WTB supercharger or turbo kit 1988 corvette l98
#1
Instructor
Thread Starter
WTB supercharger or turbo kit 1988 corvette l98
Looking at purchasing a supercharger or turbo kit for a 1988 corvette
If anyone here has a kit for sale new or used please contact me
thanks,
shawn
If anyone here has a kit for sale new or used please contact me
thanks,
shawn
#7
Instructor
Member Since: Dec 2005
Location: Riverside CA
Posts: 188
Likes: 0
Received 0 Likes
on
0 Posts
I have a Polished SN93 with brackets, spacers, K&N air cleaner, Taper-lock 6 rib pulley, and 2 belts. The kit is minus the S-Turns for the blower to TPI conection. It made 7 Lbs of boost on my 350, and has exceptional low end response. I had a $700 rebuild done by Paradise Wheel about 2000 Miles ago. The Taper-lock pully set cost like $300 alone. I would like $850 for what I have.
PM me if interisted.
Thanks,
Chad
PM me if interisted.
Thanks,
Chad
#10
I have a Polished SN93 with brackets, spacers, K&N air cleaner, Taper-lock 6 rib pulley, and 2 belts. The kit is minus the S-Turns for the blower to TPI conection. It made 7 Lbs of boost on my 350, and has exceptional low end response. I had a $700 rebuild done by Paradise Wheel about 2000 Miles ago. The Taper-lock pully set cost like $300 alone. I would like $850 for what I have.
PM me if interisted.
Thanks,
Chad
PM me if interisted.
Thanks,
Chad
The parts that are missing, How much do these parts costs?
#11
Instructor
Member Since: Dec 2005
Location: Riverside CA
Posts: 188
Likes: 0
Received 0 Likes
on
0 Posts
This set up is best used with a 350 or smaller as the blower is rated for 850 CFM. It will make about 7# of boost but also has RPM limitation for the pullie I have on it. It should be ran at 4800 and below.
It is best suted for a TPI 350 as thay run out of power @ 4500+ anyway.
They are quite reliable if you don't continualy over-rev these units.
I ran it on my 383 , cammed, AFR heads and it made 6# but my cam wants to rev higher so I switched to a Vortech "T" trim.
Dispite the claimes tha these ball drives are in-efficient, this Paxton made more power up to 4000 RPM than my Vortech T.
I have everything to mount this unit less the S-turns (I used for the Vortech)
I would call Greg at Blower works to see what the S-Turns costs new.
I have sean them used from time to time on E-Bay.
1 Pic is installed for visual.
1 Pick is the parts on the bench that are what is included with what I am selling
Good Luck
Chad
It is best suted for a TPI 350 as thay run out of power @ 4500+ anyway.
They are quite reliable if you don't continualy over-rev these units.
I ran it on my 383 , cammed, AFR heads and it made 6# but my cam wants to rev higher so I switched to a Vortech "T" trim.
Dispite the claimes tha these ball drives are in-efficient, this Paxton made more power up to 4000 RPM than my Vortech T.
I have everything to mount this unit less the S-turns (I used for the Vortech)
I would call Greg at Blower works to see what the S-Turns costs new.
I have sean them used from time to time on E-Bay.
1 Pic is installed for visual.
1 Pick is the parts on the bench that are what is included with what I am selling
Good Luck
Chad
#16
you said you used this on a 383.i have a 91 383 ,afr heads,super ram,agressive cam,dont know exact compression, just purchased car,thinkit would work with no internal mods.
#17
Instructor
Thread Starter
yeah i would say it would. 5 or 7 lbs no problem. i would buy it just somewhat cautious of the paxton s/c. he is stand up guy pm him for his phone number and he can answer any questions you have
#19
Racer
Member Since: Feb 2006
Location: san antonio TEXAS
Posts: 423
Likes: 0
Received 0 Likes
on
0 Posts