2000 C5 Hardtop MAP Sensor Location
#1
Cruising
Thread Starter
Member Since: Jan 2010
Location: Plano TX
Posts: 10
Likes: 0
Received 0 Likes
on
0 Posts
2000 C5 Hardtop MAP Sensor Location
I am getting a code P0107 and feel that with over 100K miles, the MAP sensor has finally bit the dust.
I cant seem to locate it and the only picture I though I saw shows that it is attached to the back of the manifold (right next to the fire wall).
Is this correct and is there and easy way to replace?
I cant seem to locate it and the only picture I though I saw shows that it is attached to the back of the manifold (right next to the fire wall).
Is this correct and is there and easy way to replace?
#5
Tech Contributor
Member Since: Dec 1999
Location: Anthony TX
Posts: 32,736
Received 2,180 Likes
on
1,583 Posts
CI 6,7,8,9,11 Vet
St. Jude Donor '08
Here ya go:
Sensor just pops out of that fitting.
BC
Sensor just pops out of that fitting.
BC
#6
Cruising
Thread Starter
Member Since: Jan 2010
Location: Plano TX
Posts: 10
Likes: 0
Received 0 Likes
on
0 Posts
Bill,
Great picture but is that the back of the manifold after it has been removed? If not, where exactly is that?
If it is the back of the manifold, I am probably going to punt to my local guy to fix for me rather than trying to do a weekend project and most likely do more damage in the process.
Great picture but is that the back of the manifold after it has been removed? If not, where exactly is that?
If it is the back of the manifold, I am probably going to punt to my local guy to fix for me rather than trying to do a weekend project and most likely do more damage in the process.
#7
Tech Contributor
Member Since: Dec 1999
Location: Anthony TX
Posts: 32,736
Received 2,180 Likes
on
1,583 Posts
CI 6,7,8,9,11 Vet
St. Jude Donor '08
YEP! Back of the intake. Heres what the top of the engine looks like with it removed:
BC
BC
#9
Tech Contributor
Member Since: Dec 1999
Location: Anthony TX
Posts: 32,736
Received 2,180 Likes
on
1,583 Posts
CI 6,7,8,9,11 Vet
St. Jude Donor '08
MAKE SURE that who ever does the repair just doesn't slide the manifold forward, replace the sensor and slide it back. If you look at the picture of the valley, you will see all kinds of sand and dirt.
The little Vacuum line is also critical to be properly connected. Its tough. If I were you I would purchase a nylon vacuum line repair kit from AutoZone / Advance and give it to the mechanic to extend the line. If its not connected properly, the HVAC Vents will not change properly.
BC
The little Vacuum line is also critical to be properly connected. Its tough. If I were you I would purchase a nylon vacuum line repair kit from AutoZone / Advance and give it to the mechanic to extend the line. If its not connected properly, the HVAC Vents will not change properly.
BC
The following users liked this post:
jpbikes (04-17-2022)
#11
Team Owner
#12
Advanced
I couldn't own a vette without sites like these
[QUOTE=Bill Curlee;1576783098]YEP! Back of the intake. Heres what the top of the engine looks like with it removed:
In the past few months I've had to replace my MAP sensor and then the Oil Pressure sensor... Researched topics via the site and got GREAT info and procedures.. Job done once and done right.. but I could never have even thought about doing myself...Thank you BILL and everyone else that has offered advice
In the past few months I've had to replace my MAP sensor and then the Oil Pressure sensor... Researched topics via the site and got GREAT info and procedures.. Job done once and done right.. but I could never have even thought about doing myself...Thank you BILL and everyone else that has offered advice
In the past few months I've had to replace my MAP sensor and then the Oil Pressure sensor... Researched topics via the site and got GREAT info and procedures.. Job done once and done right.. but I could never have even thought about doing myself...Thank you BILL and everyone else that has offered advice
In the past few months I've had to replace my MAP sensor and then the Oil Pressure sensor... Researched topics via the site and got GREAT info and procedures.. Job done once and done right.. but I could never have even thought about doing myself...Thank you BILL and everyone else that has offered advice