** New Product, C6 Cup Holder Insulator **
#1
Le Mans Master
Thread Starter
** New Product, C6 Cup Holder Insulator **
*New Product* C6 Cup Holder Insulator
** This product fits all C6 Models 2005 thru 2013 C6/GS/Z06/ZR1 **
Are you searching for a low cost and easy method to prevent your cold drinks from boiling over? Our C6 Cup Holder Insulator will help keep your cold drinks cold longer? Reduce your cupholder area temperature to a more manageable level by using our easy to install C6 Cup Holder Insulator.
Installation is just a matter of pressing the Cup Holder Insulator into place. Laser cut for a perfect fit, 1/4 inch insulation covered in Black Neoprene Rubber for easy cleaning and a clear plastic pull tab for easy removal. Experience a noticeable reduction in temperature with an easy to install and inexpensive alternative.
ORDER HERE: http://www.topflightrepro.com/corvet...products.shtml
Simple Installation
Slide Insulator rubber side up into cup holder area
Press down
And Done!
** This product fits all C6 Models 2005 thru 2013 C6/GS/Z06/ZR1 **
Are you searching for a low cost and easy method to prevent your cold drinks from boiling over? Our C6 Cup Holder Insulator will help keep your cold drinks cold longer? Reduce your cupholder area temperature to a more manageable level by using our easy to install C6 Cup Holder Insulator.
Installation is just a matter of pressing the Cup Holder Insulator into place. Laser cut for a perfect fit, 1/4 inch insulation covered in Black Neoprene Rubber for easy cleaning and a clear plastic pull tab for easy removal. Experience a noticeable reduction in temperature with an easy to install and inexpensive alternative.
ORDER HERE: http://www.topflightrepro.com/corvet...products.shtml
Simple Installation
Slide Insulator rubber side up into cup holder area
Press down
And Done!
Last edited by Top Flight Reproductions; 05-28-2012 at 08:15 AM.
#4
Le Mans Master
Thread Starter
#6
On 6-19 I ordered the Cup Holder Insulator and the Center Console Insulator. I received them on 6-22 and installed them. Went for a drive today and the difference in temperatures are amazing. The products perform as described. Outstanding products and super fast service. I am very pleased.
#7
Le Mans Master
Thread Starter
On 6-19 I ordered the Cup Holder Insulator and the Center Console Insulator. I received them on 6-22 and installed them. Went for a drive today and the difference in temperatures are amazing. The products perform as described. Outstanding products and super fast service. I am very pleased.
#11
Le Mans Master
Thread Starter
#13
Le Mans Master
Thread Starter
#14
Sr.Random input generator
So what were the temps in your particular test? Did you leave the center console lid closed during the test? Me and my friend will get it if you have a special for both the cup holder and the center console liner, but as is, it's quite a bit of charge especially for the tiny cup holder insulators
#16
Le Mans Master
Thread Starter
#17
Burning Brakes
I saw your center console insulator and thought this needed doing... I just ordered a set from you! one suggestion. put the set in a small priority mail flat rate box, save a bit on shipping. thanks though!
#18
Le Mans Master
Thread Starter
#19
Le Mans Master
Thread Starter
*New Product* C6 Cup Holder Insulator
** This product fits all C6 Models 2005 thru 2013 C6/GS/Z06/ZR1 **
Are you searching for a low cost and easy method to prevent your cold drinks from boiling over? Our C6 Cup Holder Insulator will help keep your cold drinks cold longer? Reduce your cupholder area temperature to a more manageable level by using our easy to install C6 Cup Holder Insulator.
Installation is just a matter of pressing the Cup Holder Insulator into place. Laser cut for a perfect fit, 1/4 inch insulation covered in Black Neoprene Rubber for easy cleaning and a clear plastic pull tab for easy removal. Experience a noticeable reduction in temperature with an easy to install and inexpensive alternative.
ORDER HERE: http://www.topflightrepro.com/corvet...products.shtml
Simple Installation
Slide Insulator rubber side up into cup holder area
Press down
And Done!
** This product fits all C6 Models 2005 thru 2013 C6/GS/Z06/ZR1 **
Are you searching for a low cost and easy method to prevent your cold drinks from boiling over? Our C6 Cup Holder Insulator will help keep your cold drinks cold longer? Reduce your cupholder area temperature to a more manageable level by using our easy to install C6 Cup Holder Insulator.
Installation is just a matter of pressing the Cup Holder Insulator into place. Laser cut for a perfect fit, 1/4 inch insulation covered in Black Neoprene Rubber for easy cleaning and a clear plastic pull tab for easy removal. Experience a noticeable reduction in temperature with an easy to install and inexpensive alternative.
ORDER HERE: http://www.topflightrepro.com/corvet...products.shtml
Simple Installation
Slide Insulator rubber side up into cup holder area
Press down
And Done!
#20
Burning Brakes
I just received my order and wanted to say I take back my suggestion. everything arrived packed perfectly ! after driving my car around all day yesterday, the cupholder no longer heats up my cold drinks . It works really well
thanks very much guys
thanks very much guys