Tachometer calibration????
#1
Le Mans Master
Thread Starter
Member Since: Mar 2005
Location: Rocklin California
Posts: 7,631
Likes: 0
Received 11 Likes
on
11 Posts
Tachometer calibration????
My tachometer reads about 200 RPM less than it should at highway speeds. I have checked the speedometer, calibrated the transmission, rear end, and tire diameter and everything points to the tach. Is there an easy way to calibrate or should I leave it alone as 200 RPM is no big deal. At idle it's dead on, only when I get up to highway speeds is it off. Thanks
#2
Race Director
There is an adjustment on the tach head, but ithe unit has to come out of the car. You could probably calibrate it yourself if you also install a temporary electric tach. The adjustment on the tach is quite simple.
#4
Le Mans Master
Thread Starter
Member Since: Mar 2005
Location: Rocklin California
Posts: 7,631
Likes: 0
Received 11 Likes
on
11 Posts
No, I have a couple different rear ends I have tried along with gear calculators and no matter what rear, it's 200 RPM lower. Only at higher speeds as I have checked it at idle with a dwell tach.
#6
Le Mans Master
My 2 cents.
- Pat
#7
Race Director
#8
Melting Slicks
#9
Drifting
A very small mismeasurement in tire diameter can easily account for a 200 rpm perceived variation at speed. It is much easier to try several electronic tachs via temporary mountings to check the car's unit than it is to swap rear axle ratios.
#10
Safety Car
larry
#11
Team Owner
Member Since: Oct 2000
Location: Washington Michigan
Posts: 38,899
Received 1,857 Likes
on
1,100 Posts
Tach calibration is the same as speedo calibration - it's done by gaussing/degaussing the magnet cup with specialized equipment (on a bench), not with any mechanical adjustment.
#12
Race Director
John - On the C-1 tachs I remember being able to turn the head one way or another (but don't trust my memory!) to adjust the reading? or is that just to zero it out?
#13
Burning Brakes
Member Since: Dec 2002
Location: Hasbrouck Heights NJ
Posts: 1,062
Likes: 0
Received 4 Likes
on
3 Posts
Why not verify with the dwell tach? 3 or 4K RPM should be the same in the garage as driving, set the dwell tach so you can see it with the cluster tach and hit the gas. That and I would not expect 40 year old technology to be spot on, the cops used to give you 10MPH grace for speedometer error.
#14
Race Director
Member Since: Apr 1999
Location: Beverly Hills/Pine Ridge Florida
Posts: 10,733
Received 561 Likes
on
349 Posts
Brian Tilles, the owner, and one of our Chapter members, demonstrated the gauss/degauss machine he has. Actually calibrated at few tachs and speedos for us as a demo.
You spin the tach (or speedo) at a dead on known RPM, then "zap" the magnetic cup either imparting or removing magnetism from it.
THAT'S the way it's done. NO external adjustments at all.
Chuck
#16
Instructor
Member Since: Oct 2006
Location: Jupiter FL
Posts: 219
Likes: 0
Received 0 Likes
on
0 Posts
The adjustment of the hair spring on the tach head has to be done in conjunction with the proper gaussing/de-gaussing. You can tweak the spring to read what you want at highway speeds, but that may throw it out of whack at lower speeds.(or higher speeds.)
#17
Former Vendor
Member Since: Oct 2008
Location: California
Posts: 157
Likes: 0
Received 0 Likes
on
0 Posts
Absolutely correct! There is a small "arm" called a regulator that adjusts hair spring tension to "fine tune" the unit after the proper magnetizing, and demagnetizing procedure is followed. The unit must come out of the cluster to be serviced. Your tach is probably closer than you think, I would leave it alone. Another thing to think about, do you know that the speedo is "on the money" ? It may be off just a few mph and is compounding the problem.
#18
Race Director
Absolutely correct! There is a small "arm" called a regulator that adjusts hair spring tension to "fine tune" the unit after the proper magnetizing, and demagnetizing procedure is followed. The unit must come out of the cluster to be serviced. Your tach is probably closer than you think, I would leave it alone. Another thing to think about, do you know that the speedo is "on the money" ? It may be off just a few mph and is compounding the problem.
#19
Le Mans Master
Thread Starter
Member Since: Mar 2005
Location: Rocklin California
Posts: 7,631
Likes: 0
Received 11 Likes
on
11 Posts
Absolutely correct! There is a small "arm" called a regulator that adjusts hair spring tension to "fine tune" the unit after the proper magnetizing, and demagnetizing procedure is followed. The unit must come out of the cluster to be serviced. Your tach is probably closer than you think, I would leave it alone. Another thing to think about, do you know that the speedo is "on the money" ? It may be off just a few mph and is compounding the problem.
#20
Former Vendor
Member Since: Aug 2006
Location: Jeffersonville Indiana 812-288-7103
Posts: 76,656
Received 1,813 Likes
on
1,458 Posts
St. Jude Donor '08-'09-'10-'11-'12-'13-'14-'15
This was not an instrument of accuracy even when new! The tachometer calibration allowable variance is +/- 100 rpms so you are not far from that with what you have.
Willcox Inc.
Willcox Inc.
Last edited by Willcox Corvette; 11-15-2008 at 11:15 AM.