All are Aluminum, factory original, plus 1 over the counter GM, and a few aftermarket items.
Link---http://smg.photobucket.com/albums/v663/435rdster/Intake%20manifolds/---Link at end of post is working.

'65 3866963----$400.00----Plenum cut--396/425hp Corvette and Chevelle

'66 3885069----$600.00----Perfect--- 427/450hp Corvette 3 hole plenum





'66 3885069----$550.00----Perfect----2 hole plenum for '68 427/425hp Camaro and passenger, but outward appearances pass as '66 427'450hp Corvette

'67 3886093----$600.00----Perfect---Corvette L88 427/430hp


SOLD----'67 3890490----$500.00----Perfect---327/350hp---SOLD



'67 3890490----$300.00----bit of corrosion at thermostat,but it does not leak.

SOLD---'67 3894382--$2,200.00----Perfect, original, not a reproduction---3 x 2 oval port 427/400hp---SOLD





SOLD---'67 3894382--$2,000.00----Nice------same as above
Have matching carbs for above intake dated September of 1966, and original air cleaner, also some original '67 "smog" valve covers thar have been chromed.---All SOLD but valve covers.





'67/'68 3917610---$550.00---Perfect---Camaro Z28 302/290hp

'68 3919849---$350.00---Nice----427/390hp 1 x 4

'68 3919849---$450.00---Perfect---As above
Carb is SOLD--Have the original matching Q-Jet for the above manifold---427/390hp--7028209FG--dated rather late in the '68 production run---$1,000.00--also have the original air cleaner and filter, exhaust manifolds and------

Ta Da,

drum roll please,

Late production 1968 427/390hp original, complete A.I.R. (smog) system--every piece, all as it left the factory, dated, stamped, original marked hoses, etc., etc---$2,000.00

Actually have the complete engine----everything---as it came from the factory, late production, air cleaner to oil pan, fan/clutch to flywheel (have a couple of M21 transmissions for '68's, but not matched to this engine), exhaust manifolds, dip stick, shielding, distributor, correct/dated carb, clips, retainers, valve covers, every bracket and bolt original and correct. Excellent stamp pad broaching and stamping, low mileage---truly a "time capsule" example from 1968.---$6,000.00---will include the above original AIR (smog) system for a total price of $7,500.00.
Might part it all out---let me know what you need. Just so you know, I'll want $1,250.00 for the carb, $450.00 for the air cleaner assembly, you know what I want for the AIR system, $300.00 for the fan, $650.00 for the fan clutch, $500 for the valve covers, $325.00 for the intake manifold, $125.00 for the intake manifold blots, $75.00 for the thermostat housing and another $50.00 for the correct bolts, $700.00 for the heads and another $125.00 for the bolts, $300.00 for the oil pan, $150.00 for the front timing cover, $250.00 for the correct dip stick, $3,000.00 for the short block, $100.00 for the balancer, $125.00 for the cast iron lower crank pulley and another $40.0 for the correct bolts, $225.00 for the water pump and bolts, another $150.00 for the pulleys, $450.00 for the distributor, $250.00 for the shielding, $125.00 for the oil filter canister, $100.00 for the engine lift brackets, etc., etc.

'68 3919852---$1,200.00---Nice---Corvette 427/435hp 3 x 2

Have a couple of Hi-Per 3 x 2 air cleaners and a matched set of 4speed 3 x 2 carbs dated March of '68

Might have another 852--need to check.

SOLD---'68/'69 3933163---$600.00---Perfect--- 427/425hp Camaro/Chevelle---SOLD

'68/'69 3933163---$300.00---Perfect---427/425hp---GM over the counter replacement.

SOLD---'69 (and very late '68)---3937797---$1,400.00---Perfect--427/435hp Corvette---SOLD---Have 2 more of these---$1,250.00 per.





Have three of these (2 are perfect and one has some repairs) asking $900.00 for the welded piece.

Last of the aluminum intakes are aftermarket --small and big block---$Cheap

Forgot about this one--Winter's snowflake, Big Block, Rec. port, but I cannot find an application for it? Prototype/racing/Marine?





Also have a nice Offenhauser small block Chevy side by side 2 x 4 aluminum intake (it has '66 Mopar carbs on it)--$500.00

Have some small and big block cast iron intakes also--'57 thru '68

Have some 1 x 4 Hi-Per air cleaner bases and lids, steel and aluminum valve covers, timing covers, oil pans, dip sticks, etc.

Also have oval and rectangular port big block heads---1965 396/425hp 208's---$2,250.00 per set, '1967 427/390hp 390's----$700.00 per set, 391's, 1968 and 1969 427/435hp 840's---$1,200.00 per set, 1967 427/390hp 802's ---$700.00 per set, 063's, 290's, 291's--Also 1967 427/435hp aluminum 392's----$2,800.00 per set and 1968 427/435hp aluminum 842's---$2,500.00 per set.

Have some TI distributors/amps/harnesses---the '66 and the '67 TI units are sold. Have some '68 and '69 units availavle, and a couple of the 263 ball baring units. Have amps and harnesses.

Please see all of the manifold photos in my photobucket http://smg.photobucket.com/albums/v6...e%20manifolds/

Thanks,
George
210 748 4693
geopar@gvtc.com




http://smg.photobucket.com/albums/v6...r/My%20Vettes/

There are several albums in my photo bucket---please review any that interest you.

All cars have clean, non salvage titles.

1) '68 vert., 427/435hp (no engine), has original 4 speed, posi and F41 suspension, Red/Red vinyl, head rest seats, basket case (complete), lots of documentation---$5K or part out

2) '68 cp., 427/435hp, 4 speed, Safari Yellow/Black vinyl, no engine, no documentation, has all 427 Hi Horse Power components, tele column, speed minder speedo, has one piece hand laid front cap installed, complete car---$5K or part out

3) '68 vert., 327/350hp, 4 speed, LeMans Blue/Blue vinyl, air conditioned, Street rods suspension package, frame powder coated (beautiful), basket case, no front cap, parting out or will sell all for $6K.---SOLD --Cowl back body sale pending---SOLD---will post better photos of frame/suspension when body pulled.
Hard top is sold
Have a lot of '68 only parts with this.

4) '68 cp., 327/300hp, auto, air conditioned, Red/Gunmetal vinyl, no front cap, complete, minimal rust in frame (easy repair or I can do it for you), parting out or sell for $4K.---lots of good interior parts, good bumpers, good rear clip, good windshield frame and birdcage, good wiper door assembly, good a/c components, complete pop out rear window assembly and tray, T-Tops, good stainless, forward console and panels, good top dash, etc., etc.

5) '68 vert., 327/350hp, air conditioned, 4 speed, LeMans Blue/Blue vinyl, TI ignition, 370 posi, two top, no engine or trans, have all paperwork from factory (one family owned car), including order sheet, protecto plate, original title, radio instruction booklet and tag, instruction tags, etc., etc.. basket case, good, rust free rolling frame, most components there including headlight assemblies, wiper door assembly, bumpers, brackets, doors, stainless, etc., etc., But---body is toast---rusted birdcage and windshield frame, no front clip, no rear clip, just a "cockpit". Parting out or sell for $4K. Price reduced. The original factory paperwork is worth quite a pretty penny.

----SOLD---- '69 cp, 350/300hp Original engine, auto, British Green/Black vinyl, nice body, rusted frame in rear, interior gutted, otherwise complete.
Parting out or sell for $3.5K.---Sale pending minus engine and headlights, ----SOLD

Parts:

1) Everything for '68 except original "relief" finned turn signal grills, and I do mean everything. Only one shift plate left (4 sp with a/c)

2) Everything for '69.

3) Many '70-'72 parts.

Thanks,
George
210 748 4693
geopar@gvtc.com

Please see my listing for C1 and C2 cars/parts




All big block hoods have been sold (except for a couple of original L88'S).

SOLD----1970 LT1 hood--nice--$1,000.00---SOLD


SOLD---'69 427, original, red, with nice Chrome inserts, latches/cable
very nice condition----$1,100.00--SOLD

Sold--'70 LT1, original, in primer, very nice condition----$1,000.00---Sold

Sold--'70 454, original, in primer, very nice condition---$1,000.00---Sold

'68 L88, original, air box removed,----------------- $ 700.00

Sold----'68 L88, reproduction, no air box--------------------$ 500.00 Sold pending payment. Thanks Jim.---Sold

'68 L88, original, complete with air box, some old repairs, ---$1,000.00

SOLD--'69 L88, original, complete with air box, very nice condition----$2,000.00--SOLD

Two---'69 small block, original, very nice condition, latches and cable,------$200.00 each, or $125.00 without latches/cables.

Two---'68, small block, original, some repairs, $100.00 each

Have '68 only male and female hood latches and cables available. $125.00 per set

Have '69-'72 male and female hood latches and cables available. $75.00 per set

Have original hood props--'68-'72---$40.00



I am in South Central Texas, just North of San Antonio.

I accept cash, money orders, Paypal, personal checks (must clear before I ship), and barter (trades).

I ship via USPS, UPS, Fedex, Bus, and various freight companies for the heavier items (engines, frames, etc.).

I do not charge for packaging/handling (unless I need to build a crate for an engine, etc.), glad to combine shipments to reduce costs, and will ship according to your request (ie: Carrier of your choice, ammount of insurance, Sat. delivery, signed, etc.).

In some instances I may be able to personally deliver or meet you if I happen to be going your way---this is generally in the Texas areas of Dallas and Houston, but I do make some road trips and have contacts with over the road truckers that can at times be utilized.


1) SOLD--- 928 TI dist. with amp and harness (w w/g wire pigtail cut)-$ 850.00---Very nice Transistorized dist.--Offers?---SOLD
2) SOLD-- Original big block hood, red, nice chrome insets, latches---$1,000.00---Offers? ---SOLD
SOLD---3) '69 only wiper motor with headlight washer pump----------$ 350.00---SOLD--have 2 more. I have a few of the headlight washer pumps also.
4) wiper door actuator and bracket--------------------------$ 75.00
5) wiper door override switch------------------------------- $ 50.00----On the cowl.
6) 827/828 exhaust manifolds w/A.I.R holes------------------$ 500.00---These are very nice and originals
7) Standard steering column w/key, nice condition-----------$ 250.00--nice, good turn signal switch.
8) exhaust panel (under car exhaust) (one repair-original)----$ 100.00
9) big block dist shielding-----------------------------------$ 50.00
SOLD--10) 621 bell housing----------------------------------------$ 175.00----SOLD--Thanks
11) washer bag with original cap/hose-----------------------$ 125.00---SOLD--Thanks CF---Have 3 more of these
12) 4 ralleys (no trim) dated K18 9 19AZ (Sept. 19, 1968) $ 250.00---Good original ralleys--Have a bunch or rings and caps
13) steering box (unknown condition, but he said it was fine?) $ 50.00

SOLD--14) A/C components--complete (except for the wiper bezel and the console control/vacuum tubing)---inner and outer boxes, hard lines, mufler, brackets, evap, condensor, ducting, 3 groove water pump pulley, compressor, etc.--SOLD--have a few more pieces


I have some misc. a/c pieces--brackets, evap boxes, ducting, compressors, hoses, brass caps, a/c wiper bezels, a/c control units with complete vacuum tubing, inner boxes and controls, flappers, vacuum, wiring, Big Block brass expansion tanks and brackets, etc., etc.

I do have a correct wiper bezel, the console controls, the vacuum tubing, and any electrical that is needed from another '69 a/c car.
He kept that stuff in his Vette for appearances/fill the holes.

He has a nice set of big block pipe/mufflers and tips--very low mileage in great condition---$300.00?

Also has a nitrous kit.---If interested I'll get the specific info.


Big Block with a/c expansion tanks.
I have 3 of these, but one may be sold.---J69 SOLD
These are nice, no corrosion, good hose nipples, etc.
Have original brackets and bolts also.
Looking for $225.00 for tank, and $225.00 for set of brackets.
The one pending is dated J69, the other two are dated 70 and 71 (don't have the months in front of me).



Will post photos later. Link to photobucket: http://smg.photobucket.com/albums/v663/435rdster/Dannys%2068%20parting%2

Car and parts located in South Central Texas, near San Antonio.

Big items:

Update: Update: Update: Update:

SOLD----Update on frame and suspension package.---SOLD

Thanks to a fellow Forum member I have identified the supension package on this frame----
Vette Brakes and performance "SKU 42000" Full performance set----This is a $2,400.00 se

2) SOLD--- Cowl back convertible body (a/c car--4 sp.)--Nice birdcage/rocker channels/nice cowl, floors/nice rear body panels,--SOLD

new gas tank---$125.00


3) SOLD---SOLD---Complete hard top---Stainless/glass/weather stripping/liner/latches, etc.---$700.00

4) Soft top frame, no rust, needs canvas and weatherstripping----$650.00


5) Wiper door assembly---mechanism/door/grill with early '68 wiper nozzles/stainless trim and top of fender trim pieces/actuator/over ride switch/under dash over ride set-up/ etc., etc.---$650.00---not all items in photo, but all components here. Have extra pieces---grills, doors, stainless, mechanisms, vacuum cans, switches, nozzles, brackets, etc., etc.


6) '68 head light assemblies--Early, small door, metal bezels---$700.00


Two 4 speed drive shafts with yokes----$75.00 each Yokes worth this price.
New gas tank filler neck/cap-overflow cup---$75.00
Vacuum storage tank (two port) new paint---$100.00
A/C radiator support------$200.00--SOLD--Have another and a non a/c support
Metal fan shroud----$125.00---Sold one, have another
SOLD--- and '68 only lower shroud--$125.00---SOLD
Early '68 2 piece top receivers (on corners of windshield frame)---$200.00--sold one set, have another
'68 only top of windshield frame stainless (no mounting holes)/nice---$300.00
SOLD---Early 1st design "smooth" door handles---$125.00---Sold one set, have another.--SOLD
'68 door push buttons with trim bezels---$125.00 each--sold a couple, have a couple left.
'68 only door lock mechanisms---$100.00 each--sold two lefts, have a few right and left yet to sell.
Left dash, black, 6000 red line tach (327/350hp) and speedo---$175.00
Right dash '68 only, no map pocket---$100.00

'68 only interior pieces---2 sets of forward console extensions---$35.00 per piece
Convertible rear quarter panel interior trim----$150.00 each--Sold---working on another pair----Have complete cp. panels with courtey lamp assemblies available.
Convertible windshield header trim---$75.00
'68 steering column trim pieces (two sets)---$100.00 per set--Sold some--have more.

Bumper brackets--(all), and some extras---$10.00 to $75.00
Front "U" brace----$125.00--Sold ---have others.
4 speed pedal assembly and braces (no brake light switch)---$125.00--Sold one---have more.
'68 only brake light switch---$125.00---Sold two, have two more.
Rear view mirror and mounting bracket (convertible)---$50.00
'68 "smooth" gauge bezel (broken at thin areas) and green faced gauges---$150.00
Front parking light grills ('69 style) with lights and Chrome "hockey" sticks---$150.00 for the set, or split up--Sold--have some more.
'68 outer door handles (fair) $10.00 per, inner door lock ***** $5.00, 4 of the control rods-$10.00 per, one window handle $5.00, two of the spacers that go between the window handle and the door panel $5.00 per, and a couple of the access plates $10.00 small, $20.00 large-
4 '68 tail light lenses (no cracks)---$105.00 for all or $40.00 per--Sold a few, have a few more.
4 nice derby caps----$35.00 each---Sold a set---Have more.
'68 only wiper motor---$125.00--Sale pending--Have a couple more.
5 drop down air cleaner bases (350hp)---$50.00 each--Sold one.
2 chrome air cleaner lids (need chrome) $25.00 each
All wiring harnesses---dash, front lights, engine compartment, rear lights and fiver optics---I need to inspect these for completeness---will price when condition is determined. Do have extra sockets/partial harness pieces/etc. for those of you who need a piece or part. Have sold a few pieces and parts, have a lot more.
Side marker lights and brackets (4)---$25.00 for the set
'68 only reverse light housings/pigtails--$75.00 each ($125.00 pair)
'68 gas pedal, bracket, and cable assembly---$100.00--'68 only, hard to find.
4 speed shifter and linkage, with mount bracket, and rear trans bracket---$200.00 for the assembly--Sold one, have a few more.
2 4 speed shift plates ('68 only)---$100.00 per---Gone---might have another coning in.
2 sets of rocker moldings (lower fiberglass and upper stainless trim)-- fair condition----$140.00 per set
Smog pump and diverter valve, and one side hose/check valve/exhaust tube ---need to check numbers and Julian date-- will price when determined.
"Z" bar and clutch rod----$50.00
'69 steering wheel---$75.00---Sold.
Have 5 more---4 are perfect ($100.00)
top piece of ignition shielding and a couple of the side and spark plug pieces---$50.00
2 radio ground plates---$10.00 per
1 early, '68 only "square" cornered rear ventilation grill---These are difficult to find---$75.00
Pile of center cowl braces, brackets, and the seat belt and shoulder belt under body reinforcements---all powder coated--Will sell all for $200.00 or split up

Spare tire tub assembly---top/bottom/correct bolts (6" for '68)---nice condition------$150.00
SOLD--Front crossmember, '68 only, powder coated, nice----$125.00--SOLD
Extra headlight lid--later '68---$100.00
Misc. A/C components---boxes/compressor/condenser/brackets/drier/etc.
Early radio---need to check if it's '68 or '69 and if it's mono or stereo---Will price when determined.

All prices are OBO.

1) SOLD---Convertible body/title-------$2,500.00---SOLD
2) SOLD--- Hard top-------------------$ 700.00---SOLD
3) Soft top-------------------$ 900.00
4) wiper door assembly--------$ 650.00
5) early '68 headlight asmbs.---$ 700.00
6) bumper set-----------------$ 400.00



parts not listed/priced ( smog, a/c components (braces, compressor, ducting, '68 only center air deflector, etc.) , wiring, steering col./wheel, bumper braces/brackets, 2nd left lower dash w/speedo/tach, '74 exp. tank (aluminum), headlight shields, hood, hood latches and support, rear compartment doors, power brake booster, master cylinder (correct with bleeders), horn, em. brake handle assembly, door hinges and new springs, splash shields, headlight support bar, top surround reinforcement bar, top dash braces, door mirror, '68 only wiper arms.

Thanks,
George
210 748 4693
geopar@gvtc.com