Can You Clean And Reuse Fouled Plugs?
#4
Race Director
If you "glass bead" them to remove all the carbon they will work just fine. Otherwise use new. I keep a bunch of cleaned spares for my Harleys and also do a lot for other scooter owners. It will not hurt any plugs however.
Last edited by Ironcross; 04-16-2006 at 10:52 PM.
#8
Race Director
Originally Posted by Corvette69w427
I bet you also pull your air filter off, bash it against the side of the vette, slap it back in and say "good as new".
REPLACE THEM!
REPLACE THEM!
I also clean my spark plugs. Unless the electrodes are worn there's nothing wrong with them. I have a little spark plug cleaner that uses shop air and glass beads the plugs. They come out like new. Just have to be careful to properly wash them off with carb cleaner before use to make sure no abrasive is lodged in them.
#9
Drifting
it depends on the situation, i hate shotgun answers. If its been 40k since you replace the plugs then personally i would get new ones.
However, i also own a plug cleaner. For example i was troubleshooting a carb problem once and every time i started the motor to test the latest change it would foul the plugs. while it is true i may not be the best troubleshooter, i would have had to buy several sets of plugs after it was all said and done and the problem was not the plug.
all i am saying is it depends on how old the plug is and the environment it is in.
i never replace parts that are not broken.
However, i also own a plug cleaner. For example i was troubleshooting a carb problem once and every time i started the motor to test the latest change it would foul the plugs. while it is true i may not be the best troubleshooter, i would have had to buy several sets of plugs after it was all said and done and the problem was not the plug.
all i am saying is it depends on how old the plug is and the environment it is in.
i never replace parts that are not broken.
#10
Originally Posted by Corvette69w427
I bet you also pull your air filter off, bash it against the side of the vette, slap it back in and say "good as new".
REPLACE THEM!
REPLACE THEM!
I will normally replace them. But I fouled a new set recently (too rich) when I put my Demon on after only 10 miles. So I used some brake clean, cleaned em off and put em back in.
#11
Melting Slicks
Member Since: Mar 2003
Location: Indianapolis IN
Posts: 3,472
Received 444 Likes
on
322 Posts
Finalist 2020 C4 of the Year - Unmodified
C4 of Year Finalist (stock) 2019
Originally Posted by Ironcross
If you "glass bead" them to remove all the carbon they will work just fine. Otherwise use new. I keep a bunch of cleaned spares for my Harleys and also do a lot for other scooter owners. It will not hurt any plugs however.
But automotive plugs are alot cheaper than aircraft plugs...I would just replace them.
#12
Melting Slicks
Thread Starter
Member Since: Apr 2000
Location: Ft. Walton Beach, Fl USA
Posts: 2,145
Likes: 0
Received 1 Like
on
1 Post
Thanks for the replies. I always keep replacement plugs on hand so thats not an issue. This is one of those instances where the plugs are brand new but fouled because of a too rich DEMON. I use ACCEL shorty plugs at $3-4 a piece so it can get pricey if they really don't need to be replaced.
I cleaned them with a brass bristle toothbrush, blew 'em out with compressed air and regapped them. I also rejetted the DEMON. So I think I'll put 'em back in and see if it works. If not I'll replace them. I'll let ya'll know how it plays out. Thanks again.
I cleaned them with a brass bristle toothbrush, blew 'em out with compressed air and regapped them. I also rejetted the DEMON. So I think I'll put 'em back in and see if it works. If not I'll replace them. I'll let ya'll know how it plays out. Thanks again.
#13
Race Director
Nastee: That's not a good way to clean them. The brass will imbed itself into the porcelin and make a low-resistance shunt to the shell loosing spark energy. Either glass bead them or replace. Wire-brushing is a no-no.
#14
Melting Slicks
Thread Starter
Member Since: Apr 2000
Location: Ft. Walton Beach, Fl USA
Posts: 2,145
Likes: 0
Received 1 Like
on
1 Post
Originally Posted by zwede
Nastee: That's not a good way to clean them. The brass will imbed itself into the porcelin and make a low-resistance shunt to the shell loosing spark energy. Either glass bead them or replace. Wire-brushing is a no-no.
#16
Race Director
Member Since: Jan 2000
Location: Corsicana, Tx
Posts: 12,603
Received 1,874 Likes
on
912 Posts
2020 C2 of the Year - Modified Winner
2020 Corvette of the Year (performance mods)
C2 of Year Winner (performance mods) 2019
2017 C2 of Year Finalist
Blasting will work....but you will often find that the rougher surface of the porcelain seems to attract gunk easier the next time around.
One thing I do when I'm "back road tuning" is to just change one plug..typically #6 on a bigblock..it usually runs leanest..... to work out the mixture and get close. That way if I get one all barfed up I just stick a new one in that hole and continue on until I get the right tune. When I'm all done..I either clean that set or stick a whole new set in.
Even running a Dominator, a big cam, 11.06 compression and street driving..I very seldom ever change plugs. I race with the same set I street drive with.....if it's tuned right, they don't get messed up and don't miss.
JIM
One thing I do when I'm "back road tuning" is to just change one plug..typically #6 on a bigblock..it usually runs leanest..... to work out the mixture and get close. That way if I get one all barfed up I just stick a new one in that hole and continue on until I get the right tune. When I'm all done..I either clean that set or stick a whole new set in.
Even running a Dominator, a big cam, 11.06 compression and street driving..I very seldom ever change plugs. I race with the same set I street drive with.....if it's tuned right, they don't get messed up and don't miss.
JIM
#17
Le Mans Master
The thing about those abrasive plug blasters that I worry about is what happens if you don't get all the grit out of the plug before you reinstall? Can't be good for the bores/rings/piston skirts if it gets down in there.
Just me worrying too much?
-Mark.
Just me worrying too much?
-Mark.
#18
Le Mans Master
Member Since: Mar 2006
Location: Tracy California
Posts: 5,427
Likes: 0
Received 0 Likes
on
0 Posts
REPLACE THEM !!!!!!!!!!!!!!!!!!!!!!!
medium grade sparkers cost just $8 a piece, that's a total of $128 (sometimes less, cheapest are 4 bucks a piece)
If you can't spend that much, why are you talking about sand blasting and bead blasting, which might end up costing you even more....
medium grade sparkers cost just $8 a piece, that's a total of $128 (sometimes less, cheapest are 4 bucks a piece)
If you can't spend that much, why are you talking about sand blasting and bead blasting, which might end up costing you even more....
#19
Team Owner
Member Since: Apr 2002
Location: Zionsville, PA NRA Life Member
Posts: 25,778
Likes: 0
Received 0 Likes
on
0 Posts
St. Jude '03-'04-'05-'06-'07-'08-'09-'10
Originally Posted by 73L48 Dave
You can clean them by glass bead blasting. This is a standard maintenence procedure used on piston aircraft.
But automotive plugs are alot cheaper than aircraft plugs...I would just replace them.
But automotive plugs are alot cheaper than aircraft plugs...I would just replace them.
Unleaded fuel contaminates the plugs. They never seem to "dry" correctly. Just replace them for the best performance.
#20
Race Director
Member Since: Jan 2000
Location: Corsicana, Tx
Posts: 12,603
Received 1,874 Likes
on
912 Posts
2020 C2 of the Year - Modified Winner
2020 Corvette of the Year (performance mods)
C2 of Year Winner (performance mods) 2019
2017 C2 of Year Finalist
$8 spark plugs?? $124 a set? Two sets?
Either way..you need to do some price shopping.....bad boy race plugs don't cost that much until you get to the ridiculous stuff to try and live in killer nitrous motors. But even most of those guys don't use those!
JIM
Either way..you need to do some price shopping.....bad boy race plugs don't cost that much until you get to the ridiculous stuff to try and live in killer nitrous motors. But even most of those guys don't use those!
JIM