I.R. tube 100.00 Trashed
(Would consider parting with just the A.I.R. tube for those interested, but I would need to cut it off as it has been welded to the cat)
A.I.R. pump 35.00 Sold to CorvAdel
Factory eaxhaust headers 40.00 each
Factory lower manifold w/EGR tube 50.00
Factory plenum 35.00
Rear y-pipe w/mufflers 60.00 Trashed
2 48mm throttle bodies (these need some work) 20.00 each
Small HEI distributor (for use with external coil) 85.00
fuel rail for 3rd gen f-body 60.00
MAF sensor 80.00 Sold to CorvAdel
I'll supply pics on requested parts.
Found some more parts!!!
Lower air filter housing (NIB) 85-89 45.00 Sold
Cut air filter lid (plastic model) <50 miles 25.00 Sold to Blownfuel1
K&N air filter <50 miles 20.00 Sold to Blownfuel1
Last edited by silver86; 12-14-2006 at 02:40 PM.
#3
Drifting
Thread Starter
The injectors work perfectly. I needed to swap them out for 42#'ers for my blower install. There are two sets of numbers on the injectors:
5720XA530
10077514
I believe that these will fit an 85, both were batch fired. I'm not absolutely positive, but 99.9% sure. There should be a thread on that somewhere here.......
If I remember correctly, factory # rating was 22lb @ 42psi (but it could be 23#).
5720XA530
10077514
I believe that these will fit an 85, both were batch fired. I'm not absolutely positive, but 99.9% sure. There should be a thread on that somewhere here.......
If I remember correctly, factory # rating was 22lb @ 42psi (but it could be 23#).
Last edited by silver86; 07-04-2006 at 01:16 PM.
#13
Drifting
Member Since: Oct 2005
Location: bakersfield cali
Posts: 1,259
Likes: 0
Received 0 Likes
on
0 Posts
i will take one of the t body's if any of them have the coolant bypass aluminum plate under neath in tact. i also want the t body with the most spring tension on the throttle shaft. pm me
#15
Drifting
Thread Starter
Originally Posted by 90convert
what kind of shape is the rear y and mufflers in
#16
Drifting
Thread Starter
Originally Posted by 86VX1
i will take one of the t body's if any of them have the coolant bypass aluminum plate under neath in tact. i also want the t body with the most spring tension on the throttle shaft. pm me
Last edited by silver86; 07-20-2006 at 08:15 AM.
#19
Drifting
Thread Starter
I still have the factory headers. They do have all emissions tubing. The EGR pipe is still bolted to the stock intake (stripped bolt), but I could cut the bolt if you were interest in just the tube.
#20
Racer
Member Since: May 2006
Location: Alpine California
Posts: 286
Likes: 0
Received 0 Likes
on
0 Posts
Interested in the cut filter lid and the K&N, if nobody else has spoke up for them.How much to ship to Alpine, Ca 91901 (talk about al the way across the country!)