1969 Underbody Metal Reinforcement finish
#1
Burning Brakes
Thread Starter
1969 Underbody Metal Reinforcement finish
I bought all new under body reinforcements for my 69 coupe. I'm looking for what the correct original finish should be. They came black semi gloss from Paragon. I want to get them plated so they won't rust at all in the future. I considered Zinc but it would be too bright I guess. I'm also considering blackening. I'm sure they will end up "over restored" but I don't want them to get rusted at all in the future.
#3
Drifting
Member Since: Aug 2010
Location: Charlotte Area North Carolina
Posts: 1,519
Received 214 Likes
on
153 Posts
https://www.grainger.com/product/54T...B&gclsrc=aw.ds
Here is a link to the Krylon semi-gloss black acrylic lacquer paint posted earlier if you need it.....
Here is a link to the Krylon semi-gloss black acrylic lacquer paint posted earlier if you need it.....
#4
Team Owner
Frame is painted black semi-gloss. That isnot the same as black semi-flat. Semi-flat is also labeled as 'satin'.
#6
Melting Slicks
Hope this helps a little.
Underbody Nut Plates
There are numerous sheet metal panels riveted to the underside of the body. These form mounting points for various internal body components such as the battery, battery cables, seats, jack and so on. All of these are dipped chassis black and held in place by aluminum rivets. The rivets are not painted. The seat belt anchor plates are cadmium plated. The rear seat anchor plate is a black phosphate while the front one is chassis black dip painted.
Underbody Nut Plates
There are numerous sheet metal panels riveted to the underside of the body. These form mounting points for various internal body components such as the battery, battery cables, seats, jack and so on. All of these are dipped chassis black and held in place by aluminum rivets. The rivets are not painted. The seat belt anchor plates are cadmium plated. The rear seat anchor plate is a black phosphate while the front one is chassis black dip painted.
#7
Burning Brakes
Thread Starter
Very helpful information. I knew about the semi gloss for the frame. I know what black phosphate looks like. I don't know what the cadmium finish looks like though. I'll have to look that one up. Now, if I could only remember how to post pictures. I posted a lot on my other thread but just forgot. I'll look on here I think there are instructions.
Thanks for the help.
Thanks for the help.
#10
Burning Brakes
Thread Starter
Here's everything I need to get plated or painted prior to install.
PJO, I see the Cadmium for the inner and outer seat belt reinforcements that's a huge help. Any other information on finishes would be appreciated.
#11
Melting Slicks
Not home right now will be latter will look over your items you have pictured.
Everything else would be dip painted semi-gloss black other than. #4 can be black but also have seen them just silver cad plated. #5 inboard ones tend to be gray phosphate finish and the outer black painted. #6 if they are for the heat insulation blankets natural.
Everything else would be dip painted semi-gloss black other than. #4 can be black but also have seen them just silver cad plated. #5 inboard ones tend to be gray phosphate finish and the outer black painted. #6 if they are for the heat insulation blankets natural.
Last edited by PJO; 05-21-2021 at 04:04 PM.
#12
Burning Brakes
Thread Starter
PJO, Thanks for the information. I have a friend that has access to all types of plating. I stalled out again on my project but this is one of the next steps I have to do.I'll send them out next week.
#13
Melting Slicks
Member Since: Jul 2010
Location: perth western australia
Posts: 3,101
Received 599 Likes
on
533 Posts
Have you checked the fit of those pieces ? Especially the outer bottom corner reinforcements (9) , my new ones were very bad and had to massaged to fit . Before they get plated ?
Last edited by bazza77; 05-22-2021 at 07:55 PM.
#15
Burning Brakes
Thread Starter
BAZZA 77, I got everything "massaged" to fit as you suggested. Time to send them out for plating.
Can Cadmium plating be painted of if I use an etching primer? I was going to get most of it Cad plated then paint the ones that should be black. Just looking for a little extra protection.
Can Cadmium plating be painted of if I use an etching primer? I was going to get most of it Cad plated then paint the ones that should be black. Just looking for a little extra protection.